S9S08DZ60F2CLF - 40MHz 60KB 8-Bit MCU | NXP | Automotive
MPN: S9S08DZ60F2CLF ✓ Hoạt độngS9S08DZ60F2CLF Tóm tắt
What is an 8-bit microcontroller? An MCU is a semiconductor that combines a processor core, memory, and peripherals on one device. This S08 MCU belongs to the microcontroller, embedded processor, and semiconductor hierarchy. Its communication interfaces support connected control systems, while timers, PWM, and analog inputs support actuator monitoring and embedded automation.
The verified component data identifies a 60K x 8 Flash organization, 2K x 8 EEPROM, 39 I/O ports, and a maximum clock frequency of 40 MHz. The S08D family is described as supporting embedded CAN, embedded EEPROM, and on-chip emulation/debug for automotive and industrial markets. Connectivity listed for this device includes CANbus, I2C, LINbus, SCI, and SPI.
Its 48-LQFP package is a gull-wing, surface-mount package specified as 7 x 7 mm. The verified operating temperature range is -40 °C to +85 °C, and a third-party listing identifies the device as automotive qualified. These characteristics make it appropriate for temperature-range-sensitive embedded control platforms, subject to confirming the complete electrical and qualification requirements in the manufacturer documentation.
Typical uses include automotive body and motor-control electronics, industrial automation, metering equipment, IoT devices, and low-power embedded boards. The multiple serial interfaces allow the MCU to connect sensors, transceivers, actuators, and service connectors while the ADC, PWM, and watchdog support measurement, timing, and protective control functions.
A key design consideration is package and firmware compatibility: the MCU has 48 terminals, and replacement decisions must verify exact pin mapping, memory map, clock behavior, peripheral assignments, and qualification status rather than relying only on the family name. Use the NXP product page and manufacturer data sheet before finalizing a new PCB or migration.
This page consolidates verified distributor and manufacturer information, package constraints, application guidance, and replacement-screening criteria to support faster component selection while clearly separating known data from information that still requires design verification.
Bộ thay thế dễ dàng lắp đặt cho S9S08DZ60F2CLF — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với S9S08DZ60F2CLF (cùng hình factor và footprint) — khác nhau ở Package, Program Memory Size, Series, Number of I/O, Operating Temperature.
S9S08DZ60F2MLF
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC9S08DV60ACLF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC9S08DV60AMLF
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →S9S08DZ60F1CLF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
S9S08DZ96F2MLH
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →S9S08DV60MLH
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
S9S08DZ60F2CLF Tỷ lệ tối đa & tính chất điện
| Product Type | 8-bit microcontroller |
| Series | S08D / S08 |
| Processor Core | S08, 8-bit |
| Tần số xung maksimum | 40 MHz |
| Flash Memory | 60 KB (60K x 8) |
| EEPROM | 2K x 8 bits |
| RAM | 4 KB |
| Number of I/O | 39 |
| Connectivity | CANbus, I2C, LINbus, SCI, SPI |
| ADC | Yes |
| PWM | Yes |
| Watchdog | WDT |
| Voltage Features | LVD, POR |
| Nhiệt độ hoạt động | -40 °C to +85 °C |
| Hộp | 48-LQFP (7 x 7 mm) |
| Terminal Count | 48 |
| Kiểu lắp đặt | Surface mount |
| Qualification | Automotive qualified |
Hướng dẫn cấu hình chân S9S08DZ60F2CLF 48-lqfp (7 x 7 mm)
Cấu hình chân cho S9S08DZ60F2CLF (48-lqfp (7 x 7 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho S9S08DZ60F2CLF.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
S9S08DZ60F2CLF phù hợp cho 6 Áp dụngs: Automotive Body Control, Industrial Automation, Embedded Motor Control, Metering and Instrumentation, IoT and Connected Embedded Devices, Low-Power Board Designs.
Automotive Body Control
The S9S08DZ60F2CLF fits automotive body-control nodes that need an 8-bit controller, 60 KB of Flash, and established vehicle-network connectivity. Its verified CANbus and LINbus support can connect switches, sensors, lamps, locks, and diagnostic equipment, while the 39 I/O and PWM outputs support mixed electromechanical functions. The -40 °C to +85 °C range and automotive-qualified listing make it suitable for early design evaluation in vehicle electronics. Before release, verify exact transceiver requirements, supply voltage, wake-up behavior, pin multiplexing, and qualification evidence against the NXP documentation.
Được đề xuất
Industrial Automation
The S9S08DZ60F2CLF is appropriate for small industrial automation controllers that coordinate sensors, actuators, and service interfaces. Its 40 MHz S08 core and 60 KB Flash provide a practical embedded platform, while SCI, SPI, and I2C connect sensors, memory, and external modules. CANbus or LINbus can provide network connectivity where the selected system architecture requires it. The ADC and PWM features support process measurement and basic actuator control, although motor-drive currents, isolation, EMC performance, and safety functions must be designed at the system level.
