NXP Semiconductors

PCA9661B - 3.3V I2C Bus Controller | NXP | LQFP-48

MPN: PCA9661B ✗ پایان تولید
3.3 V Vdss 48-LQFP Package
حداقل سفارش: 1 |

PCA9661B نمای کلی

The NXP Semiconductors PCA9661B is a 3.3 V I2C parallel-interface bus controller designed for data-intensive I2C transfers. It is offered in a 48-LQFP package measuring 7 mm by 7 mm and operates across the -40°C to 85°C temperature range. The device provides one I2C-bus channel and uses parallel interface logic to connect a host-side parallel bus with external serial peripherals.

An I2C-bus controller is an interface IC that manages transactions between a parallel processor or bus master and devices connected through the two-wire I2C interface. In the broader semiconductor hierarchy, the PCA9661B belongs to the I2C controller class, which falls under interface controllers and then general-purpose interface ICs. Its role is to translate parallel data, control signaling, and bus timing into serialized I2C transfers for displays, sensors, memory devices, communications modules, and other peripheral ICs.

NXP describes the PCA9661 as an advanced, fourth-generation, single-leader-mode bus controller. The B revision is identified in the product information as a single-master or single-leader I2C controller. Its architecture is intended to support dense systems where a processor-side parallel interface must service multiple I2C destinations efficiently. Parallel-to-serial bus management can reduce repetitive software transactions by centralizing addressing, control, and status handling in dedicated hardware.

The 3.3 V operating supply matches many contemporary embedded processors, application processors, programmable logic devices, and communication controllers. This makes the PCA9661B useful in industrial controllers, test equipment, embedded computing platforms, communications infrastructure, and data-acquisition systems that already operate from a 3.3 V rail. Designers should confirm signal levels, timing limits, supported operating modes, and exact register behavior against the manufacturer datasheet before finalizing a new design.

The 48-LQFP package exposes 48 leads, but its 1.4 mm package height does not by itself determine minimum PCB pad geometry. Follow the NXP land-pattern and stencil recommendations, including exposed-pad and soldering details shown for the selected orderable variant. Account for signal propagation between the parallel interface and the I2C pins, and place pull-up and bus-capacitance components where they can maintain a short return path.

NXP marks the PCA9661B as not recommended for new designs and identifies PCA9665APW as its recommended replacement. Existing installations may continue to use the PCA9661B for maintenance or design continuity, but new products should evaluate the recommended NXP successor and confirm whether its package, pinout, registers, voltage limits, timing, and thermal characteristics permit a direct PCB substitution. The PCA9665APW is not represented here as a drop-in alternative because the available product information does not establish pin-to-pin and package equivalence.

This page organizes the verified product identity, lifecycle guidance, electrical limits, package details, design considerations, replacement analysis, and application guidance. It distinguishes confirmed manufacturer information from parameters that still require direct review of the datasheet, helping engineers separate verified device facts from assumptions before schematic capture, PCB layout, or production sourcing.

جایگزین‌های drop-in برای PCA9661B — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

هیچ جایگزین مستقیمی برای این محصول موجود نیست.

درخواست جایگزین

PCA9661B مشخصات

Device Type I2C parallel-interface bus controller
Bus Interface I2C
Operating Mode Single-leader mode
ولتاژ تغذیه 3.3 V
I2C Channel Count 1 channel
محدوده دمای کاری -40°C to 85°C
بسته‌بندی 48-LQFP
Package Body Size 7 mm x 7 mm
Package Height 1.40 mm

راهنمای پیکربندی پین PCA9661B 1.40 mm

پیکربندی پین برای PCA9661B (پکیج 1.40 mm). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 1.40 mm برای PCA9661B

داده پین‌آوت تفصیلی موجود نیست برای PCA9661B.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

PCA9661B مناسب است برای 6 کاربردs: Industrial Embedded Controllers, Data Acquisition Systems, Communications and Network Equipment, Instrumentation and Test Equipment, Display and Control Panels, Legacy Platform Maintenance.

🏭

Industrial Embedded Controllers

The PCA9661B fits industrial embedded controllers that need to connect a parallel host processor to I2C sensors, memory, display controllers, and expansion devices. Its 3.3 V supply aligns with common embedded logic levels, while the -40°C to 85°C listed operating range supports temperature-controlled equipment. The dedicated I2C controller can reduce repetitive software work by handling serialized bus transactions through hardware. However, NXP marks the PCA9661B as not recommended for new designs, so a new industrial platform should begin with the PCA9665APW and validate whether its interface, timing, and pinout meet the system requirements.

