PCA9641BSHP - 2-Channel I2C Master Arbiter | NXP
MPN: PCA9641BSHP ✓ 啟用中PCA9641BSHP 概覽
An I2C controller arbiter is an interface-management IC that coordinates access to a shared two-wire bus. It belongs to the hierarchy of I2C interface devices, serial bus controllers, bus arbiters, and interface ICs. Unlike a conventional I2C multiplexer, which routes one controller toward one of several downstream buses, the PCA9641 permits two controllers to share a common downstream bus while managing simultaneous access and arbitration timing.
The PCA9641BSHP is intended for dual-controller architectures requiring deterministic bus ownership. Its central function is to select one master when both masters request the bus, allow the selected master to complete its transfer uninterrupted, and subsequently let the other master gain control. This behavior supports systems in which independent controllers, such as a processor and an auxiliary controller, must coexist on one I2C bus without placing both on the bus simultaneously.
The 16-HVQFN construction supports compact PCB layouts while its exposed thermal pad provides a means for heat spreading and, where required, electrical connection to the ground reference specified by the manufacturer. Because the exposed-pad connection and layout requirements are package- and board-specific, PCB designers should follow the land pattern and thermal guidance in the NXP manufacturer datasheet rather than treating the pad as an unrestricted signal terminal.
Typical uses include industrial control modules, embedded automation boards, dual-processor equipment, sensor systems, and communication equipment in which two embedded controllers must arbitrate access to one shared I2C segment. The arbiter role is particularly valuable when independent control loops or operating systems could otherwise generate overlapping bus activity. It is also suitable for bus-isolation architectures where downstream devices must not see simultaneous controller commands.
Design consideration: arbitration timing, bus timeout behavior, pull-up placement, and controller compatibility determine whether the system remains reliable during simultaneous requests. Follow the NXP datasheet for master arbitration timing, reset behavior, electrical limits, and the recommended exposed-pad layout. Confirm that both connected controllers observe the intended bus ownership and release behavior before integrating the device into a safety- or uptime-critical system.
This product page combines the verified NXP device description, package information, distributor records, technical application guidance, and a strict drop-in-replacement assessment. It distinguishes confirmed characteristics from parameters that require confirmation from the manufacturer datasheet, helping engineers evaluate the PCA9641BSHP without treating unverified electrical assumptions as design facts.
直接替換替代品,適用於 PCA9641BSHP — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此產品無可直接替換的替代品。
申請替代品PCA9641BSHP 規格
| Product Type | 2-channel I2C controller arbiter and demultiplexer |
| Channel Count | 2 channels |
| Bus Topology | 2-to-1 I2C controller demultiplexer |
| Arbitration Function | Supported; one winning controller is selected |
| Simultaneous Master Handling | Supported for dual-controller I2C-bus applications |
| 工作溫度範圍 | -40 °C to +85 °C |
| 封裝 | 16-pin HVQFN with exposed pad |
| Package Dimensions | 3 mm × 3 mm |
| 安裝類型 | Surface mount |
| Packaging | Tape and reel |
| 腳位數 | 16 pins |
PCA9641BSHP 3 mm × 3 mm 腳位配置指南
PCA9641BSHP(3 mm × 3 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: PCA9641BSHP.
請參閱 資料表 以查看完整腳位配置。
典型應用
PCA9641BSHP 適用於 6 應用s: Dual-Processor Industrial Control, Robotics Sensor Coordination, Smart Sensor Hub, Communication Equipment Control, Automotive Accessory Controller, Test and Measurement Controller.
Dual-Processor Industrial Control
The PCA9641BSHP fits industrial controller assemblies in which a main processor and an auxiliary controller may both address sensors or actuators through one shared I2C segment. Its arbitration function selects a winning controller during a simultaneous request and allows that controller to complete the transaction without interruption. The 16-pin HVQFN body also preserves board area in compact control modules. Integration still requires validation of master timing, reset sequencing, pull-up placement, and the exposed-pad layout specified by NXP.
