SN74HC682N 8-Bit Magnitude Comparator | Texas Instruments
MPN: SN74HC682N ✓ 啟用中SN74HC682N 概覽
直接替換替代品,適用於 SN74HC682N — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
SN74HC682NE4
✅ 直接替換📋 參考替代品(不在目錄中)
SN74HC682
✅ 直接替換📋 參考替代品(不在目錄中)
SN74HC682N 最大額定值與電氣特性
| Product Type | 8-bit identity and magnitude comparator |
| Input Word Width | 8 bits |
| Comparison Inputs | Two 8-bit words |
| Supported Data Formats | Binary or BCD |
| Equality Output | A=B, active low |
| Greater-Than Output | A>B, active low |
| Less-Than Output | A<B, active low |
| 輸出類型 | Three active-low comparison outputs |
| Logic Family | 74HC CMOS |
| Q Input Pull-Up Resistance | 100 kOhm |
| 封裝 | 20-pin plastic DIP |
| 腳位數 | 20 pins |
| 安裝類型 | Through-hole |
SN74HC682N 腳位配置
| 腳位 1 | A0 — Least-significant bit of input word A |
| 腳位 2 | A1 — Input word A bit 1 |
| 腳位 3 | A2 — Input word A bit 2 |
| 腳位 4 | A3 — Input word A bit 3 |
| 腳位 5 | A4 — Input word A bit 4 |
| 腳位 6 | A5 — Input word A bit 5 |
| 腳位 7 | A6 — Input word A bit 6 |
| 腳位 8 | A7 — Most-significant bit of input word A |
| 腳位 9 | B0 — Least-significant bit of input word B |
| 腳位 10 | B1 — Input word B bit 1 |
| 腳位 11 | B2 — Input word B bit 2 |
| 腳位 12 | B3 — Input word B bit 3 |
| 腳位 13 | B4 — Input word B bit 4 |
| 腳位 14 | B5 — Input word B bit 5 |
| 腳位 15 | B6 — Input word B bit 6 |
| 腳位 16 | B7 — Most-significant bit of input word B |
| 腳位 17 | Q0 — Q input with 100-kOhm pull-up termination |
| 腳位 18 | Q1 — Q input with 100-kOhm pull-up termination |
| 腳位 19 | A=B — Active-low equality output |
| 腳位 20 | A>B — Active-low greater-than output |
典型應用
SN74HC682N 適用於 6 應用s: Industrial Limit Comparison, Sorting and Ranking Control, Arithmetic Logic Unit Support, Address and Threshold Detection, Digital Metering and Display Control, Legacy Equipment Retrofit.
Industrial Limit Comparison
The SN74HC682N fits industrial limit-checking logic because it compares two complete 8-bit binary or BCD words and provides direct equality and ordering results. Connect one word to the A bus and the other to the B bus, then route the active-low A=B, A>B, or A<B output to the appropriate control stage. For a process controller, the comparator can determine whether a measured code has reached a programmed threshold without requiring a processor to perform every comparison cycle. The 20-pin through-hole package also simplifies maintenance on control boards that use sockets. Verify the device operating-temperature rating against the enclosure environment and account for active-low output behavior when defining trip or alarm polarity.
推薦
Sorting and Ranking Control
The SN74HC682N is useful in small sorting and ranking networks where two 8-bit items must be ordered quickly. Its A=B, A>B, and A<B outputs identify the relationship in parallel rather than requiring an iterative software comparison, reducing the number of logic stages needed to route operands. For multi-byte sorting, cascade multiple comparators and use the open-drain-style active-low result convention only where the electrical arrangement supports it. Confirm output timing and loading against the next HC-family stage. The SN74HC682N also provides 100-kOhm pull-up termination on the Q inputs, which should be considered when those inputs are driven from analog or switch sources rather than ordinary push-pull logic.
推薦
Arithmetic Logic Unit Support
The SN74HC682N can support magnitude-dependent decisions in a small arithmetic logic unit, particularly when the operands are already represented as 8-bit binary values. The comparator provides an immediate equality and ordering result alongside arithmetic operations, allowing control logic to branch on less-than, equal-to, or greater-than conditions. In a hardware accelerator, the result outputs can feed gating and status-latch logic without a software comparison loop. Check propagation delay against the surrounding arithmetic path and ensure that the selected supply voltage keeps all HC-family devices within their common input and output levels. The active-low outputs must be inverted where the ALU control architecture expects active-high condition signals.
