PCA9661B - 3.3V I2C Bus Controller | NXP | LQFP-48
MPN: PCA9661B ✗ 停產PCA9661B 概覽
An I2C-bus controller is an interface IC that manages transactions between a parallel processor or bus master and devices connected through the two-wire I2C interface. In the broader semiconductor hierarchy, the PCA9661B belongs to the I2C controller class, which falls under interface controllers and then general-purpose interface ICs. Its role is to translate parallel data, control signaling, and bus timing into serialized I2C transfers for displays, sensors, memory devices, communications modules, and other peripheral ICs.
NXP describes the PCA9661 as an advanced, fourth-generation, single-leader-mode bus controller. The B revision is identified in the product information as a single-master or single-leader I2C controller. Its architecture is intended to support dense systems where a processor-side parallel interface must service multiple I2C destinations efficiently. Parallel-to-serial bus management can reduce repetitive software transactions by centralizing addressing, control, and status handling in dedicated hardware.
The 3.3 V operating supply matches many contemporary embedded processors, application processors, programmable logic devices, and communication controllers. This makes the PCA9661B useful in industrial controllers, test equipment, embedded computing platforms, communications infrastructure, and data-acquisition systems that already operate from a 3.3 V rail. Designers should confirm signal levels, timing limits, supported operating modes, and exact register behavior against the manufacturer datasheet before finalizing a new design.
The 48-LQFP package exposes 48 leads, but its 1.4 mm package height does not by itself determine minimum PCB pad geometry. Follow the NXP land-pattern and stencil recommendations, including exposed-pad and soldering details shown for the selected orderable variant. Account for signal propagation between the parallel interface and the I2C pins, and place pull-up and bus-capacitance components where they can maintain a short return path.
NXP marks the PCA9661B as not recommended for new designs and identifies PCA9665APW as its recommended replacement. Existing installations may continue to use the PCA9661B for maintenance or design continuity, but new products should evaluate the recommended NXP successor and confirm whether its package, pinout, registers, voltage limits, timing, and thermal characteristics permit a direct PCB substitution. The PCA9665APW is not represented here as a drop-in alternative because the available product information does not establish pin-to-pin and package equivalence.
This page organizes the verified product identity, lifecycle guidance, electrical limits, package details, design considerations, replacement analysis, and application guidance. It distinguishes confirmed manufacturer information from parameters that still require direct review of the datasheet, helping engineers separate verified device facts from assumptions before schematic capture, PCB layout, or production sourcing.
直接替換替代品,適用於 PCA9661B — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此產品無可直接替換的替代品。
申請替代品PCA9661B 規格
| Device Type | I2C parallel-interface bus controller |
| Bus Interface | I2C |
| Operating Mode | Single-leader mode |
| 供應電壓 | 3.3 V |
| I2C Channel Count | 1 channel |
| 工作溫度範圍 | -40°C to 85°C |
| 封裝 | 48-LQFP |
| Package Body Size | 7 mm x 7 mm |
| Package Height | 1.40 mm |
PCA9661B 1.40 mm 腳位配置指南
PCA9661B(1.40 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: PCA9661B.
請參閱 資料表 以查看完整腳位配置。
典型應用
PCA9661B 適用於 6 應用s: Industrial Embedded Controllers, Data Acquisition Systems, Communications and Network Equipment, Instrumentation and Test Equipment, Display and Control Panels, Legacy Platform Maintenance.
Industrial Embedded Controllers
The PCA9661B fits industrial embedded controllers that need to connect a parallel host processor to I2C sensors, memory, display controllers, and expansion devices. Its 3.3 V supply aligns with common embedded logic levels, while the -40°C to 85°C listed operating range supports temperature-controlled equipment. The dedicated I2C controller can reduce repetitive software work by handling serialized bus transactions through hardware. However, NXP marks the PCA9661B as not recommended for new designs, so a new industrial platform should begin with the PCA9665APW and validate whether its interface, timing, and pinout meet the system requirements.
推薦
Data Acquisition Systems
Data-acquisition equipment can use the PCA9661B when multiple analog-to-digital converters, sensors, memory devices, or communication modules share an I2C bus but the system processor connects through a parallel interface. The single-channel controller provides a hardware-managed path for data-intensive I2C transfers and operates from a 3.3 V supply. Designers should calculate total bus capacitance, place pull-up resistors appropriately, and verify supported clock rate and signal timing. For newly created measurement platforms, evaluate PCA9665APW rather than committing to the legacy PCA9661B lifecycle position.