🖥️

Data Acquisition Systems

Data-acquisition equipment can use the PCA9661B when multiple analog-to-digital converters, sensors, memory devices, or communication modules share an I2C bus but the system processor connects through a parallel interface. The single-channel controller provides a hardware-managed path for data-intensive I2C transfers and operates from a 3.3 V supply. Designers should calculate total bus capacitance, place pull-up resistors appropriately, and verify supported clock rate and signal timing. For newly created measurement platforms, evaluate PCA9665APW rather than committing to the legacy PCA9661B lifecycle position.

🌐

Communications and Network Equipment

The PCA9661B is applicable to communication controllers, interface modules, and embedded network equipment where a parallel processor must manage I2C peripherals such as EEPROMs, PHYs, transceivers, status monitors, or configuration devices. A hardware I2C controller can offload bus serialization from the main processor and support deterministic access to multiple addresses. The 3.3 V operating supply is consistent with many communication ICs, but level compatibility must be checked pin by pin. New networking products should use the manufacturer-recommended PCA9665APW and confirm timing, interrupt, addressing, and software-driver differences during migration.

🔧

Instrumentation and Test Equipment

Laboratory and industrial instrumentation can use the PCA9661B to bridge a parallel control processor to I2C-managed converters, EEPROMs, display drivers, calibration devices, or status registers. The 7 mm by 7 mm 48-LQFP package provides a conventional surface-mount assembly option, while the -40°C to 85°C range supports many measurement environments. Layout must preserve signal integrity on the clock and data lines and comply with the required pull-up network. Because the part is not recommended for new designs, instrument makers should prototype the PCA9665APW and perform a complete register and timing comparison before production release.

📺

Display and Control Panels

Display-intensive control systems can employ the PCA9661B when a host processor accesses display controllers, touch controllers, indicators, configuration memories, or other I2C peripherals through a parallel interface. Consolidating serial-bus control in an interface IC can reduce host-level transaction overhead and support multiple addressed destinations. The 3.3 V device is suitable for many mixed-signal control boards, although I2C pull-up voltage selection and rise-time margin require careful review. New human-machine interfaces should favor the recommended PCA9665APW and confirm display-driver compatibility, timing margins, and software initialization sequences.

🔧

Legacy Platform Maintenance

The PCA9661B remains applicable to maintenance, repair, and lifecycle-extension programs for equipment already built around its parallel interface and 48-LQFP footprint. In this setting, preserving the approved controller can avoid board respin and software disruption when qualification, availability, and sourcing conditions are satisfactory. Engineers should document the device's not-recommended-for-new-designs status and define an obsolescence plan. A transition to PCA9665APW can be evaluated through schematic, firmware, timing, and mechanical comparisons, with the final decision based on total redesign risk rather than device identity alone.