推薦
Address and Threshold Detection
The SN74HC682N is appropriate for simple address-threshold detection where an 8-bit bus must be compared with a fixed or live 8-bit value. The equality output can indicate a selected address, while the ordering outputs can identify whether the bus value is above or below a threshold. This arrangement is useful in legacy automation, test fixtures, and equipment-control boards that use parallel logic rather than a programmable controller. Use pull-up or other required input arrangements only in accordance with the manufacturer circuit recommendations, and account for the 100-kOhm Q-input pull-up behavior when inputs originate from switches or analog sources. A high-impedance leakage path must not be allowed to create unintended bus activity.
推薦
Digital Metering and Display Control
The SN74HC682N can compare two 8-bit measurement or display codes for range decisions in digital panel systems. For example, it can identify whether a converted value equals a selected set point or lies above a limit, providing a hardware status indication alongside the displayed measurement. The 8-bit resolution is appropriate for coarse thresholds, alarm bands, and mode selection rather than high-resolution analog measurement. Because the Q inputs include 100-kOhm pull-up termination, analog switch or resistive network connections require careful leakage and continuity checks. Use the comparator output to set an alarm or display-enable stage, and verify that downstream display drivers operate from the same compatible logic supply.
推薦
Legacy Equipment Retrofit
The SN74HC682N is a practical choice when restoring or extending legacy digital equipment that uses leaded through-hole logic and requires a dedicated 8-bit comparison function. Its 20-pin plastic DIP package is easier to socket or replace than a surface-mount alternative in older control cards. A retrofit can use the comparator to reproduce a missing ordering decision, validate an input word, or generate an equality interlock. Before installation, verify the socket pinout, supply rails, signal levels, and any unusual use of the Q inputs because their 100-kOhm pull-ups can affect switch or analog interfaces. The design should also include suitable supply decoupling and protection for exposed legacy wiring.
推薦
推薦產品摘要
工程參考資料,適用於 SN74HC682N — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | SN74HC682NE4 | SN74HC682 |
|---|---|---|---|
| Package | 20-pin plastic DIP | 20-pin plastic DIP | 20-pin plastic DIP option |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Type | 8-bit identity and magnitude comparator | 8-bit identity and magnitude comparator | 8-bit identity and magnitude comparator |
| Input Width | 8 bits | 8 bits | 8 bits |
| Data Format | Binary or BCD | Binary or BCD | Binary or BCD |
| Comparison Outputs | A=B, A>B, and A<B; active low | A=B, A>B, and A<B; active low | A=B, A>B, and A<B; active low |
| Logic Family | 74HC CMOS | 74HC CMOS | 74HC CMOS |
| Q Input Pull-Up Resistance | 100 kOhm | 100 kOhm | 100 kOhm |
| Mounting Type | Through-hole | Through-hole | Through-hole option |
主要差異化特點
- Dedicated three-result magnitude comparison (對比SN74HC86N)
- Binary and BCD input compatibility (對比SN74HC682NE4)
- Integrated Q-input pull-up termination (對比SN74HC682)
設計說明
Treat A=B, A>B, and A<B as active-low signals rather than active-high status flags. A low output means the comparison is true. Connect these outputs directly only where the receiving logic expects the active-low convention or where wired logic is permitted; otherwise use an inverter. Also verify the final pin arrangement from the TI datasheet before layout because the comparator includes dedicated Q inputs in addition to the A and B buses.
Keep the SN74HC682N close to the logic that drives its A and B input buses and consumes the comparison outputs. Route these nets away from motor-control, relay, and switching-regator power paths to minimize coupled noise. Provide local supply decoupling close to the device using the capacitance and placement guidance in the manufacturer application information. Preserve a continuous ground-return path beneath or beside the DIP signal routing where the board layout permits.
Account for the 100-kOhm pull-up termination on the Q inputs when those pins receive signals from switches, resistive networks, or high-impedance analog sources. The pull-ups can alter threshold behavior and draw current whenever the Q net is driven low. Use the datasheet's recommended input network, avoid long exposed traces, and validate the final switching levels with the actual source impedance and cable length rather than treating the Q inputs as ordinary push-pull HC inputs.
合規資訊
Compliance declarations are not stated in the retrieved product information. Automotive qualification is not indicated for this logic IC.