SN74LS685N - 8-Bit Magnitude Comparator | Texas Instruments
MPN: SN74LS685N ✓ 啟用中SN74LS685N 概覽
A magnitude comparator is a digital logic IC that compares two multi-bit unsigned values and produces relational outputs. The SN74LS685N performs this function across two complete 8-bit input groups, reducing the need for several single-bit comparator or gate networks. Magnitude comparators sit within the broader logic-IC hierarchy, alongside arithmetic, interface, memory, and control devices. Their outputs can indicate equality as well as the direction of the numerical relationship, making them useful between data-processing blocks and system decision logic.
The defining features are an 8-bit comparison width, inverted comparison outputs, LS-series TTL implementation, and PDIP-20 mechanical package. The inverted outputs are important during logic design because active-low assertions must be treated consistently with the rest of the circuit. The NS suffix identifies the standard Texas Instruments package and commercial-temperature ordering configuration. Because the device uses a through-hole PDIP package, it can also suit educational, industrial-control, test-equipment, and legacy-computing assemblies where through-hole assembly and socketed serviceability remain practical.
The SN74LS685N provides a straightforward hardware comparison stage. Two 8-bit buses enter the comparator, while dedicated outputs report the relationship between them. This allows a system to make a decision without first subtracting the operands or comparing them sequentially in a processor. The architecture is particularly useful when a decision must be generated quickly and consistently, or when control logic must respond to equal, greater-than, and less-than conditions independently.
Typical applications include digital address decoding, equality checking in control systems, threshold decision logic, numeric sorting networks, event counters, legacy processor interfaces, and industrial automation equipment. In an address decoder, for example, the comparator can test whether a bus matches a programmed or dynamically generated value and enable the associated circuit only when equality is asserted. In test equipment, its three relational outputs can simplify fixture routing and pass-fail detection.
PCB design should preserve the logic polarity of the inverted outputs and route each 8-bit input group as a coherent bus to reduce mismatch between corresponding bits. Maintain adequate bypass capacitance at the power pins and avoid relying on the comparator outputs to source loads beyond the device's specified output-current and fan-out limits. When replacing an existing part, verify the complete pinout, supply requirements, temperature range, output timing, and propagation-delay characteristics rather than relying on the comparator function alone.
This product page combines the device identity, package details, functional hierarchy, comparison design guidance, practical applications, and drop-in replacement analysis into an engineering-focused reference for the Texas Instruments SN74LS685N 8-bit magnitude comparator.
直接替換替代品,適用於 SN74LS685N — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
SN74LS685FN
✅ 直接替換📋 參考替代品(不在目錄中)
DM74LS685N
✅ 直接替換📋 參考替代品(不在目錄中)
SN74LS685N 最大額定值與電氣特性
| Comparator Type | 8-bit magnitude and identity comparator |
| Logic Family | LS-series TTL |
| Input Data Width | 8 bits per compared operand |
| Number of Compared Operands | 2 operands |
| Output Polarity | Inverted logic output |
| Package Type | PDIP-20 |
| 腳位數 | 20 pins |
| 安裝方式 | Through-hole |
SN74LS685N pdip-20 腳位配置指南
SN74LS685N(pdip-20 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: SN74LS685N.
請參閱 資料表 以查看完整腳位配置。
典型應用
SN74LS685N 適用於 6 應用s: Digital Address Decoding, Equality Detection in Control Systems, Pass-Fail Test Equipment, Numeric Sorting and Threshold Logic, Legacy Processor Interface Logic, Educational and Retro Logic Systems.
Digital Address Decoding
The SN74LS685N is suitable for decoding an 8-bit address or data word because it compares two complete 8-bit operands and provides separate greater-than, less-than, and equality indications. Place the candidate address on one input group and the destination word on the other, then use the inverted equality output to qualify the associated enable or chip-select function. This hardware decision can replace a software comparison in legacy processor and peripheral-control designs. The principal design consideration is output polarity: the active-low relationship must be treated consistently with the surrounding TTL logic.
推薦
Equality Detection in Control Systems
The SN74LS685N can detect whether two 8-bit machine states are identical without cascading individual bit comparators. A controller can present its current command word and a stored reference word, then use the inverted equality indication to trigger a state transition, alarm inhibit, or actuator enable. Using one dedicated comparator simplifies the logic and reduces the number of packages required for the comparison function. For reliable operation, keep corresponding bits in the same logic family and interpret the inverted outputs according to the manufacturer truth table.