Được đề xuất
Embedded Motor Control
The S9S08DZ60F2CLF can serve as the supervisory controller in embedded motor-control systems where the application combines digital control, communication, and measurement. The verified 40 MHz operation supports responsive control-loop scheduling, and the PWM, ADC, watchdog, and serial interfaces provide useful building blocks for sensing, timing, and actuator management. Its automotive-qualified status is relevant for vehicle applications, but it is not a substitute for a dedicated gate-driver or motor-driver IC. Power conversion, current sensing, protection, fault handling, and thermal design require separate engineering.
Được đề xuất
Metering and Instrumentation
The S9S08DZ60F2CLF is suitable for embedded metering and instrumentation designs that require local computation, serial data exchange, and EEPROM-backed configuration. The 60 KB Flash can hold application firmware, while 4 KB RAM supports buffering and control tasks; the verified 2K x 8 EEPROM provides a potential route for calibration or configuration data, subject to its documented endurance and write requirements. ADC channels support analog measurement, and SCI, SPI, or I2C can connect displays, sensors, or service interfaces. Calibration accuracy, sensor excitation, EMC, and low-power behavior remain application-specific concerns.
Được đề xuất
IoT and Connected Embedded Devices
The S9S08DZ60F2CLF can support connected embedded nodes that combine local sensing and control with a network interface. The MCU provides I2C and SPI for sensors and local peripherals, SCI for a serial communications path, and CANbus or LINbus for embedded networking. Its 60 KB Flash and 4 KB RAM are appropriate for small firmware images and protocol stacks, while ADC and PWM support mixed input and output functions. A complete IoT product still needs a suitable transceiver, power-management circuit, antenna or network connection, security implementation, and verified low-power behavior.
Được đề xuất
Low-Power Board Designs
The S9S08DZ60F2CLF may be evaluated for low-power embedded boards that need local control, nonvolatile firmware storage, and multiple serial peripherals. The supplied product results explicitly associate the S08 family with low-power board designs, and the device combines 60 KB Flash, 4 KB RAM, EEPROM, ADC, PWM, and communication interfaces in one package. However, no sleep-current, active-current, or wake-up-time values are included in the verified data, so battery-life claims cannot be made from this record. Validate sleep modes, clock sources, peripheral shutdown behavior, and leakage using the manufacturer specifications.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho S9S08DZ60F2CLF — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | S9S08DZ60F2MLF | MC9S08DV60ACLF | MC9S08DV60AMLF | S9S08DZ60F1CLF | S9S08DZ96F2MLH |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 48-LQFP (7 x 7 mm) | 48-LQFP (7 x 7 mm) - related package | 48-LQFP (7 x 7 mm) - related package | 48-LQFP (7 x 7 mm) - related package | 48-LQFP (7 x 7 mm) - related package | 48-LQFP (7 x 7 mm) - related package |
Bảo phân biệt quan trọng
- Verified automotive-oriented feature set (vsMC9S08DV60ACLF)
- Documented connectivity breadth (vsS9S08DZ60F1CLF)
- Integrated memory configuration (vsS9S08DZ96F2MLH)
- Industrial and automotive control positioning (vsMC9S08DV60AMLF)
Ghi chú thiết kế
Treat the 48-LQFP footprint as a controlled interface rather than a generic 48-pin package. Before layout approval, compare the official pinout, power and ground assignments, exposed thermal requirements, and peripheral multiplexing for the exact S9S08DZ60F2CLF orderable part. The supplied data confirms a 7 x 7 mm gull-wing package but does not provide the numbered pin list, so a footprint-only substitution is not sufficient.
Plan the MCU supply and decoupling around the complete NXP electrical specification, not only the 40 MHz headline frequency. The verified data confirms LVD and POR features but does not provide operating-voltage limits, current consumption, or power-mode currents. Confirm supply tolerances, decoupling values, startup sequencing, and the current required by attached CANbus, LINbus, ADC, and PWM loads before finalizing the power tree.
Separate communication and analog routing where practical. Keep clock, reset, and sensitive sensor paths short; route high-current actuator outputs away from the MCU and ADC region; and place protection close to connectors exposed to external wiring. Because the supplied data does not identify every pin or package thermal detail, use the manufacturer land pattern and recommended layout guidance during PCB implementation.
Do not select a replacement from the S08 family name alone. Verify the exact orderable MPN, 48-LQFP dimensions, pin assignments, clock limits, Flash and RAM organization, EEPROM availability, peripheral set, automotive qualification, and firmware compatibility. A related MPN may share a family and package description while differing in pinout or device behavior, which can cause a board failure despite apparent similarity.
Thông tin tuân thủ
The verified results identify the device as automotive qualified but do not provide RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is therefore recorded as not_applicable rather than inferred.