SN74HC682N 8-Bit Magnitude Comparator | Texas Instruments
MPN: SN74HC682N ✓ Hoạt độngSN74HC682N Tóm tắt
Bộ thay thế dễ dàng lắp đặt cho SN74HC682N — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
SN74HC682NE4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SN74HC682
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SN74HC682N Tỷ lệ tối đa & tính chất điện
| Product Type | 8-bit identity and magnitude comparator |
| Input Word Width | 8 bits |
| Comparison Inputs | Two 8-bit words |
| Supported Data Formats | Binary or BCD |
| Equality Output | A=B, active low |
| Greater-Than Output | A>B, active low |
| Less-Than Output | A<B, active low |
| Kiểu đầu ra | Three active-low comparison outputs |
| Logic Family | 74HC CMOS |
| Q Input Pull-Up Resistance | 100 kOhm |
| Hộp | 20-pin plastic DIP |
| Số chân | 20 pins |
| Kiểu lắp đặt | Through-hole |
Cấu hình chân SN74HC682N
| Chân 1 | A0 — Least-significant bit of input word A |
| Chân 2 | A1 — Input word A bit 1 |
| Chân 3 | A2 — Input word A bit 2 |
| Chân 4 | A3 — Input word A bit 3 |
| Chân 5 | A4 — Input word A bit 4 |
| Chân 6 | A5 — Input word A bit 5 |
| Chân 7 | A6 — Input word A bit 6 |
| Chân 8 | A7 — Most-significant bit of input word A |
| Chân 9 | B0 — Least-significant bit of input word B |
| Chân 10 | B1 — Input word B bit 1 |
| Chân 11 | B2 — Input word B bit 2 |
| Chân 12 | B3 — Input word B bit 3 |
| Chân 13 | B4 — Input word B bit 4 |
| Chân 14 | B5 — Input word B bit 5 |
| Chân 15 | B6 — Input word B bit 6 |
| Chân 16 | B7 — Most-significant bit of input word B |
| Chân 17 | Q0 — Q input with 100-kOhm pull-up termination |
| Chân 18 | Q1 — Q input with 100-kOhm pull-up termination |
| Chân 19 | A=B — Active-low equality output |
| Chân 20 | A>B — Active-low greater-than output |
Ứng dụng tiêu biểu
SN74HC682N phù hợp cho 6 Áp dụngs: Industrial Limit Comparison, Sorting and Ranking Control, Arithmetic Logic Unit Support, Address and Threshold Detection, Digital Metering and Display Control, Legacy Equipment Retrofit.
Industrial Limit Comparison
The SN74HC682N fits industrial limit-checking logic because it compares two complete 8-bit binary or BCD words and provides direct equality and ordering results. Connect one word to the A bus and the other to the B bus, then route the active-low A=B, A>B, or A<B output to the appropriate control stage. For a process controller, the comparator can determine whether a measured code has reached a programmed threshold without requiring a processor to perform every comparison cycle. The 20-pin through-hole package also simplifies maintenance on control boards that use sockets. Verify the device operating-temperature rating against the enclosure environment and account for active-low output behavior when defining trip or alarm polarity.
Được đề xuất
Sorting and Ranking Control
The SN74HC682N is useful in small sorting and ranking networks where two 8-bit items must be ordered quickly. Its A=B, A>B, and A<B outputs identify the relationship in parallel rather than requiring an iterative software comparison, reducing the number of logic stages needed to route operands. For multi-byte sorting, cascade multiple comparators and use the open-drain-style active-low result convention only where the electrical arrangement supports it. Confirm output timing and loading against the next HC-family stage. The SN74HC682N also provides 100-kOhm pull-up termination on the Q inputs, which should be considered when those inputs are driven from analog or switch sources rather than ordinary push-pull logic.
Được đề xuất
Arithmetic Logic Unit Support
The SN74HC682N can support magnitude-dependent decisions in a small arithmetic logic unit, particularly when the operands are already represented as 8-bit binary values. The comparator provides an immediate equality and ordering result alongside arithmetic operations, allowing control logic to branch on less-than, equal-to, or greater-than conditions. In a hardware accelerator, the result outputs can feed gating and status-latch logic without a software comparison loop. Check propagation delay against the surrounding arithmetic path and ensure that the selected supply voltage keeps all HC-family devices within their common input and output levels. The active-low outputs must be inverted where the ALU control architecture expects active-high condition signals.
