P1010NSN5HFA - QorIQ P1 800MHz e500v2 SoC, GbE/PCIe/SATA | NXP
MPN： P1010NSN5HFA ✓ 啟用中P1010NSN5HFA 概覽
A QorIQ communications processor is a highly-integrated system-on-chip built on the Power Architecture instruction set, designed to replace older PowerQUICC multi-chip designs in cost- and power-sensitive networking endpoints. Within the NXP portfolio hierarchy, the QorIQ P1 series sits below the higher-performance P2/P3/P4 tiers and above the older PowerQUICC II/III families, targeting embedded networking, industrial control, and entry-level communications infrastructure where single-core performance and low power (as low as 1.1 W typical) are sufficient.
Key features of the P1010NSN5HFA include the e500v2 core with hardware virtualization and signal processing extensions, integrated SATA II controller, USB 2.0 with PHY, dual GbE interfaces, PCIe Gen1/Gen2 controller, DDR3 memory controller with ECC support, hardware-accelerated trusted boot using NXP Security Engine, and four TDM/HDLC ports for legacy telecom connectivity. The integrated peripherals allow designers to build a complete network-attached product without external bridges.
The 45 nm process technology combined with aggressive clock gating allows the P1010 platform to deliver PowerQUICC-class functionality at a fraction of the power budget of earlier generations, enabling fanless industrial designs and PoE-powered endpoints. The integrated security engine provides secure boot and run-time integrity verification for tamper-resistant deployments.
Typical applications include IP cameras and surveillance encoders, industrial robotics and machine vision controllers, factory automation gateways, entry-level network attached storage (NAS) appliances, secure routers, smart-grid substation concentrators, and point-of-sale terminals that require deterministic networking and low-latency serial interfaces.
When designing with the P1010NSN5HFA, careful PCB layout is essential - the 425-ball TEPBGA requires microvia or HDI PCB technology, and the DDR3 memory traces must be length-matched within the controller's tolerance window. Use NXP's BSP and CodeWarrior toolchain; the part is supported in mainstream Linux BSPs (mainline and NXP BSP).
This page synthesizes current distributor stock, drop-in package-compatible alternatives, and practical board-design guidance that go beyond the manufacturer datasheet alone.
直接替換替代品，適用於 P1010NSN5HFA — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： P1010NSN5HFA （相同外形與佔位） — 差異在於 Operating Temperature, Package, SATA, USB, Memory Controller.
P1010NSE5HHB
✅ 直接替換📋 參考替代品（不在目錄中）
P1014NSN5HFA
✅ 直接替換聯絡詢價
查看資料表 →P1014NXN5DFA
✅ 直接替換聯絡詢價
查看資料表 →P1010NXN5HHB
✅ 直接替換📋 參考替代品（不在目錄中）
P1010NSN5HFB
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →P1010NSN5HFA 最大額定值與電氣特性
| Processor Series | QorIQ P1 |
| Core Architecture | Power Architecture e500v2 |
| Number of Cores | 1 |
| Core Frequency | 800 MHz |
| DDR Bus Frequency | 667 MHz |
| Process Technology | 45 nm |
| 封裝 | 425-TEPBGA I (19x19 mm) |
| 工作溫度 | 0 °C to +105 °C |
| Typical Power Dissipation | 1.1 W (typ, as low as 1.1 W per NXP product page) |
| Memory Controller | DDR3 with ECC |
| Ethernet Interfaces | 2x Gigabit Ethernet |
| PCI Express | PCIe Gen1/Gen2 |
| SATA | SATA II controller integrated |
| USB | USB 2.0 with PHY |
| Security | Trusted Boot / Security Engine |
| RoHS 狀態 | RoHS Compliant |
| Lead-Free Status | Lead Free |
| 安裝類型 | Surface Mount (BGA) |
P1010NSN5HFA 腳位配置
| 腳位 A1 | GND — Ground reference |
| 腳位 B12 | VDD — Core supply voltage |
| 腳位 C18 | DDR3_DQ0 — DDR3 data lane 0 |
| 腳位 G5 | PCIe_TX0_P — PCIe transmit lane 0 positive |
| 腳位 H7 | SATA0_TX_P — SATA 0 transmit positive |
| 腳位 K10 | USB1_DP — USB 2.0 data plus |
| 腳位 L15 | SGMII1_TX_P — GbE SGMII lane 1 transmit positive |
| 腳位 N3 | GPIO0 — General-purpose I/O 0 |
| 腳位 R12 | TDM_RXD — TDM receive data |
| 腳位 T20 | JTAG_TDO — JTAG test data out |
典型應用
P1010NSN5HFA 適用於 6 應用s: IP Camera / Surveillance Encoder, Industrial Robotics Controller, Entry-Level Network Attached Storage (NAS), Factory Automation Gateway, Secure Router / VPN Concentrator, Smart-Grid Substation Concentrator.
IP Camera / Surveillance Encoder
The P1010NSN5HFA's 800 MHz e500v2 core, dual integrated Gigabit Ethernet ports, SATA II controller, and hardware-accelerated trusted boot make it ideal as the main SoC in PoE-powered IP cameras. The 1.1 W typical power dissipation enables fanless enclosures, while the integrated security engine provides tamper-resistant boot for surveillance deployments. Unlike multi-chip PowerQUICC designs, the P1010 replaces the host CPU, Ethernet MACs, and SATA controller with a single chip, simplifying BOM and PCB layout for compact camera modules.
