PCA9661B - 3.3V I2C Bus Controller | NXP | LQFP-48
料号: PCA9661B ✗ 停产PCA9661B 概述
An I2C-bus controller is an interface IC that manages transactions between a parallel processor or bus master and devices connected through the two-wire I2C interface. In the broader semiconductor hierarchy, the PCA9661B belongs to the I2C controller class, which falls under interface controllers and then general-purpose interface ICs. Its role is to translate parallel data, control signaling, and bus timing into serialized I2C transfers for displays, sensors, memory devices, communications modules, and other peripheral ICs.
NXP describes the PCA9661 as an advanced, fourth-generation, single-leader-mode bus controller. The B revision is identified in the product information as a single-master or single-leader I2C controller. Its architecture is intended to support dense systems where a processor-side parallel interface must service multiple I2C destinations efficiently. Parallel-to-serial bus management can reduce repetitive software transactions by centralizing addressing, control, and status handling in dedicated hardware.
The 3.3 V operating supply matches many contemporary embedded processors, application processors, programmable logic devices, and communication controllers. This makes the PCA9661B useful in industrial controllers, test equipment, embedded computing platforms, communications infrastructure, and data-acquisition systems that already operate from a 3.3 V rail. Designers should confirm signal levels, timing limits, supported operating modes, and exact register behavior against the manufacturer datasheet before finalizing a new design.
The 48-LQFP package exposes 48 leads, but its 1.4 mm package height does not by itself determine minimum PCB pad geometry. Follow the NXP land-pattern and stencil recommendations, including exposed-pad and soldering details shown for the selected orderable variant. Account for signal propagation between the parallel interface and the I2C pins, and place pull-up and bus-capacitance components where they can maintain a short return path.
NXP marks the PCA9661B as not recommended for new designs and identifies PCA9665APW as its recommended replacement. Existing installations may continue to use the PCA9661B for maintenance or design continuity, but new products should evaluate the recommended NXP successor and confirm whether its package, pinout, registers, voltage limits, timing, and thermal characteristics permit a direct PCB substitution. The PCA9665APW is not represented here as a drop-in alternative because the available product information does not establish pin-to-pin and package equivalence.
This page organizes the verified product identity, lifecycle guidance, electrical limits, package details, design considerations, replacement analysis, and application guidance. It distinguishes confirmed manufacturer information from parameters that still require direct review of the datasheet, helping engineers separate verified device facts from assumptions before schematic capture, PCB layout, or production sourcing.
直接替换替代料: PCA9661B ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料PCA9661B 规格参数
| Device Type | I2C parallel-interface bus controller |
| Bus Interface | I2C |
| Operating Mode | Single-leader mode |
| 电源电压 | 3.3 V |
| I2C Channel Count | 1 channel |
| 工作温度范围 | -40°C to 85°C |
| 封装 | 48-LQFP |
| Package Body Size | 7 mm x 7 mm |
| Package Height | 1.40 mm |
PCA9661B 1.40 mm 引脚配置指南
PCA9661B(1.40 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: PCA9661B.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PCA9661B 适用于 6 应用s: Industrial Embedded Controllers, Data Acquisition Systems, Communications and Network Equipment, Instrumentation and Test Equipment, Display and Control Panels, Legacy Platform Maintenance.
Industrial Embedded Controllers
The PCA9661B fits industrial embedded controllers that need to connect a parallel host processor to I2C sensors, memory, display controllers, and expansion devices. Its 3.3 V supply aligns with common embedded logic levels, while the -40°C to 85°C listed operating range supports temperature-controlled equipment. The dedicated I2C controller can reduce repetitive software work by handling serialized bus transactions through hardware. However, NXP marks the PCA9661B as not recommended for new designs, so a new industrial platform should begin with the PCA9665APW and validate whether its interface, timing, and pinout meet the system requirements.
推荐
Data Acquisition Systems
Data-acquisition equipment can use the PCA9661B when multiple analog-to-digital converters, sensors, memory devices, or communication modules share an I2C bus but the system processor connects through a parallel interface. The single-channel controller provides a hardware-managed path for data-intensive I2C transfers and operates from a 3.3 V supply. Designers should calculate total bus capacitance, place pull-up resistors appropriately, and verify supported clock rate and signal timing. For newly created measurement platforms, evaluate PCA9665APW rather than committing to the legacy PCA9661B lifecycle position.
