S9S08DZ60F2CLF - 40MHz 60KB 8-Bit MCU | NXP | Automotive
MPN： S9S08DZ60F2CLF ✓ 啟用中S9S08DZ60F2CLF 概覽
What is an 8-bit microcontroller? An MCU is a semiconductor that combines a processor core, memory, and peripherals on one device. This S08 MCU belongs to the microcontroller, embedded processor, and semiconductor hierarchy. Its communication interfaces support connected control systems, while timers, PWM, and analog inputs support actuator monitoring and embedded automation.
The verified component data identifies a 60K x 8 Flash organization, 2K x 8 EEPROM, 39 I/O ports, and a maximum clock frequency of 40 MHz. The S08D family is described as supporting embedded CAN, embedded EEPROM, and on-chip emulation/debug for automotive and industrial markets. Connectivity listed for this device includes CANbus, I2C, LINbus, SCI, and SPI.
Its 48-LQFP package is a gull-wing, surface-mount package specified as 7 x 7 mm. The verified operating temperature range is -40 °C to +85 °C, and a third-party listing identifies the device as automotive qualified. These characteristics make it appropriate for temperature-range-sensitive embedded control platforms, subject to confirming the complete electrical and qualification requirements in the manufacturer documentation.
Typical uses include automotive body and motor-control electronics, industrial automation, metering equipment, IoT devices, and low-power embedded boards. The multiple serial interfaces allow the MCU to connect sensors, transceivers, actuators, and service connectors while the ADC, PWM, and watchdog support measurement, timing, and protective control functions.
A key design consideration is package and firmware compatibility: the MCU has 48 terminals, and replacement decisions must verify exact pin mapping, memory map, clock behavior, peripheral assignments, and qualification status rather than relying only on the family name. Use the NXP product page and manufacturer data sheet before finalizing a new PCB or migration.
This page consolidates verified distributor and manufacturer information, package constraints, application guidance, and replacement-screening criteria to support faster component selection while clearly separating known data from information that still requires design verification.
直接替換替代品，適用於 S9S08DZ60F2CLF — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： S9S08DZ60F2CLF （相同外形與佔位） — 差異在於 Package, Program Memory Size, Series, Number of I/O, Operating Temperature.
S9S08DZ60F2MLF
✅ 直接替換聯絡詢價
查看資料表 →MC9S08DV60ACLF
✅ 直接替換📋 參考替代品（不在目錄中）
MC9S08DV60AMLF
✅ 直接替換聯絡詢價
查看資料表 →S9S08DZ60F1CLF
✅ 直接替換📋 參考替代品（不在目錄中）
S9S08DZ96F2MLH
✅ 直接替換聯絡詢價
查看資料表 →S9S08DV60MLH
✅ 直接替換📋 參考替代品（不在目錄中）
S9S08DZ60F2CLF 最大額定值與電氣特性
| Product Type | 8-bit microcontroller |
| Series | S08D / S08 |
| Processor Core | S08, 8-bit |
| 最大時脈頻率 | 40 MHz |
| Flash Memory | 60 KB (60K x 8) |
| EEPROM | 2K x 8 bits |
| RAM | 4 KB |
| Number of I/O | 39 |
| Connectivity | CANbus, I2C, LINbus, SCI, SPI |
| ADC | Yes |
| PWM | Yes |
| Watchdog | WDT |
| Voltage Features | LVD, POR |
| 工作溫度 | -40 °C to +85 °C |
| 封裝 | 48-LQFP (7 x 7 mm) |
| Terminal Count | 48 |
| 安裝方式 | Surface mount |
| Qualification | Automotive qualified |
S9S08DZ60F2CLF 48-lqfp (7 x 7 mm) 腳位配置指南
S9S08DZ60F2CLF（48-lqfp (7 x 7 mm) 封裝）的腳位配置。 此數位 IC 包含 GPIO、通訊介面（UART、SPI、I2C）與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料： S9S08DZ60F2CLF.
請參閱 資料表 以查看完整腳位配置。
典型應用
S9S08DZ60F2CLF 適用於 6 應用s: Automotive Body Control, Industrial Automation, Embedded Motor Control, Metering and Instrumentation, IoT and Connected Embedded Devices, Low-Power Board Designs.
Automotive Body Control
The S9S08DZ60F2CLF fits automotive body-control nodes that need an 8-bit controller, 60 KB of Flash, and established vehicle-network connectivity. Its verified CANbus and LINbus support can connect switches, sensors, lamps, locks, and diagnostic equipment, while the 39 I/O and PWM outputs support mixed electromechanical functions. The -40 °C to +85 °C range and automotive-qualified listing make it suitable for early design evaluation in vehicle electronics. Before release, verify exact transceiver requirements, supply voltage, wake-up behavior, pin multiplexing, and qualification evidence against the NXP documentation.