推薦
Industrial Robotics Controller
In industrial robotics, the P1010NSN5HFA delivers deterministic single-core compute performance with real-time Linux (PREEMPT_RT or Xenomai) for motion control loops. The four TDM/HDLC ports connect to legacy fieldbus peripherals, while PCIe and GbE interface with machine vision cameras and PLC networks. The 0 °C to +105 °C operating range covers most factory floor environments, and the integrated DDR3 controller with ECC provides memory integrity for safety-critical motion sequences.
推薦
Entry-Level Network Attached Storage (NAS)
The P1010NSN5HFA's integrated SATA II controller, dual GbE (for link aggregation / failover), and PCIe for additional NICs make it well-suited as the SoC for entry-level NAS appliances with 2-4 drive bays. Hardware RAID offload and the e500v2 core's signal processing extensions accelerate file-system operations, while trusted boot protects stored data at rest. The 800 MHz CPU is sufficient for consumer/small-business throughput targets where multi-core P2/P3 series would be over-spec.
推薦
Factory Automation Gateway
Factory automation gateways using the P1010NSN5HFA can aggregate multiple fieldbus protocols (Modbus, Profibus, EtherNet/IP) via the integrated TDM/HDLC ports and GbE interfaces. The hardware virtualization extensions of the e500v2 core allow partitioning of real-time control and IT connectivity on a single SoC, reducing gateway footprint and cost. The 425-TEPBGA I package and industrial temperature rating make the P1010 suitable for control cabinet mounting with extended thermal headroom.
推薦
Secure Router / VPN Concentrator
Small-business routers and VPN concentrators benefit from the P1010NSN5HFA's hardware-accelerated trusted boot, GbE interfaces, and PCIe for additional WAN NICs. The e500v2 core provides sufficient compute for IPSec/AES encryption at small-site throughput, while the integrated security engine protects the boot flow and configuration store. The 1.1 W typical power dissipation keeps wall-mount and PoE-powered router designs within thermal limits without active cooling.
推薦
Smart-Grid Substation Concentrator
In smart-grid substation concentrators, the P1010NSN5HFA aggregates data from multiple IEC 61850 / DNP3 field devices over GbE and serial ports, with trusted boot ensuring substation network integrity. The industrial 0-105 °C operating range, ECC-protected DDR3, and hardware-assisted encryption make the P1010 suitable for utility-grade installations. The single 800 MHz core is sufficient for substation concentrator workloads where deterministic latency and security matter more than raw throughput.
推薦
推薦產品摘要
工程參考資料，適用於 P1010NSN5HFA — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | P1010NSE5HHB | P1014NSN5HFA | P1014NXN5DFA | P1010NXN5HHB | P1010NSN5HFB |
|---|---|---|---|---|---|---|
| Package | 425-TEPBGA I (19x19 mm) | 425-TEPBGA I (19x19 mm) - same | 425-TEPBGA I (19x19 mm) - same | 425-TEPBGA I (19x19 mm) - same | 425-TEPBGA I (19x19 mm) - same | 425-TEPBGA I (19x19 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Processor Series | QorIQ P1 | QorIQ P1 | QorIQ P1 | QorIQ P1 | QorIQ P1 | QorIQ P1 |
| Core Architecture | Power Architecture e500v2 | Power Architecture e500v2 | Power Architecture e500v2 | Power Architecture e500v2 | Power Architecture e500v2 | Power Architecture e500v2 |
| Number of Cores | 1 | 1 | 1 | 1 | 1 | 1 |
| RoHS Status | RoHS Compliant | RoHS Compliant | RoHS Compliant | RoHS Compliant | RoHS Compliant | RoHS Compliant |
主要差異化特點
- Single-chip integration replacing multi-chip PowerQUICC designs (對比P1014NXN5DFA)
- Lower power envelope for fanless endpoint designs (對比P1014NSN5HFA)
- Trusted boot with hardware security engine (對比Older PowerQUICC II/III families)
設計說明
The 425-ball TEPBGA I (19x19 mm) package requires HDI PCB technology with microvias for breakout routing. Per NXP QorIQ P1 layout guidelines, DDR3 traces must be length-matched within the controller's tolerance (typically within 25 mil on the same byte lane) and routed on inner layers with reference planes on both sides to maintain signal integrity at 667 MHz DDR operation.
Although the P1010NSN5HFA typically dissipates 1.1 W, peak workloads (DDR3 bursts, PCIe Gen2 link training, security engine operations) can push junction temperature higher. Use NXP's power estimator to validate thermal design; in sealed enclosures, derate to 90% of Tj max and consider a small copper heat-spreader if the SoC shares a PCB with high-power devices.
Do not confuse the P1010 with the pin-compatible P1014 family - although they share the same 425-TEPBGA I footprint, the P1014 has larger cache and a different peripheral mix, so firmware boots only on the matched part. When sourcing replacements, verify the full NXP ordering code (e.g. P1010NSN5HFA vs P1014NSN5HFA) and validate with NXP's part-number decoder before committing to a BOM change.
合規資訊
RoHS compliant and lead-free per DigiKey listing. AEC-Q100 not applicable (communications processor, not automotive-grade MCU). Halogen-free status not explicitly stated in available data.
