SP3232EBEP-L - 250kbps RS-232 Transceiver | MaxLinear
MPN: SP3232EBEP-L ✓ 啟用中SP3232EBEP-L 概覽
An RS-232 transceiver is an interface IC that translates between complementary logic-level signals used by digital equipment and the positive and negative voltage levels used by RS-232 links. The SP3232EB belongs to the broader interface IC hierarchy, where it sits between a host controller or UART and an external serial connector. This integration reduces the number of external level-shifting and charge-pump components required in compact portable equipment.
Key features include a 2/2 transceiver arrangement, true RS-232 operation from +3.0V to +5.5V, and a maximum data rate of 250kbps when fully loaded. The high-efficiency on-board charge pump produces approximately ±5.5V from one supply. This makes the device applicable to 3.3V-only, mixed 3.3V-to-5.5V, and 5.0V-only systems. The device is intended specifically for portable and hand-held equipment such as notebook and laptop computers.
The SP3232EB family combines charge-pump generation, RS-232 drivers, and RS-232 receivers in one package. Its dual-channel architecture allows two serial data paths to be implemented without duplicating the interface circuitry. The 16-pin PDIP package also supports conventional through-hole PCB assembly and prototyping. Because RS-232 is a single-ended, bipolar interface, correct grounding, cable routing, and protection remain important in systems exposed to electrostatic discharge or long cables.
Typical uses include portable computer serial ports, industrial control links, embedded equipment, point-of-sale terminals, and service interfaces. The device is particularly useful when the system logic operates at 3.3V but the attached peripheral requires true RS-232 signal levels. Its 250kbps capability is suitable for moderate-speed data transfer while consuming less board area than a discrete driver and receiver implementation.
Designers should place the required charge-pump capacitors close to their associated pins and provide the input and output bypassing specified by the manufacturer datasheet. Keep protected RS-232 traces away from sensitive clock, audio, and sensor paths. Confirm connector pin assignments and logic polarity during system integration, since transmitter and receiver signal inversions can differ from UART logic conventions.
This product page combines manufacturer specifications, application guidance, package details, and verified drop-in replacement information to support faster component selection. It also distinguishes electrically similar devices from replacements that are truly pin-compatible, helping engineers preserve the existing 16-pin PDIP footprint and validate interface behavior before releasing a new board.
直接替換替代品,適用於 SP3232EBEP-L — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: SP3232EBEP-L (相同外形與佔位) — 差異在於 Charge-Pump Capacitor Requirement, Package, Mounting Type, Product Type, Maximum Data Rate.
SP3232EBEP
✅ 直接替換📋 參考替代品(不在目錄中)
SP3232EEA-L
✅ 直接替換聯絡詢價
查看資料表 →SP3232EUEA-L/TR
✅ 直接替換聯絡詢價
查看資料表 →SP3232EBEP-L 規格
| Product Type | RS-232 transceiver IC |
| Number of Transmitters | 2 |
| Number of Receivers | 2 |
| Supply Voltage Range | +3.0V to +5.5V |
| Maximum Data Rate | 250kbps |
| Charge-Pump Output | ±5.5V |
| Charge-Pump Capacitor Requirement | 0.1uF in 3.3V operation |
| Transceiver Configuration | 2/2 full RS-232 |
| 封裝 | 16-pin PDIP |
| 安裝類型 | Through-hole |
| Power-Supply Architecture | On-board charge-pump supply |
| Supported Logic Supply | 3.3V and 5.0V systems |
SP3232EBEP-L 16-pin pdip 腳位配置指南
SP3232EBEP-L(16-pin pdip 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: SP3232EBEP-L.
請參閱 資料表 以查看完整腳位配置。
典型應用
SP3232EBEP-L 適用於 6 應用s: Portable Computer Serial Interface, Industrial Serial Control Link, Point-of-Sale Terminal Interface, Embedded Equipment Service Port, Data Acquisition and Test Equipment, Network and Communication Equipment.
Portable Computer Serial Interface
The SP3232EBEP-L fits a portable or hand-held computer that needs a true RS-232 port while operating from a 3.3V logic supply. Its integrated charge pump generates approximately ±5.5V from +3.0V to +5.5V and requires only 0.1uF capacitors in 3.3V operation, reducing external power circuitry. Two transmitters and two receivers support two serial paths through the 16-pin PDIP interface. The 250kbps rate is appropriate for moderate-speed peripheral communication, while the through-hole package simplifies prototype assembly and repair.
