SN74HC645N - Octal 3-State Bus Transceiver | Texas Instruments
MPN: SN74HC645N ✓ 啟用中SN74HC645N 概覽
A bus transceiver is a bidirectional interface device that connects two logic buses while controlling signal direction and bus contention. The SN74HC645N belongs to the hierarchy of CMOS logic integrated circuits, specifically bus transceivers and bus interface logic. Unlike a unidirectional buffer, it can carry data in either direction without a DIR control pin, making it suitable for bidirectional data buses, memory interfaces, and processor data ports.
Key features include eight non-inverting bus channels, 3-state output control, and a single active-low output-enable input. The non-inverting signal path preserves input polarity, so the same logic level appears on the opposite side of the device. The 3-state outputs allow multiple devices to share a bus when their output-enable signals are controlled correctly, while the disabled state provides high impedance to minimize loading and prevent bus contention.
The SN74HC645N uses 74HC-series high-speed CMOS logic. Its operating supply range covers the conventional 5 V CMOS environment as well as lower-voltage systems operating at 3.3 V or 2.5 V. The device belongs to the broader category of low-power digital logic integrated circuits, alongside buffers, drivers, transceivers, and interface controllers. Its PDIP-20 package provides through-hole lead spacing for conventional through-hole PCB assembly rather than a surface-mount land pattern.
Typical uses include bidirectional data buses in embedded control systems, interface isolation between circuit sections, memory-module connections, test-equipment signal routing, and communications equipment. Because the transceiver automatically selects the active data direction, firmware does not need to manage a direction-control signal. Designers must still ensure that only one device drives a shared bus at a time and that output-enable timing meets the requirements of every attached device.
The primary design consideration is bus contention. Asserting output enable while another device drives the same bus can produce excessive current and undefined logic levels. The output-enable pin should be driven by a controller with defined startup and shutdown states, and unused inputs should be held at a valid CMOS level. Decoupling close to the supply pins, adequate ground-return routing, and controlled enable sequencing are essential for reliable operation.
This page combines the manufacturer device information, pin assignment, practical bus-interface design guidance, and drop-in replacement analysis to support faster component selection and PCB-level decision making.
直接替換替代品,適用於 SN74HC645N — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
74HC645N
✅ 直接替換📋 參考替代品(不在目錄中)
MC74HC645N
✅ 直接替換📋 參考替代品(不在目錄中)
TC74HC645N
✅ 直接替換📋 參考替代品(不在目錄中)
HD74HC645P
✅ 直接替換📋 參考替代品(不在目錄中)
MC74HC645AN
✅ 直接替換📋 參考替代品(不在目錄中)
SN74HC645N 最大額定值與電氣特性
| Device Type | Octal bus transceiver |
| Number of Elements | 1 element |
| Bits per Element | 8 bits |
| Direction | Bidirectional, automatic |
| Logic Type | Non-inverting |
| Output State | 3-state, high-impedance disabled |
| Number of Bus Lines | 8 lines |
| Supply Voltage Range | 2 V to 6 V |
| 工作溫度範圍 | -40 °C to +85 °C |
| 封裝 | PDIP-20 |
| 腳位數 | 20 pins |
| 安裝類型 | Through-hole, PDIP |
| Output Enable | Active-low, shared by all eight channels |
SN74HC645N 腳位配置
| 腳位 1 | 1A — Bus terminal for channel 1, A side |
| 腳位 2 | 1B — Bus terminal for channel 1, B side |
| 腳位 3 | 2A — Bus terminal for channel 2, A side |
| 腳位 4 | 2B — Bus terminal for channel 2, B side |
| 腳位 5 | 3A — Bus terminal for channel 3, A side |
| 腳位 6 | 3B — Bus terminal for channel 3, B side |
| 腳位 7 | 4A — Bus terminal for channel 4, A side |
| 腳位 8 | 4B — Bus terminal for channel 4, B side |
| 腳位 9 | 5A — Bus terminal for channel 5, A side |
| 腳位 10 | 5B — Bus terminal for channel 5, B side |
| 腳位 11 | 6A — Bus terminal for channel 6, A side |
| 腳位 12 | 6B — Bus terminal for channel 6, B side |
| 腳位 13 | 7A — Bus terminal for channel 7, A side |
| 腳位 14 | 7B — Bus terminal for channel 7, B side |
| 腳位 15 | 8A — Bus terminal for channel 8, A side |
| 腳位 16 | 8B — Bus terminal for channel 8, B side |
| 腳位 17 | GND — Ground reference terminal |
| 腳位 18 | OE — Active-low output enable; high impedance when high |
| 腳位 19 | VCC — Positive power-supply terminal |
| 腳位 20 | GND — Ground reference terminal |
典型應用
SN74HC645N 適用於 6 應用s: Embedded Processor Bidirectional Data Bus, Memory and Peripheral Bus Isolation, Test and Measurement Signal Routing, Communication Equipment Backplane Interface, Shared Peripheral Data Port, Legacy 5 V Digital System Retrofit.