Được đề xuất
Address and Threshold Detection
The SN74HC682N is appropriate for simple address-threshold detection where an 8-bit bus must be compared with a fixed or live 8-bit value. The equality output can indicate a selected address, while the ordering outputs can identify whether the bus value is above or below a threshold. This arrangement is useful in legacy automation, test fixtures, and equipment-control boards that use parallel logic rather than a programmable controller. Use pull-up or other required input arrangements only in accordance with the manufacturer circuit recommendations, and account for the 100-kOhm Q-input pull-up behavior when inputs originate from switches or analog sources. A high-impedance leakage path must not be allowed to create unintended bus activity.
Được đề xuất
Digital Metering and Display Control
The SN74HC682N can compare two 8-bit measurement or display codes for range decisions in digital panel systems. For example, it can identify whether a converted value equals a selected set point or lies above a limit, providing a hardware status indication alongside the displayed measurement. The 8-bit resolution is appropriate for coarse thresholds, alarm bands, and mode selection rather than high-resolution analog measurement. Because the Q inputs include 100-kOhm pull-up termination, analog switch or resistive network connections require careful leakage and continuity checks. Use the comparator output to set an alarm or display-enable stage, and verify that downstream display drivers operate from the same compatible logic supply.
Được đề xuất
Legacy Equipment Retrofit
The SN74HC682N is a practical choice when restoring or extending legacy digital equipment that uses leaded through-hole logic and requires a dedicated 8-bit comparison function. Its 20-pin plastic DIP package is easier to socket or replace than a surface-mount alternative in older control cards. A retrofit can use the comparator to reproduce a missing ordering decision, validate an input word, or generate an equality interlock. Before installation, verify the socket pinout, supply rails, signal levels, and any unusual use of the Q inputs because their 100-kOhm pull-ups can affect switch or analog interfaces. The design should also include suitable supply decoupling and protection for exposed legacy wiring.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho SN74HC682N — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | SN74HC682NE4 | SN74HC682 |
|---|---|---|---|
| Package | 20-pin plastic DIP | 20-pin plastic DIP | 20-pin plastic DIP option |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Type | 8-bit identity and magnitude comparator | 8-bit identity and magnitude comparator | 8-bit identity and magnitude comparator |
| Input Width | 8 bits | 8 bits | 8 bits |
| Data Format | Binary or BCD | Binary or BCD | Binary or BCD |
| Comparison Outputs | A=B, A>B, and A<B; active low | A=B, A>B, and A<B; active low | A=B, A>B, and A<B; active low |
| Logic Family | 74HC CMOS | 74HC CMOS | 74HC CMOS |
| Q Input Pull-Up Resistance | 100 kOhm | 100 kOhm | 100 kOhm |
| Mounting Type | Through-hole | Through-hole | Through-hole option |
Bảo phân biệt quan trọng
- Dedicated three-result magnitude comparison (vsSN74HC86N)
- Binary and BCD input compatibility (vsSN74HC682NE4)
- Integrated Q-input pull-up termination (vsSN74HC682)
Ghi chú thiết kế
Treat A=B, A>B, and A<B as active-low signals rather than active-high status flags. A low output means the comparison is true. Connect these outputs directly only where the receiving logic expects the active-low convention or where wired logic is permitted; otherwise use an inverter. Also verify the final pin arrangement from the TI datasheet before layout because the comparator includes dedicated Q inputs in addition to the A and B buses.
Keep the SN74HC682N close to the logic that drives its A and B input buses and consumes the comparison outputs. Route these nets away from motor-control, relay, and switching-regator power paths to minimize coupled noise. Provide local supply decoupling close to the device using the capacitance and placement guidance in the manufacturer application information. Preserve a continuous ground-return path beneath or beside the DIP signal routing where the board layout permits.
Account for the 100-kOhm pull-up termination on the Q inputs when those pins receive signals from switches, resistive networks, or high-impedance analog sources. The pull-ups can alter threshold behavior and draw current whenever the Q net is driven low. Use the datasheet's recommended input network, avoid long exposed traces, and validate the final switching levels with the actual source impedance and cable length rather than treating the Q inputs as ordinary push-pull HC inputs.
Thông tin tuân thủ
Compliance declarations are not stated in the retrieved product information. Automotive qualification is not indicated for this logic IC.