推薦
Industrial Serial Control Link
The SP3232EBEP-L can bridge a 3.3V or 5V controller to equipment that requires true RS-232 levels. Its two-channel transceiver arrangement provides dedicated transmit and receive paths, while the integrated charge pump avoids a separate negative-voltage supply. At rates up to 250kbps, it is suitable for configuration links, service ports, and moderate-speed equipment control. Designers should assess cable length, grounding, and connector protection because the transceiver rating alone does not define the complete industrial-port withstand rating.
推薦
Point-of-Sale Terminal Interface
A point-of-sale terminal or peripheral using RS-232 can benefit from the SP3232EBEP-L because the transceiver supports both 3.3V-only and 5.0V-only systems. The single-supply charge pump supplies the bipolar RS-232 levels, while the 0.1uF 3.3V capacitor requirement helps conserve board area. Two transmitters and two receivers allow compact multi-port designs. The 250kbps rate is suitable for transaction peripherals that exchange commands and short data records rather than continuous high-bandwidth streams.
推薦
Embedded Equipment Service Port
The SP3232EBEP-L is useful for manufacturing and field-service access on embedded equipment that retains a legacy RS-232 console. A 3.3V system can obtain true RS-232 levels without adding a negative rail, and the 16-pin PDIP package is convenient for through-hole service boards. The dual transmitter and dual receiver arrangement supports two channels. Keep the port disabled or appropriately configured when unused, and verify connector wiring against the datasheet pin table to avoid logic-polarity errors during maintenance.
推薦
Data Acquisition and Test Equipment
The SP3232EBEP-L can serve as the RS-232 interface in data-acquisition and test equipment that uses a 3.3V controller but must communicate with a true RS-232 instrument. The integrated charge pump provides approximately ±5.5V output levels, and the maximum 250kbps rate supports moderate-speed command and result transfers. Use controlled grounding and short, shielded cabling where appropriate. The 16-pin PDIP package is also practical for instrument-control boards that favor conventional through-hole assembly.
推薦
Network and Communication Equipment
The SP3232EBEP-L can provide legacy RS-232 connectivity in network or communication equipment with a modern 3.3V supply. Its two transmitters and two receivers support independent RS-232 channels, and the integrated charge pump simplifies system power design by avoiding a separate negative supply. The 250kbps capability is adequate for management interfaces and low-rate data links. Designers should separate the RS-232 routing from Ethernet or radio sections to prevent charge-pump noise and cable transients from affecting sensitive circuitry.
推薦
推薦產品摘要
工程參考資料,適用於 SP3232EBEP-L — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | SP3232EBEP | SP3232EEA-L | SP3232EUEA-L |
|---|---|---|---|---|
| Brand | MaxLinear | MaxLinear | MaxLinear | MaxLinear |
| Package | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP |
| Device Type | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver |
| Number of Transmitters | 2 | 2 | 2 | 2 |
| Number of Receivers | 2 | 2 | 2 | 2 |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole |
主要差異化特點
- True RS-232 operation from a modern 3.3V supply (對比SP3232EBEP)
- Compact integrated charge-pump implementation (對比SP3232EEA-L)
- Two-channel RS-232 interface in a 16-pin PDIP (對比SP3232EUEA-L)
設計說明
Place the 0.1uF charge-pump capacitors close to the pins and capacitor connections identified in the manufacturer datasheet. Keep these high-current switched paths compact and away from UART, crystal, analog, and sensor traces. Use the manufacturer layout as the starting point, and verify the physical pin numbering against the 16-pin PDIP footprint before fabrication.
Decouple the supply near the device with the capacitance and connection arrangement specified in the datasheet. The SP3232EBEP-L can operate from +3.0V to +5.5V and produces approximately ±5.5V through its charge pump. Do not power the RS-232 interface from a rail that can exceed +5.5V, and include local bulk capacitance where the source impedance could otherwise disturb the charge pump.
Confirm transmit and receive logic polarity against the UART and connector schematic; RS-232 transmitter inputs and receiver outputs are not always identified using the same active-level convention as the host logic. Also verify whether the unused driver input and receiver output must be left unconnected or biased according to the manufacturer pin table. Avoid selecting a replacement solely by the 16-pin outline.
Route RS-232 traces away from clocks, reset lines, sensitive analog inputs, and other high-impedance nodes. For external cables, use the shortest practical ground reference and consider connector-side transient protection. The IC's 250kbps capability is a device rating, while usable cable distance also depends on baud rate, capacitance, loading, shielding, and the grounding arrangement.
合規資訊
The manufacturer datasheet confirms the electrical and package family characteristics, but the available product information does not explicitly establish RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for this exact ordering code.