خلاصه محصولات پیشنهادی

PCA9665APW Manufacturer-designated replacement for new-design evaluation استفاده‌شده در: Industrial Embedded Controllers, Data Acquisition Systems, Communications and Network Equipment, Instrumentation and Test Equipment, Display and Control Panels, Legacy Platform Maintenance
What is the NXP PCA9661B?
The NXP PCA9661B is a 3.3 V, single-leader-mode I2C parallel-interface bus controller with one I2C channel in a 48-LQFP package. According to the NXP product page, it is an advanced fourth-generation bus controller intended for data-intensive I2C transfers. Its principal function is to connect a parallel host-side interface to I2C peripherals while offloading serial-bus control from general-purpose host software.
What are the key specifications of PCA9661B that engineers should know?
The PCA9661B is a 3.3 V I2C bus controller with one I2C channel, single-leader operation, and a 7 mm by 7 mm 48-LQFP package rated for -40°C to 85°C. NXP identifies the PCA9661 as a fourth-generation controller designed for data-intensive transfers. Maximum bus frequency, parallel-interface width, address count, and detailed timing limits must be confirmed in the manufacturer datasheet for the exact orderable device.
Is PCA9661B suitable for industrial embedded control systems?
The PCA9661B is suitable for many 3.3 V embedded-control designs because its listed operating range is -40°C to 85°C and its LQFP package supports conventional board-assembly processes. NXP identifies the device as not recommended for new designs, so an industrial project should use the recommended PCA9665APW unless maintaining an existing platform. Confirm the successor's electrical, timing, pinout, and lifecycle requirements before releasing new production hardware.
Why is PCA9661B marked not recommended for new designs?
NXP marks the PCA9661B as not recommended for new designs and explicitly identifies PCA9665APW as the replacement part. This status generally means the manufacturer directs new development toward the successor rather than the older device. Existing products may still be maintained, but new designs should review the recommended replacement and perform an electrical, timing, register, package, and PCB compatibility review before migration.
What is the recommended replacement for PCA9661B?
NXP recommends the PCA9665APW as the replacement for the PCA9661B. The manufacturer product page explicitly identifies that successor. It should not automatically be treated as a pin-for-pin drop-in replacement because the available product information does not establish matching package dimensions, lead arrangement, electrical limits, or register compatibility. Use the PCA9665APW data for redesign and verify the mechanical drawing and pin functions before substitution.
Can PCA9665APW replace PCA9661B without a PCB change?
Do not assume that PCA9665APW can replace PCA9661B without a PCB change. NXP identifies PCA9665APW as the recommended replacement, but the verified product information does not demonstrate that it uses the same 48-LQFP footprint or preserves every PCA9661B pin function. Compare the two datasheets for pinout, supply range, I2C timing, interface width, addresses, interrupt behavior, and application configuration before approving a drop-in substitution.
What can replace PCA9661B?
The manufacturer-designated replacement for PCA9661B is the NXP PCA9665APW. It is the only candidate named directly in the verified NXP product information, so it is the appropriate starting point for a redesign review. A true drop-in replacement would additionally require the same package, pin-to-pin compatibility, compatible signal levels, and matching timing or software behavior; those conditions are not established by the available product summaries.
PCA9661B vs PCA9665APW - which is better for a new design?
PCA9665APW is the better starting point for a new design because NXP specifically recommends it as the successor to the not-recommended-for-new-designs PCA9661B. PCA9661B remains relevant for maintenance of existing platforms and for continuity where organizational sourcing rules require it. The final choice depends on whether the new design requires a PCB change, register adaptation, timing changes, or a different package.
What is the difference between PCA9661B and PCA9665APW?
The principal confirmed difference is lifecycle direction: NXP identifies PCA9665APW as the replacement for the not-recommended-for-new-designs PCA9661B. Detailed differences in pinout, package, maximum clock frequency, address count, electrical limits, and register behavior are not stated in the verified product summaries. Compare the current datasheets and package drawings to quantify those differences before selecting either device for new hardware.
When should I choose PCA9661B over PCA9665APW?
Choose PCA9661B only when maintaining an existing product, reproducing an established assembly, or meeting an organizational requirement that specifically calls for the legacy device. For new industrial, consumer, or communications designs, PCA9665APW is generally preferable because it is the manufacturer-named successor. Existing software and PCB compatibility may justify retaining PCA9661B, but its not-recommended-for-new-designs status should be documented.
Where can I download the PCA9661B datasheet PDF?
The PCA9661B datasheet can be accessed through the NXP product page at https://www.nxp.com/products/PCA9661B and through the datasheet link listed on this page at https://www.datasheets.com/nxp/pca9661b. Use the manufacturer copy as the controlling document for pin functions, timing, electrical limits, register definitions, and package drawings. The datasheet repository is useful for access, while the NXP document should govern engineering decisions.
Where can I find the PCA9661B pinout?
The PCA9661B pinout is defined in the pin-description and package-outline sections of the manufacturer datasheet. The device uses a 48-LQFP package, but the verified product summaries do not enumerate the 48 pin names or confirm whether the B revision includes an exposed pad. Use the pin-description table from the exact datasheet revision before assigning PCB nets or treating any substituted part as pin compatible.
What is the operating voltage of PCA9661B?
The listed operating supply voltage for PCA9661B is 3.3 V. This makes the controller suitable for systems whose host-side logic operates on a 3.3 V rail. Before implementation, verify the recommended operating range, absolute maximum ratings, input thresholds, output levels, and power-up behavior in the manufacturer datasheet, especially when interfacing the device to another logic family.
Where can I buy PCA9661B online?
The PCA9661B can be requested through the Request a Quote form on this XAIPART page, which should be used for current pricing, stock, minimum order quantity, and lead time. NXP identifies the device as not recommended for new designs and recommends the PCA9665APW, so buyers should confirm whether legacy-part procurement is acceptable. Current commercial terms should be obtained through the quote request rather than assumed from historical listings.
What is the price of PCA9661B?
Current PCA9661B pricing is not displayed as a fixed value because commercial terms can change with quantity, availability, condition, and sourcing status. Use the Request a Quote form on this page for the unit-price schedule, minimum order quantity, and lead time. Because NXP labels the device not recommended for new designs, include the proposed annual volume and product lifecycle requirements in the request.
What is the lead time for PCA9661B?
The current lead time for PCA9661B must be confirmed through the Request a Quote form on this page because no reliable quantity-specific lead time appears in the verified product information. Provide the required order quantity, packaging preference, target date, and production horizon. For a new design, also request the lifecycle status of the manufacturer-recommended PCA9665APW to avoid creating a second sourcing risk.