推薦
Industrial Automation
The S9S08DZ60F2CLF is appropriate for small industrial automation controllers that coordinate sensors, actuators, and service interfaces. Its 40 MHz S08 core and 60 KB Flash provide a practical embedded platform, while SCI, SPI, and I2C connect sensors, memory, and external modules. CANbus or LINbus can provide network connectivity where the selected system architecture requires it. The ADC and PWM features support process measurement and basic actuator control, although motor-drive currents, isolation, EMC performance, and safety functions must be designed at the system level.
推薦
Embedded Motor Control
The S9S08DZ60F2CLF can serve as the supervisory controller in embedded motor-control systems where the application combines digital control, communication, and measurement. The verified 40 MHz operation supports responsive control-loop scheduling, and the PWM, ADC, watchdog, and serial interfaces provide useful building blocks for sensing, timing, and actuator management. Its automotive-qualified status is relevant for vehicle applications, but it is not a substitute for a dedicated gate-driver or motor-driver IC. Power conversion, current sensing, protection, fault handling, and thermal design require separate engineering.
推薦
Metering and Instrumentation
The S9S08DZ60F2CLF is suitable for embedded metering and instrumentation designs that require local computation, serial data exchange, and EEPROM-backed configuration. The 60 KB Flash can hold application firmware, while 4 KB RAM supports buffering and control tasks; the verified 2K x 8 EEPROM provides a potential route for calibration or configuration data, subject to its documented endurance and write requirements. ADC channels support analog measurement, and SCI, SPI, or I2C can connect displays, sensors, or service interfaces. Calibration accuracy, sensor excitation, EMC, and low-power behavior remain application-specific concerns.
推薦
IoT and Connected Embedded Devices
The S9S08DZ60F2CLF can support connected embedded nodes that combine local sensing and control with a network interface. The MCU provides I2C and SPI for sensors and local peripherals, SCI for a serial communications path, and CANbus or LINbus for embedded networking. Its 60 KB Flash and 4 KB RAM are appropriate for small firmware images and protocol stacks, while ADC and PWM support mixed input and output functions. A complete IoT product still needs a suitable transceiver, power-management circuit, antenna or network connection, security implementation, and verified low-power behavior.
推薦
Low-Power Board Designs
The S9S08DZ60F2CLF may be evaluated for low-power embedded boards that need local control, nonvolatile firmware storage, and multiple serial peripherals. The supplied product results explicitly associate the S08 family with low-power board designs, and the device combines 60 KB Flash, 4 KB RAM, EEPROM, ADC, PWM, and communication interfaces in one package. However, no sleep-current, active-current, or wake-up-time values are included in the verified data, so battery-life claims cannot be made from this record. Validate sleep modes, clock sources, peripheral shutdown behavior, and leakage using the manufacturer specifications.
推薦
推薦產品摘要
工程參考資料，適用於 S9S08DZ60F2CLF — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | S9S08DZ60F2MLF | MC9S08DV60ACLF | MC9S08DV60AMLF | S9S08DZ60F1CLF | S9S08DZ96F2MLH |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 48-LQFP (7 x 7 mm) | 48-LQFP (7 x 7 mm) - related package | 48-LQFP (7 x 7 mm) - related package | 48-LQFP (7 x 7 mm) - related package | 48-LQFP (7 x 7 mm) - related package | 48-LQFP (7 x 7 mm) - related package |
主要差異化特點
- Verified automotive-oriented feature set (對比MC9S08DV60ACLF)
- Documented connectivity breadth (對比S9S08DZ60F1CLF)
- Integrated memory configuration (對比S9S08DZ96F2MLH)
- Industrial and automotive control positioning (對比MC9S08DV60AMLF)
設計說明
Treat the 48-LQFP footprint as a controlled interface rather than a generic 48-pin package. Before layout approval, compare the official pinout, power and ground assignments, exposed thermal requirements, and peripheral multiplexing for the exact S9S08DZ60F2CLF orderable part. The supplied data confirms a 7 x 7 mm gull-wing package but does not provide the numbered pin list, so a footprint-only substitution is not sufficient.
Plan the MCU supply and decoupling around the complete NXP electrical specification, not only the 40 MHz headline frequency. The verified data confirms LVD and POR features but does not provide operating-voltage limits, current consumption, or power-mode currents. Confirm supply tolerances, decoupling values, startup sequencing, and the current required by attached CANbus, LINbus, ADC, and PWM loads before finalizing the power tree.
Separate communication and analog routing where practical. Keep clock, reset, and sensitive sensor paths short; route high-current actuator outputs away from the MCU and ADC region; and place protection close to connectors exposed to external wiring. Because the supplied data does not identify every pin or package thermal detail, use the manufacturer land pattern and recommended layout guidance during PCB implementation.
Do not select a replacement from the S08 family name alone. Verify the exact orderable MPN, 48-LQFP dimensions, pin assignments, clock limits, Flash and RAM organization, EEPROM availability, peripheral set, automotive qualification, and firmware compatibility. A related MPN may share a family and package description while differing in pinout or device behavior, which can cause a board failure despite apparent similarity.
合規資訊
The verified results identify the device as automotive qualified but do not provide RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is therefore recorded as not_applicable rather than inferred.