推薦
Pass-Fail Test Equipment
The SN74LS685N provides a convenient 8-bit equality and magnitude test stage for legacy test fixtures, interface boards, and diagnostic equipment. Apply the measured or source word to one input group and the expected limit to the other; the three relational outputs then identify whether the value is below, equal to, or above the programmed reference. These indications can drive pass indicators, sorting commands, or fixture routing. Validate propagation delay and output loading at the intended clock rate before using the comparator in high-speed automated test paths.
推薦
Numeric Sorting and Threshold Logic
The SN74LS685N can form the decision element in an 8-bit sorting, ranking, or threshold system. By comparing the current value with another stored value, it provides independent less-than, equality, and greater-than indications for the next sorting stage or control action. This is particularly useful in mechanical control, batch processing, and older industrial systems where comparator ICs are preferred over programmable logic. Designers should account for the comparison propagation delay when sequencing cascaded stages, and should use consistent bus timing to prevent metastability-like sampling errors at system boundaries.
推薦
Legacy Processor Interface Logic
The SN74LS685N can assist older microprocessor systems with bus-value recognition, memory-region testing, and conditional interrupt generation. Its two 8-bit input groups accommodate a complete data or address word, while the relational outputs allow the system to react immediately to a recognized condition. This reduces the software and discrete gate burden associated with wide equality detection. When interfacing a legacy processor, check output timing against the processor bus requirements, preserve the comparator's inverted output convention, and avoid excessive loading on the buses connected to the device.
推薦
Educational and Retro Logic Systems
The SN74LS685N is practical for educational breadboards, retro-computing experiments, and repairable through-hole logic projects. Students can connect two 8-bit values with switches or bus drivers and observe the three inverted comparison outputs, making the relationship between numerical magnitude and logic indication easy to visualize. The PDIP-20 format supports sockets, rework, and replacement in older assemblies. Because classic LS-series devices are not intended for modern high-speed logic, operate the comparator within its specified supply and timing limits and use clean, stable input conditions.
推薦
推薦產品摘要
工程參考資料,適用於 SN74LS685N — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | SN74LS685FN | DM74LS685N |
|---|---|---|---|
| Package | PDIP-20 | PDIP-20 | PDIP-20 |
| Brand | Texas Instruments | Motorola, Inc | Motorola, Inc |
| Comparison Width | 8 bits | 8 bits | 8 bits |
| Comparator Function | Magnitude and identity comparator | Magnitude and identity comparator | Magnitude and identity comparator |
| Output Polarity | Inverted | Inverted | Inverted |
| Logic Family | LS-series TTL | 74LS-series TTL | 74LS-series TTL |
| Mounting Style | Through-hole | Through-hole | Through-hole |
| Number of Pins | 20 pins | 20 pins | 20 pins |
主要差異化特點
- Dedicated 8-bit relational comparison (對比SN74LS685FN)
- Matching active-low output convention (對比DM74LS685N)
- Serviceable 20-pin through-hole implementation (對比SN74LS685DW)
設計說明
Route each 8-bit input group as a matched bus and keep the two compared words synchronized at the device pins. Corresponding bits should have comparable rise and fall behavior to avoid presenting the comparator with unequal switching thresholds. Place any upstream bus buffers close enough to the SN74LS685N that transmission-line reflections and capacitive loading do not distort the relationship between the two operands.
The SN74LS685N uses inverted comparison outputs, so a designer who assumes active-high equal, greater-than, and less-than indications can invert the complete system decision. Build the polarity relationship directly from the manufacturer truth table and label the nets accordingly. Also confirm that the 20-pin NS package matches the board footprint; the DW family member has a different surface-mount package and is not a physical drop-in replacement.
Decouple the power supply at the comparator with the capacitance and placement specified by the manufacturer guidance for this package and operating environment. Keep switching-current return paths away from the input and output traces, especially when the device is mounted near relays, motor-control stages, or clocked logic. Confirm input levels against the actual LS-series thresholds because a 5 V-looking signal does not automatically satisfy every legacy TTL input specification.
Use the manufacturer's PDIP-20 land pattern and verify lead pitch, row spacing, drill size, and silkscreen orientation against the physical device before fabrication. A socket can improve serviceability in legacy equipment, but the selected socket must be electrically and mechanically suitable for the device's power and operating temperature. Avoid placing tall jumper wires or connectors where they can interfere with socketed replacement.
合規資訊
No specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement is identified for this exact ordering configuration. AEC-Q100 is not applicable unless a separate automotive-qualified ordering option is selected.