推薦
Communications and Network Equipment
The PCA9661B is applicable to communication controllers, interface modules, and embedded network equipment where a parallel processor must manage I2C peripherals such as EEPROMs, PHYs, transceivers, status monitors, or configuration devices. A hardware I2C controller can offload bus serialization from the main processor and support deterministic access to multiple addresses. The 3.3 V operating supply is consistent with many communication ICs, but level compatibility must be checked pin by pin. New networking products should use the manufacturer-recommended PCA9665APW and confirm timing, interrupt, addressing, and software-driver differences during migration.
推薦
Instrumentation and Test Equipment
Laboratory and industrial instrumentation can use the PCA9661B to bridge a parallel control processor to I2C-managed converters, EEPROMs, display drivers, calibration devices, or status registers. The 7 mm by 7 mm 48-LQFP package provides a conventional surface-mount assembly option, while the -40°C to 85°C range supports many measurement environments. Layout must preserve signal integrity on the clock and data lines and comply with the required pull-up network. Because the part is not recommended for new designs, instrument makers should prototype the PCA9665APW and perform a complete register and timing comparison before production release.
推薦
Display and Control Panels
Display-intensive control systems can employ the PCA9661B when a host processor accesses display controllers, touch controllers, indicators, configuration memories, or other I2C peripherals through a parallel interface. Consolidating serial-bus control in an interface IC can reduce host-level transaction overhead and support multiple addressed destinations. The 3.3 V device is suitable for many mixed-signal control boards, although I2C pull-up voltage selection and rise-time margin require careful review. New human-machine interfaces should favor the recommended PCA9665APW and confirm display-driver compatibility, timing margins, and software initialization sequences.
推薦
Legacy Platform Maintenance
The PCA9661B remains applicable to maintenance, repair, and lifecycle-extension programs for equipment already built around its parallel interface and 48-LQFP footprint. In this setting, preserving the approved controller can avoid board respin and software disruption when qualification, availability, and sourcing conditions are satisfactory. Engineers should document the device's not-recommended-for-new-designs status and define an obsolescence plan. A transition to PCA9665APW can be evaluated through schematic, firmware, timing, and mechanical comparisons, with the final decision based on total redesign risk rather than device identity alone.
推薦
推薦產品摘要
工程參考資料,適用於 PCA9661B — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | PCA9665APW |
|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors |
| Lifecycle Recommendation | Not recommended for new designs | Manufacturer-designated replacement |
主要差異化特點
- Clear manufacturer lifecycle direction (對比PCA9665APW)
- Established fourth-generation controller positioning (對比PCA9665APW)
- Defined package and temperature identity (對比PCA9665APW)
設計說明
Route the parallel interface and I2C clock/data nets as short, referenced paths on the PCB. Place pull-up resistors for SDA and SCL close to the bus devices with the shortest practical return connection to the supply or ground plane. Confirm the maximum supported bus rate and total bus capacitance in the manufacturer datasheet, then use scope measurements at the slowest corner to verify rise time and signal margins.
Do not treat the manufacturer-named PCA9665APW as a drop-in replacement without a pin-by-pin comparison. Check package dimensions, lead pitch, exposed-pad arrangement, supply limits, clock timing, address handling, interrupt behavior, and software registers. If any function differs, treat the change as a redesign rather than a simple component substitution and update schematic, layout, firmware, and validation tests.
Use the exact NXP package drawing and recommended land pattern for the selected orderable part. A 48-LQFP body measuring 7 mm by 7 mm does not establish lead pitch, pin numbering, or exposed-pad requirements by itself. Check assembly-process capability, stencil aperture recommendations, solder-mask clearance, and the pin-1 orientation before releasing artwork.
Operate the PCA9661B from a stable 3.3 V rail and verify the host and I2C signal thresholds against that supply. Decouple the device according to the manufacturer application guidance, including the required input and output capacitance values. During replacement planning, compare the successor's supply range and power sequencing requirements rather than assuming identical behavior.
合規資訊
The verified product summaries do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations for PCA9661B.