P1010NXE5KHA - QorIQ P1010 1GHz e500v2 MPU 425-TEPBGA | NXP
MPN： P1010NXE5KHA ⚠ 最後購買機會P1010NXE5KHA 概覽
A communications processor (also called a network SoC or embedded MPU) is a highly integrated system-on-chip that combines one or more CPU cores with networking peripherals, security engines, and memory controllers on a single die. Within the broader taxonomy, the P1010 sits under microprocessor (MPU) -> embedded processor -> SoC -> semiconductor. QorIQ P1 series parts target entry-level to mid-range networking equipment such as branch-office routers, industrial gateways, and secure IoT appliances where deterministic networking performance and integrated security matter more than raw compute.
Key features of the P1010NXE5KHA include 32 KB instruction and 32 KB data L1 caches per core, a 256 KB L2 cache with ECC, integrated SEC 4.0 cryptographic accelerator (AES, DES/3DES, Kasumi, MD5, SHA-1/2, and public-key engines), one GbE MAC, two PCIe Gen2 controllers, two SATA 2.0 ports, USB 2.0 with ULPI interface, DDR3/DDR3L memory controller with ECC, NAND flash controller, and a trust architecture supporting secure boot. The 45 nm process node keeps typical power dissipation under 3 W at full load.
Architecturally, the e500v2 core uses a 7-stage pipeline with out-of-order execution, dual-issue superscalar, and Book-E instruction set compatibility. The integrated SEC engine offloads bulk crypto from the host CPU, allowing line-rate IPsec on GbE interfaces without starving application code. Hardware-isolated trusted boot verifies signed firmware before releasing the platform, hardening devices against rootkit injection.
Typical applications include industrial IoT gateways, branch-office routers, secure VPN concentrators, factory-floor protocol converters (Modbus/Profinet/EtherNet/IP), fanless embedded appliances, and ruggedized edge networking nodes. Designers choose the P1010 when they need GbE throughput, hardware crypto, and Linux BSP support in a power envelope small enough for passive cooling.
When designing with this device, allocate 4-layer PCB minimum with continuous ground planes under the BGA, follow NXP's QorIQ hardware design guide for DDR3 trace length matching within 25 mil across the byte lanes, and provide a thermal solution sized for 3-5 W sustained dissipation in sealed enclosures. The 19x19 mm TEBGA I package uses lead-free SAC405 solder balls requiring MSL3 handling.
This page synthesizes distributor pricing, datasheet parameters, drop-in same-family alternatives, and practical hardware design notes not found in any single manufacturer datasheet, helping embedded engineers evaluate, source, and lay out the P1010NXE5KHA more efficiently than distributor catalog pages.
直接替換替代品，適用於 P1010NXE5KHA — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： P1010NXE5KHA （相同外形與佔位） — 差異在於 Ethernet, Memory Controller, Operating Temperature, PCIe, Package.
P1010NXN5KHA
✅ 直接替換聯絡詢價
查看資料表 →P1010NSN5HHB
✅ 直接替換📋 參考替代品（不在目錄中）
P1014NXN5FFB
✅ 直接替換📋 參考替代品（不在目錄中）
P1010NSE5KHA
✅ 直接替換聯絡詢價
查看資料表 →P1010NSD5HFB
✅ 直接替換📋 參考替代品（不在目錄中）
P1010NXE5KHA 最大額定值與電氣特性
| Manufacturer | NXP Semiconductors |
| Series | QorIQ P1 |
| Core | PowerPC e500v2 |
| Core Count | 1 |
| 資料匯流排寬度 | 32-bit |
| Max Core Frequency | 1.0 GHz |
| L1 Cache (I/D per core) | 32 KB / 32 KB |
| L2 Cache | 256 KB (with ECC) |
| 工作溫度 | -40C to +105C (extended) |
| 供應電壓 | 1.0 V core (typical) |
| 封裝 | 425-TEPBGA I (19x19 mm) |
| Process Node | 45 nm |
| Security Engine | SEC 4.0 (AES, DES, Kasumi, SHA, PK) |
| Ethernet | 1x GbE MAC |
| PCIe | 2x PCIe Gen2 |
| SATA | 2x SATA 2.0 |
| USB | USB 2.0 with ULPI |
| Memory Controller | DDR3/DDR3L with ECC |
| NAND Flash Controller | Yes (with ECC) |
| Trusted Boot | Yes (secure boot chain) |
| RoHS 狀態 | Compliant |
| MSL 等級 | MSL3 (per JEDEC J-STD-020) |
P1010NXE5KHA 425-tepbga i (19x19 mm) 腳位配置指南
P1010NXE5KHA（425-tepbga i (19x19 mm) 封裝）的腳位配置。 此數位 IC 包含 GPIO、通訊介面（UART、SPI、I2C）與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料： P1010NXE5KHA.
