SN74HC623N - 8-Bit 3-State Bus Transceiver | Texas Instruments
MPN: SN74HC623N ✓ 啟用中SN74HC623N 概覽
A bus transceiver is a bidirectional interface IC that connects a digital system to shared parallel buses. The bus transceiver category belongs to the broader digital logic hierarchy, which includes buffers, drivers, receivers, transceivers, and interface ICs. Unlike a unidirectional buffer or driver, a transceiver can receive data from a bus and drive the same bus when enabled. The 3-state output condition provides a high-impedance state that electrically isolates a device from the shared conductor whenever it is not selected.
The SN74HC623 is designed around the SN74HC logic family. Its key documented characteristics include eight non-inverting transceiver channels, three-state outputs, one 8-bit element, and a 20-pin DIP package. These attributes make it suitable for systems that need controlled bidirectional access to a parallel bus. Exact propagation-delay, current, voltage, and temperature limits should be taken from the corresponding Texas Instruments datasheet tables during design sign-off.
The three-state output control is especially useful in bus arbitration, memory interfacing, peripheral sharing, and modular computer architectures. When a connected device is not participating in a transfer, its outputs can be disabled to avoid bus contention. When enabled, the transceiver provides a defined logic path between the bus and the host-side logic. Designers should still check the data sheet for direction-control timing, output-drive capability, and input thresholds required by the particular system.
SN74HC623N is appropriate for conventional TTL and CMOS-compatible systems that specifically require a DIP-compatible octal bus interface. The N suffix identifies the listed 20-pin plastic DIP configuration, which is useful for legacy motherboard designs, controller boards, prototypes, and maintenance systems that cannot accept a surface-mount package. The through-hole format also simplifies socketed prototyping and field replacement where an appropriate qualified socket and insertion system are used.
PCB implementation should preserve the standard 20-pin DIP pin numbering and provide adequate clearance around the package. Supply rails should be decoupled close to the device using the capacitance values specified by the manufacturer, and every unused input must be connected to a defined logic level. Because a transceiver can actively drive a bus, system designers should verify enable timing and ensure that no two enabled outputs conflict during mode transitions.
This page combines the manufacturer product identity, package information, sourcing details, drop-in alternatives, and practical implementation guidance for engineers evaluating the SN74HC623N. For an exact replacement decision, confirm the full ordering suffix, operating-voltage range, temperature grade, logic thresholds, timing limits, and pin function against the original system requirements before releasing a production BOM.
直接替換替代品,適用於 SN74HC623N — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
SN74HCT623N
✅ 直接替換📋 參考替代品(不在目錄中)
SN74HC623N 最大額定值與電氣特性
| Device Type | Octal bus transceiver |
| Logic Family | SN74HC |
| Number of Bits | 8 bits |
| Element Count | 1 element |
| Bits per Element | 8 bits |
| Direction | Bidirectional |
| Logic Polarity | Non-inverting |
| Output State | 3-state |
| 封裝 | 20-pin plastic DIP (PDIP) |
| Package Body Width | 0.300 in (7.62 mm) |
| 安裝類型 | Through-hole |
| Packaging Form | Tube |
| AEC-Q100 Qualification | not_applicable |
SN74HC623N 0.300 in (7.62 mm) 腳位配置指南
SN74HC623N(0.300 in (7.62 mm) 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: SN74HC623N.
請參閱 資料表 以查看完整腳位配置。
典型應用
SN74HC623N 適用於 6 應用s: Shared Parallel Computer Bus, Memory-Module Bus Interface, Peripheral Sharing and Arbitration, Industrial Control Backplane, Legacy CPU Data-Bus Isolation, Test and Measurement Data Interface.
Shared Parallel Computer Bus
The SN74HC623N can connect one controller or peripheral card to a shared eight-bit parallel bus when both sides require controlled bidirectional participation. Its eight non-inverting channels and three-state outputs allow unused devices to isolate themselves from the bus, while an active device can receive data or place a valid logic level on the line. The 20-pin PDIP format is useful in legacy expansion systems, controller boards, and prototypes that require a socketable through-hole component. Before finalizing the interface, verify enable timing, input thresholds, output-drive strength, bus capacitance, and the maximum supported clock rate against the Texas Instruments datasheet.
推薦
Memory-Module Bus Interface
The SN74HC623N is suitable for a legacy memory or peripheral bus where several devices may need access to the same eight data conductors. Its three-state outputs are the key implementation benefit: a device that is not selected can remain electrically disconnected, preventing unwanted drive contention while another participant transfers data. The eight non-inverting channels support byte-wide parallel signaling. A sound design must define every control state during power-up and reset, check setup and hold timing against the bus clock, and confirm that the connected memory technology has compatible voltage levels and output impedance.