推薦
Robotics Sensor Coordination
The PCA9641BSHP can coordinate a primary robot controller and a secondary motion or safety controller sharing an I2C sensor network. When both controllers request the bus simultaneously, the arbiter selects one winner and prevents overlapping commands from reaching the shared segment. This is useful where actuator and sensor state must remain deterministic despite asynchronous controller activity. The device should be placed close to the shared bus branch, with pull-ups and routing checked against the electrical and timing conditions in the manufacturer datasheet.
推薦
Smart Sensor Hub
The PCA9641BSHP is applicable to smart sensor hubs where two embedded controllers need coordinated access to a common sensor bus. Its 2-to-1 controller demultiplexer and arbitration function separate bus ownership from downstream access, reducing the likelihood that simultaneous controller traffic will collide. The 3 mm × 3 mm HVQFN package supports compact sensor assemblies, while the exposed pad requires the prescribed PCB footprint and thermal treatment. Firmware must account for the losing controller being unable to use the shared bus until ownership changes.
推薦
Communication Equipment Control
The PCA9641BSHP supports communication modules in which a network processor and a configuration controller share an I2C management bus. The arbitration function helps maintain deterministic command delivery if both controllers become active together, while the compact HVQFN package limits the footprint in dense line cards and edge equipment. Designers should verify cable-length limits, bus capacitance, pull-up values, reset behavior, and arbitration timing for the final topology. The device does not replace protocol isolation or level translation when those functions are required.
推薦
Automotive Accessory Controller
The PCA9641BSHP can manage access to a shared I2C bus in automotive accessory or body electronics modules when two controllers require coordinated ownership. Its -40 °C to +85 °C operating range covers industrial-temperature applications, although automotive qualification requirements must be checked separately for the exact ordered device. The small 16-pin HVQFN package is useful in dense control units. Firmware and hardware validation should include simultaneous startup, bus recovery after reset, and fault behavior when one controller becomes unresponsive.
推薦
Test and Measurement Controller
The PCA9641BSHP is appropriate for test and measurement instruments that use one I2C bus to connect a main controller with an acquisition, calibration, or front-end controller. Arbitration gives the active device exclusive use of the shared bus during overlapping commands, supporting predictable test sequencing. Its compact package fits instrument control boards without requiring a large demultiplexer footprint. System validation should include worst-case bus timing, timeout behavior, firmware retry strategies, and the ground connection required for the HVQFN exposed pad.
推薦
推薦產品摘要
工程參考資料,適用於 PCA9641BSHP — 比較、設計指引及合規資訊。
選型指南
設計說明
Do not treat a generic 16-pin QFN multiplexer as a functional replacement for the PCA9641BSHP. The PCA9641 arbitrates simultaneous requests from two controllers, while parts such as the PCA9557BS,118 provide an 8-bit I/O port and PCA9500BS provides a different I2C or SMBus interface. Before substitution, compare every pin, supply limits, reset behavior, arbitration timing, input thresholds, output contention behavior, and exposed-pad requirements.
Use the exact 16-pin HVQFN land pattern and exposed-pad treatment from the NXP package drawing. Place the device near the shared downstream bus branch and route controller inputs so their physical channel assignment matches the intended arbitration design. Keep the exposed-pad copper and via arrangement consistent with the manufacturer's layout guidance, and review how the pad is connected to ground on the final board stack-up.
Validate pull-up resistance, bus capacitance, rise and fall times, and the worst-case timing when both controllers request access. The arbitration function controls ownership but does not remove the need for a compliant I2C physical layer. Use oscilloscope measurements during simultaneous startup and controller reset tests, and ensure firmware cannot assume that an immediate second transfer will always be accepted.
合規資訊
The operating temperature range is stated, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was confirmed. AEC-Q100 qualification is not applicable to the standard commercial part based on the verified ordering information.