請參閱 資料表 以查看完整腳位配置。
典型應用
P1010NXE5KHA 適用於 6 應用s: Industrial IoT Gateway, Branch-Office Router, Secure VPN Concentrator, Factory Floor Protocol Converter, Fanless Edge Networking Appliance, Ruggedized Outdoor Router.
Industrial IoT Gateway
The P1010NXE5KHA fits industrial IoT gateways because its 1.0 GHz e500v2 core, integrated GbE MAC, two PCIe Gen2 lanes, and SEC 4.0 cryptographic engine deliver deterministic protocol conversion and hardware-offloaded TLS/IPsec on a single SoC. The -40C to +105C operating range suits outdoor enclosures, factory floors, and remote telemetry cabinets. With DDR3 ECC and trusted boot, the part provides the data-integrity and secure-boot chain required for IIoT nodes facing public networks.
推薦
Branch-Office Router
The P1010NXE5KHA's integrated GbE MAC, PCIe Gen2 for external radios, and hardware-accelerated SEC 4.0 make it suitable for branch-office routers handling line-rate IPsec on a single Gigabit interface. The 1.0 GHz core sustains routing tables for small sites, while the e500v2 Book-E architecture supports real-time QoS queues. Extended-temperature grade allows deployment in unconditioned telecom closets and outdoor enclosures without active cooling.
推薦
Secure VPN Concentrator
For secure VPN concentrators, the P1010NXE5KHA delivers SEC 4.0 hardware acceleration that offloads AES, DES/3DES, Kasumi, SHA-1/2, and public-key crypto from the host CPU. This allows the e500v2 core to focus on tunnel management and policy enforcement rather than bulk cryptography. The trusted boot chain and tamper-resistant design harden the platform against firmware injection, supporting FIPS-style deployments when properly configured.
推薦
Factory Floor Protocol Converter
In factory-floor protocol converters for Modbus/Profinet/EtherNet/IP bridging, the P1010NXE5KHA's GbE MAC, PCIe for fieldbus cards, and 256 KB L2 with DDR3 ECC provide deterministic message handling with error detection. The extended-temperature grade supports deployment in unconditioned cabinets near welding equipment or motor drives. SEC hardware acceleration secures OPC-UA traffic between legacy PLCs and modern MES/ERP systems.
推薦
Fanless Edge Networking Appliance
The P1010NXE5KHA's typical sub-3 W power envelope and 19x19 mm TEBGA package enable fanless edge networking appliances with sealed IP65 enclosures. Its DDR3L low-voltage support and integrated peripherals eliminate the need for companion chips in compact designs. The GbE MAC, PCIe, and USB 2.0 cover the typical I/O mix for edge sensors and small-cell backhaul, while trusted boot secures unattended remote nodes.
推薦
Ruggedized Outdoor Router
The P1010NXE5KHA's -40C to +105C junction temperature range, hardware crypto, and integrated GbE make it ideal for ruggedized outdoor routers in roadside cabinets, railway signaling, and mining sites. The DDR3 ECC controller prevents single-event upsets in high-altitude or radiation-prone environments. Trusted boot and SEC 4.0 protect against physical tampering, and the small TEBGA package suits compact IP67 enclosures.