推薦
Peripheral Sharing and Arbitration
The SN74HC623N can be used in peripheral-sharing arrangements where two or more bus agents must not drive the same line simultaneously. Three-state outputs allow an inactive agent to release the bus, while proper arbitration logic enables only the intended participant. The device's non-inverting operation simplifies integration with ordinary active-high logic, and the 20-pin PDIP package supports repairable and socketed industrial controller hardware. Engineers should establish deterministic enable priorities, provide pull resistors where required by the interface specification, and validate break-before-make behavior during every arbitration transition.
推薦
Industrial Control Backplane
The SN74HC623N can interface a control card with an industrial backplane carrying byte-wide data and shared control signals. Its through-hole package is particularly practical for legacy PLC and industrial controller revisions that use socketed logic and demand straightforward field replacement. The three-state outputs help isolate inactive modules from a common bus, reducing the chance of data contention. The circuit should use a defined termination and biasing strategy, maintain compatible logic thresholds across every attached module, and include protection appropriate to the installation environment rather than assuming that the logic device alone handles connector transients.
推薦
Legacy CPU Data-Bus Isolation
The SN74HC623N can place a selected byte of logic between a legacy processor bus and a local subsystem while the three-state outputs isolate the local device from the bus when it is not selected. This arrangement is useful in controller revisions where address decoding and bus contention are managed by external logic. The 20-pin PDIP package makes it practical to update existing through-hole boards without changing their mechanical footprint. Designers should inspect the datasheet's direction-control truth table, account for bus rise and fall times, and ensure that every transition prevents overlap between an outgoing bus driver and the local subsystem's output driver.
推薦
Test and Measurement Data Interface
The SN74HC623N can be used as a selectable byte-wide interface between a test fixture, instrument, and external digital bus. Its three-state behavior allows several instrument functions to share conductors without requiring every node to remain permanently active. The non-inverting channel arrangement supports straightforward connection to common control logic, and the PDIP package is convenient for laboratory adapters and hand-built test hardware. For dependable measurements, the bus must have controlled thresholds, defined idle states, suitable clock and settling margins, and no unintended capacitive loading from long fixture wiring.
推薦
推薦產品摘要
工程參考資料,適用於 SN74HC623N — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | SN74HCT623N |
|---|---|---|
| Package | 20-pin PDIP | 20-pin PDIP |
| Brand | Texas Instruments | Texas Instruments |
| Device Type | Octal bus transceiver | Octal bus transceiver |
| Logic Family | SN74HC | SN74HCT |
| Number of Bits | 8 bits | 8 bits |
| Element Count | 1 element | 1 element |
| Logic Polarity | Non-inverting | Non-inverting |
| Output State | 3-state | 3-state |
| Input Threshold Family | HC CMOS thresholds | TTL-compatible thresholds |
主要差異化特點
- HC CMOS input-threshold behavior (對比SN74HCT623N)
- Exact through-hole footprint (對比SN74HCT623N)
- Matching octal three-state bus interface (對比SN74HCT623N)
設計說明
Treat output-enable and direction transitions as a bus-safety problem, not merely a timing detail. Ensure the control logic produces break-before-make behavior so that the outgoing driver releases a line before the next device begins driving it. Use the SN54HC623 and SN74HC623 datasheet truth table to confirm every mode, and bring all enable inputs to defined states during power-up and reset so that no two devices contend on the bus.
Use the standard 20-pin PDIP footprint, preserve pin-1 orientation, and avoid placing tall components where they interfere with socket removal. Place the manufacturer-recommended bypass capacitor close to the supply and ground pins with a short current path. Keep the eight bus traces reasonably short, provide a continuous ground reference, and route control traces away from high-current switching nodes to reduce opportunities for false bus transitions.
Validate the complete bus topology rather than relying on the nominal logic speed. Account for conductor length, connector capacitance, stub effects, pull-up or pull-down strength, and the selected transceiver's output-drive capability. Confirm that rise and fall times meet the receiving device's limits and that the clock rate satisfies the worst-case propagation-delay and setup-time combination. Scheduled testing with an oscilloscope can reveal ringing and enable overlap that static logic analysis may miss.
Confirm the SN74HC623N supply limits and input-threshold behavior against the voltages produced by every connected device. The HC and HCT logic families must not be treated as interchangeable merely because their packages match. Check high-level and low-level noise margin at the actual supply voltage, and ensure that the supply remains within its rated range during startup, reset, and loaded bus transitions.
合規資訊
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was identified in the product listings. AEC-Q100 is not applicable to this general-purpose commercial logic device.