Embedded Processor Bidirectional Data Bus
The SN74HC645N is appropriate when a processor port must exchange data with peripherals over a shared 8-bit bus. Its eight automatic-direction channels remove the need for a firmware-controlled DIR signal, while the common active-low output-enable input allows the controller to isolate the transceiver during reset or another device's transfer. The 2 V to 6 V operating range supports 5 V, 3.3 V, and 2.5 V logic systems, although system-level timing must remain within the device's propagation-delay limits documented by Texas Instruments.
推薦
Memory and Peripheral Bus Isolation
Placed between a memory bus and a logic section, the SN74HC645N provides high-impedance isolation without breaking bidirectional transfers. Its 3-state outputs allow the port to disconnect while another bus master is active, reducing the risk of contention if the enable controller follows a defined sequence. The non-inverting signal path preserves data polarity, and the 20-pin PDIP footprint is convenient for through-hole industrial control equipment and prototype assemblies.
推薦
Test and Measurement Signal Routing
The SN74HC645N can route a group of eight test signals between an instrument controller and a device under test while placing the bus in a high-impedance state during measurement intervals. Automatic direction detection handles controller-to-DUT and DUT-to-controller transfers on the same conductors. The 2 V to 6 V supply range permits use with legacy 5 V instrumentation as well as modern 3.3 V control hardware, but input thresholds and timing should be checked for every connected instrument.
推薦
Communication Equipment Backplane Interface
In communication equipment, the SN74HC645N can connect an internal processor or controller to a card-edge or backplane bus when the interface requires eight bidirectional, non-inverting channels. The common output-enable function simplifies card isolation during bus arbitration, while automatic direction handling reduces logic overhead. Its -40 °C to +85 °C operating range covers industrial environments, and the PDIP-20 package supports serviceable and through-hole industrial hardware designs.
推薦
Shared Peripheral Data Port
The SN74HC645N is useful when two board-level controllers or peripherals must exchange data over the same eight conductors. Its tri-state outputs permit controlled disconnection of an unused port, and the automatic direction behavior supports symmetric communication between the two devices. Because output-enable state defines whether the outputs are active or high impedance, the system controller should enforce exclusive bus ownership during startup, reset, and mode transitions.
推薦
Legacy 5 V Digital System Retrofit
The SN74HC645N can serve as a standardized 8-bit interface in older 5 V CMOS systems that require bidirectional tri-state bus capability. Its 2 V to 6 V operating range includes the nominal 5 V rail, and its through-hole PDIP-20 package is easy to install on older control boards. A retrofit should verify the original bus timing, enable polarity, and contention behavior, since faster or slower third-party transceivers can alter margin at the system level.
推薦
工程參考資料,適用於 SN74HC645N — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | 74HC645N | MC74HC645N | TC74HC645N | HD74HC645P | MC74HC645AN |
|---|---|---|---|---|---|---|
| Package | PDIP-20 | PDIP-20 | PDIP-20 | PDIP-20 | PDIP-20 | PDIP-20 |
| Brand | Texas Instruments | Nexperia | onsemi | Toshiba | Hitachi | onsemi |
| Function | Octal non-inverting bus transceiver | Octal non-inverting bus transceiver | Octal non-inverting bus transceiver | Octal non-inverting bus transceiver | Octal non-inverting bus transceiver | Octal non-inverting bus transceiver |
| Direction Control | Automatic direction | Automatic direction | Automatic direction | Automatic direction | Automatic direction | Automatic direction |
| Output State | 3-state | 3-state | 3-state | 3-state | 3-state | 3-state |
| Number of Bus Lines | 8 lines | 8 lines | 8 lines | 8 lines | 8 lines | 8 lines |
| Mounting Type | Through-hole PDIP | Through-hole PDIP | Through-hole PDIP | Through-hole PDIP | Through-hole PDIP | Through-hole PDIP |
主要差異化特點
- Automatic bidirectional operation eliminates an external DIR pin (對比SN74HC245N)
- Established Texas Instruments 74HC-family documentation and sourcing (對比74HC645N)
- Same 20-pin PDIP interface as the listed 74HC645 substitutes (對比MC74HC645N)
設計說明
Do not allow two enabled transceivers to drive the same bus simultaneously. The SN74HC645N automatically selects data direction, but it cannot prevent contention when two devices independently decide that they own the bus. Define a single bus-arbitration or enable-control function, hold the output-enable terminal in its inactive high-impedance state during reset, and ensure startup states cannot force two drivers active at the same time.
Route the eight paired bus conductors as compact, consistently referenced nets and connect the two ground terminals to an uninterrupted ground plane or equivalent return path. Place the device close to the bus interface when propagation-delay margin is limited, and avoid long stubs from the transceiver to connectors or test points. Because the PDIP-20 package has no dedicated exposed pad, thermal performance and mechanical support depend on the through-hole footprint rather than a bottom thermal pad.
Treat every A and B terminal as a bidirectional node capable of changing direction without a DIR command. Check both pull-up and pull-down behavior at the bus receiver, account for the off-state leakage of every connected device, and use ringing or overshoot measurements to validate longer cables or backplanes. A tri-state output removes drive current but does not remove the need to control the logic level of an undriven shared bus.
合規資訊
The manufacturer product and datasheet links were identified, but no explicit compliance declarations were captured for this specific orderable MPN.