推荐
Communications and Network Equipment
The PCA9661B is applicable to communication controllers, interface modules, and embedded network equipment where a parallel processor must manage I2C peripherals such as EEPROMs, PHYs, transceivers, status monitors, or configuration devices. A hardware I2C controller can offload bus serialization from the main processor and support deterministic access to multiple addresses. The 3.3 V operating supply is consistent with many communication ICs, but level compatibility must be checked pin by pin. New networking products should use the manufacturer-recommended PCA9665APW and confirm timing, interrupt, addressing, and software-driver differences during migration.
推荐
Instrumentation and Test Equipment
Laboratory and industrial instrumentation can use the PCA9661B to bridge a parallel control processor to I2C-managed converters, EEPROMs, display drivers, calibration devices, or status registers. The 7 mm by 7 mm 48-LQFP package provides a conventional surface-mount assembly option, while the -40°C to 85°C range supports many measurement environments. Layout must preserve signal integrity on the clock and data lines and comply with the required pull-up network. Because the part is not recommended for new designs, instrument makers should prototype the PCA9665APW and perform a complete register and timing comparison before production release.
推荐
Display and Control Panels
Display-intensive control systems can employ the PCA9661B when a host processor accesses display controllers, touch controllers, indicators, configuration memories, or other I2C peripherals through a parallel interface. Consolidating serial-bus control in an interface IC can reduce host-level transaction overhead and support multiple addressed destinations. The 3.3 V device is suitable for many mixed-signal control boards, although I2C pull-up voltage selection and rise-time margin require careful review. New human-machine interfaces should favor the recommended PCA9665APW and confirm display-driver compatibility, timing margins, and software initialization sequences.
推荐
Legacy Platform Maintenance
The PCA9661B remains applicable to maintenance, repair, and lifecycle-extension programs for equipment already built around its parallel interface and 48-LQFP footprint. In this setting, preserving the approved controller can avoid board respin and software disruption when qualification, availability, and sourcing conditions are satisfactory. Engineers should document the device's not-recommended-for-new-designs status and define an obsolescence plan. A transition to PCA9665APW can be evaluated through schematic, firmware, timing, and mechanical comparisons, with the final decision based on total redesign risk rather than device identity alone.
推荐
推荐产品汇总
工程参考数据: PCA9661B ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PCA9665APW |
|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors |
| Lifecycle Recommendation | Not recommended for new designs | Manufacturer-designated replacement |
关键差异点
- Clear manufacturer lifecycle direction (对比 PCA9665APW)
- Established fourth-generation controller positioning (对比 PCA9665APW)
- Defined package and temperature identity (对比 PCA9665APW)
设计说明
Route the parallel interface and I2C clock/data nets as short, referenced paths on the PCB. Place pull-up resistors for SDA and SCL close to the bus devices with the shortest practical return connection to the supply or ground plane. Confirm the maximum supported bus rate and total bus capacitance in the manufacturer datasheet, then use scope measurements at the slowest corner to verify rise time and signal margins.
Do not treat the manufacturer-named PCA9665APW as a drop-in replacement without a pin-by-pin comparison. Check package dimensions, lead pitch, exposed-pad arrangement, supply limits, clock timing, address handling, interrupt behavior, and software registers. If any function differs, treat the change as a redesign rather than a simple component substitution and update schematic, layout, firmware, and validation tests.
Use the exact NXP package drawing and recommended land pattern for the selected orderable part. A 48-LQFP body measuring 7 mm by 7 mm does not establish lead pitch, pin numbering, or exposed-pad requirements by itself. Check assembly-process capability, stencil aperture recommendations, solder-mask clearance, and the pin-1 orientation before releasing artwork.
Operate the PCA9661B from a stable 3.3 V rail and verify the host and I2C signal thresholds against that supply. Decouple the device according to the manufacturer application guidance, including the required input and output capacitance values. During replacement planning, compare the successor's supply range and power sequencing requirements rather than assuming identical behavior.
合规信息
The verified product summaries do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations for PCA9661B.