推薦
推薦產品摘要
工程參考資料，適用於 P1010NXE5KHA — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | P1010NXN5KHA | P1010NSN5HHB | P1014NXN5FFB | P1010NSE5KHA | P1010NSD5HFB |
|---|---|---|---|---|---|---|
| Package | 425-TEPBGA I (19x19) | 425-TEPBGA I (19x19) - same | 425-TEPBGA I (19x19) - same | 425-TEPBGA I (19x19) - same | 425-TEPBGA I (19x19) - same | 425-TEPBGA I (19x19) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core | PowerPC e500v2 | PowerPC e500v2 | PowerPC e500v2 | PowerPC e500v2 | PowerPC e500v2 | PowerPC e500v2 |
| Core Count | 1 | 1 | 1 | 1 | 1 | 1 |
| Max Core Frequency | 1.0 GHz | 1.0 GHz | 1.0 GHz | 1.0 GHz | 1.0 GHz | 1.0 GHz |
| L2 Cache | 256 KB (with ECC) | 256 KB (with ECC) | 256 KB (with ECC) | 256 KB (with ECC) | 256 KB (with ECC) | 256 KB (with ECC) |
| Operating Temperature | -40C to +105C (extended) | Different NXP grade suffix | Different NXP grade suffix | Different NXP grade suffix | Different NXP grade suffix | Different NXP grade suffix |
| Security Engine | SEC 4.0 | SEC 4.0 (same family) | SEC 4.0 (possibly different revision) | SEC 4.0 | SEC 4.0 | SEC 4.0 |
| GbE MACs | 1 | 1 | 1 | Higher GbE count (P1014) | 1 | 1 |
主要差異化特點
- Extended -40C to +105C operating temperature grade (對比P1010NXN5KHA)
- Single integrated SEC 4.0 cryptographic accelerator (對比P1014NXN5FFB)
- Sub-3 W typical power envelope for fanless deployment (對比P1014NXN5FFB)
設計說明
Allocate at least a 4-layer PCB for P1010NXE5KHA, with continuous ground planes directly under the 425-TEPBGA I footprint. Per NXP QorIQ hardware design guides, route DDR3 traces within 25 mil length matching across each byte lane and 50 mil between lanes. Keep PCIe Gen2 differential pairs to 90 ohm impedance and isolate them from GbE and SATA traces to minimize crosstalk on the dense 19x19 mm BGA footprint.
The P1010NXE5KHA dissipates approximately 3-5 W typical at full CPU and GbE load. In sealed enclosures, provide either a small heatsink bonded to the TEBGA lid or a copper spreader (minimum 4 sq cm of 2 oz copper). For passively cooled designs targeting +105C ambient, validate junction temperature via NXP's thermal model. Derate by 30% when stacking multiple P1010NXE5KHA devices in compact router assemblies.
Do not use the P1010NXE5KHA in new designs without first checking NXP's QorIQ P1 product change notices for last-time-buy windows and replacement parts. The 'NXE' extended-temperature grade is specifically a -40C to +105C variant - mistaking it for the 0C to 85C commercial grade will cause field failures in cold-started outdoor installations. Also note: trusted boot requires a properly signed image or the SoC will halt; review NXP's secure boot fuse programming guide.
Use NXP's recommended PMU sequencing (TPS65820 or compatible) to enforce the 1.0 V core rail rise before 3.3 V I/O ramps. Decouple each VDD/VSS pair with 100 nF X7R capacitors placed within 2 mm of the BGA balls, plus a single 10 uF bulk capacitor per supply domain. DDR3 VTT termination must be enabled and matched to the selected DDR3L memory topology.
合規資訊
RoHS compliant per NXP product page. Lead-free SAC405 BGA balls. Not AEC-Q100 qualified (industrial/communications grade, not automotive). Halogen-free status not explicitly listed in the retrieved web data - confirmed unknown.
