OPA251PA - 25µA Low-Power Rail-to-Rail Op Amp | Texas Instruments
料号: OPA251PA ✓ 量产中OPA251PA 概述
An operational amplifier is an analog signal-conditioning semiconductor that amplifies the voltage difference between its inverting and non-inverting inputs. The OPA251 belongs to the broader hierarchy of operational amplifier, analog amplifier, amplifier IC, and power management semiconductor. Its micropower design is especially useful where battery energy must be conserved while the output must remain capable of driving a measurement, control, or conversion stage.
Important characteristics include 25 µA typical supply current, low input offset voltage, high common-mode rejection, and high open-loop gain. The 35 kHz gain-bandwidth product supports low-frequency signal conditioning, while the 0.01 V/µs slew rate is suitable for modest-amplitude waveforms. Rail-to-rail output operation increases usable output range in systems whose supply voltage is constrained.
The OPA251 uses a micropower internal architecture optimized for portable instrumentation rather than high-speed signal processing. With one amplifier in the 8-pin PDIP package, it supports cost-sensitive analog designs that need a single operational amplifier without the overhead of a dual or quad device. The 1.35 V minimum supply voltage also makes it applicable to low-energy sensor and monitoring circuits.
Typical uses include battery-powered sensor conditioning, portable measurement instrumentation, low-current analog signal processing, and the input stage of an analog-to-digital converter. In a typical application, the amplifier processes a sensor voltage referenced around ground, gains the signal to an appropriate level, and presents it to an ADC or comparator while minimizing standby current.
Designers should account for the 35 kHz bandwidth when selecting closed-loop gain and signal frequency. Input and output stability must be evaluated using the recommended application circuit, and the circuit must remain within the 1.35 V to 18 V supply range. Decoupling capacitors should be placed close to the supply pins to minimize supply disturbance.
This page organizes the OPA251PA electrical characteristics, package information, replacement considerations, and application guidance into an engineering-focused reference. It also identifies where an alternative is technically appropriate and, equally important, where a footprint or parameter mismatch makes a substitution unsuitable.
直接替换替代料: OPA251PA ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
OPA251PAG4
✅ 直接替换📋 参考替代料(不在目录中)
OPA251PA 最大额定值与电气特性
| Amplifier Type | Single operational amplifier |
| Supply Architecture | Single supply |
| Number of Channels | 1 channel |
| Nominal Supply Voltage | 15 V |
| Operating Supply Voltage Range | 1.35 V to 18 V |
| Typical Quiescent Current | 25 µA |
| Gain-Bandwidth Product | 35 kHz |
| Slew Rate | 0.01 V/µs |
| Output Swing | Rail-to-rail |
| 封装 | 8-pin PDIP |
| 安装类型 | Through-hole |
OPA251PA 8-pin pdip 引脚配置指南
OPA251PA(8-pin pdip 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: OPA251PA.
请参阅 数据手册 以查看完整引脚配置。
典型应用
OPA251PA 适用于 3 应用s: 信号调理, 数据采集, 音频处理.
信号调理
使用 OPA251PA 放大和滤波传感器信号。
数据采集
使用 OPA251PA 将模拟信号转换为数字信号进行处理。
音频处理
使用 OPA251PA 进行音频信号放大和处理。
工程参考数据: OPA251PA ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | OPA251PAG4 |
|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP |
| Brand | Texas Instruments | Texas Instruments |
| Amplifier Configuration | Single amplifier | Single amplifier |
| Supply Type | Single supply | Single supply |
| Supply Voltage Range | 1.35 V to 18 V | 1.35 V to 18 V |
| Typical Quiescent Current | 25 µA | 25 µA |
| Gain-Bandwidth Product | 35 kHz | 35 kHz |
| Slew Rate | 0.01 V/µs | 0.01 V/µs |
| Output Swing | Rail-to-rail | Rail-to-rail |
关键差异点
- Very low quiescent current for a general-purpose amplifier (对比 OPA251PAG4)
- Single-supply operation extends to 1.35 V (对比 OPA251PAG4)
- Same 8-pin PDIP mechanical interface (对比 OPA251PAG4)
设计说明
Use the 25 µA typical quiescent current as the baseline for low-power design, but include feedback-network and load currents in the complete power budget. For a single-supply circuit, bypass the supply pins with ceramic capacitance placed close to the package and follow the manufacturer datasheet's recommended values. Check that the bypass capacitor's DC bias rating remains effective at the actual supply voltage.
Treat the 35 kHz gain-bandwidth product as the primary limit on usable closed-loop bandwidth. Increasing closed-loop gain reduces bandwidth and can also increase output-noise contribution. For sensor signals, select a gain that keeps the signal bandwidth below the corresponding gain-bandwidth limit with margin, then verify phase margin and output settling using the datasheet curves for the intended operating supply.
Do not assume that the rail-to-rail output specification removes all common-mode restrictions at the input. Verify the input common-mode range, output swing, offset behavior, and stability against the manufacturer datasheet for the selected gain and load. The 0.01 V/µs slew rate can also limit large-amplitude output transitions, making it unsuitable for fast pulse or waveform requirements.
Keep the 8-pin PDIP footprint and its pin assignments unchanged when using OPA251PAG4 as the lead-free ordering option. Confirm orientation against the pin-description table in the manufacturer datasheet rather than a generic operational-amplifier symbol. Maintain a low-impedance ground return and place input components so their parasitic capacitance does not create excessive feedback or reduce phase margin.
合规信息
The OPA251PA is a general-purpose operational amplifier rather than an automotive-qualified device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements require confirmation from the manufacturer's current product or material documentation.