داده‌های مرجع مهندسی برای PCA9661B — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose PCA9661B when maintaining an existing 48-LQFP platform, reproducing a qualified assembly, or meeting a documented sourcing requirement for the legacy controller. Its not-recommended-for-new-designs status makes it less attractive for new industrial, communication, test, or consumer products. Choose PCA9665APW as the starting point for a new design because NXP explicitly identifies it as the replacement. Do not assume it is PCB drop-in compatible: verify package geometry, pinout, electrical limits, clock timing, register behavior, and software initialization. If the comparison shows functional but mechanical or timing differences, budget for a board and firmware redesign. For a straight board substitution, only approve PCA9665APW after its exact orderable variant has passed a pin-to-pin and timing comparison against the installed PCA9661B.

مقایسه با جایگزین‌ها

پارامتر این محصول PCA9665APW
Brand NXP Semiconductors NXP Semiconductors
Lifecycle Recommendation Not recommended for new designs Manufacturer-designated replacement

تفاوت‌های کلیدی

  • Clear manufacturer lifecycle direction (در مقابلPCA9665APW)
  • Established fourth-generation controller positioning (در مقابلPCA9665APW)
  • Defined package and temperature identity (در مقابلPCA9665APW)

یادداشت‌های طراحی

Route the parallel interface and I2C clock/data nets as short, referenced paths on the PCB. Place pull-up resistors for SDA and SCL close to the bus devices with the shortest practical return connection to the supply or ground plane. Confirm the maximum supported bus rate and total bus capacitance in the manufacturer datasheet, then use scope measurements at the slowest corner to verify rise time and signal margins.

Do not treat the manufacturer-named PCA9665APW as a drop-in replacement without a pin-by-pin comparison. Check package dimensions, lead pitch, exposed-pad arrangement, supply limits, clock timing, address handling, interrupt behavior, and software registers. If any function differs, treat the change as a redesign rather than a simple component substitution and update schematic, layout, firmware, and validation tests.

Use the exact NXP package drawing and recommended land pattern for the selected orderable part. A 48-LQFP body measuring 7 mm by 7 mm does not establish lead pitch, pin numbering, or exposed-pad requirements by itself. Check assembly-process capability, stencil aperture recommendations, solder-mask clearance, and the pin-1 orientation before releasing artwork.

Operate the PCA9661B from a stable 3.3 V rail and verify the host and I2C signal thresholds against that supply. Decouple the device according to the manufacturer application guidance, including the required input and output capacitance values. During replacement planning, compare the successor's supply range and power sequencing requirements rather than assuming identical behavior.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The verified product summaries do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations for PCA9661B.

تاریخ تأیید داده‌ها: 2026-11-10 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

PCA9661B datasheet PCA9661B datasheet pdf PCA9661B pinout PCA9661B 48-LQFP PCA9661B I2C controller PCA9661B replacement PCA9661B equivalent PCA9661B vs PCA9665APW NXP PCA9661B PCA9661B price PCA9661B stock PCA9661B lead time PCA9661B application circuit PCA9661B operating voltage

قطعات و اصطلاحات مرتبط

NXP Semiconductors PCA9661B PCA9665APW I2C bus I2C controller parallel interface single-leader mode single-master mode interface IC semiconductor 3.3 V logic I2C clock frequency bus capacitance SDA SCL 48-LQFP LQFP package family surface-mount package SMD industrial control systems data acquisition communications equipment test and measurement legacy product maintenance
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