MaxLinear

SP3232EBEP-L - 250kbps RS-232 Transceiver | MaxLinear

MPN: SP3232EBEP-L ✓ فعال
+3.0V to +5.5V Vdss 16-pin PDIP Package
حداقل سفارش: 1 |

SP3232EBEP-L نمای کلی

The MaxLinear SP3232EBEP-L is a true +3.0V to +5.5V RS-232 transceiver IC with two transmitters and two receivers, data rates up to 250kbps, and a 16-pin PDIP package. Its integrated charge-pump supply generates the bipolar voltage levels required by RS-232 from a single supply, while 0.1uF charge-pump capacitors support operation from a 3.3V rail.

An RS-232 transceiver is an interface IC that translates between complementary logic-level signals used by digital equipment and the positive and negative voltage levels used by RS-232 links. The SP3232EB belongs to the broader interface IC hierarchy, where it sits between a host controller or UART and an external serial connector. This integration reduces the number of external level-shifting and charge-pump components required in compact portable equipment.

Key features include a 2/2 transceiver arrangement, true RS-232 operation from +3.0V to +5.5V, and a maximum data rate of 250kbps when fully loaded. The high-efficiency on-board charge pump produces approximately ±5.5V from one supply. This makes the device applicable to 3.3V-only, mixed 3.3V-to-5.5V, and 5.0V-only systems. The device is intended specifically for portable and hand-held equipment such as notebook and laptop computers.

The SP3232EB family combines charge-pump generation, RS-232 drivers, and RS-232 receivers in one package. Its dual-channel architecture allows two serial data paths to be implemented without duplicating the interface circuitry. The 16-pin PDIP package also supports conventional through-hole PCB assembly and prototyping. Because RS-232 is a single-ended, bipolar interface, correct grounding, cable routing, and protection remain important in systems exposed to electrostatic discharge or long cables.

Typical uses include portable computer serial ports, industrial control links, embedded equipment, point-of-sale terminals, and service interfaces. The device is particularly useful when the system logic operates at 3.3V but the attached peripheral requires true RS-232 signal levels. Its 250kbps capability is suitable for moderate-speed data transfer while consuming less board area than a discrete driver and receiver implementation.

Designers should place the required charge-pump capacitors close to their associated pins and provide the input and output bypassing specified by the manufacturer datasheet. Keep protected RS-232 traces away from sensitive clock, audio, and sensor paths. Confirm connector pin assignments and logic polarity during system integration, since transmitter and receiver signal inversions can differ from UART logic conventions.

This product page combines manufacturer specifications, application guidance, package details, and verified drop-in replacement information to support faster component selection. It also distinguishes electrically similar devices from replacements that are truly pin-compatible, helping engineers preserve the existing 16-pin PDIP footprint and validate interface behavior before releasing a new board.

جایگزین‌های drop-in برای SP3232EBEP-L — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای SP3232EBEP-L (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Charge-Pump Capacitor Requirement, Package, Mounting Type, Product Type, Maximum Data Rate.

MaxLinear
Charge-Pump Capacitor Requirement: 0.1 µF at 3.3 V
Package: 16-pin SSOP
Mounting Type: Surface mount
مقایسه با SP3232EBEP-L →
MaxLinear
Charge-Pump Capacitor Requirement: 0.1 µF at 3.3 V operation
Package: 16-SSOP
Mounting Type: Surface mount

SP3232EBEP

✅ جایگزین مستقیم
📦 16-pin PDIP
Same SP3232EB family and 16-pin PDIP format; ordering-suffix environmental and lead-finish differences require verification, with no verified change to the 250kbps data rate.

📋 جایگزین مرجع (خارج از کاتالوگ)

SP3232EEA-L

✅ جایگزین مستقیم
MaxLinear
📦 16-pin PDIP
RS-232 transceiver IC · 2 transmitters and 2 receivers · 120 kbps minimum under full load · 3 V to 5.5 V · 1 mA · 1 µA · 0.1 µF at 3.3 V · -40°C to +85°C

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

SP3232EUEA-L/TR

✅ جایگزین مستقیم
MaxLinear
📦 16-pin PDIP
RS-232 transceiver · 2 · 2 · 1000 kbps · 3.3 V · 3 V to 5.5 V · 0.1 µF at 3.3 V operation · 16-SSOP

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

SP3232EBEP-L مشخصات

Product Type RS-232 transceiver IC
Number of Transmitters 2
Number of Receivers 2
Supply Voltage Range +3.0V to +5.5V
Maximum Data Rate 250kbps
Charge-Pump Output ±5.5V
Charge-Pump Capacitor Requirement 0.1uF in 3.3V operation
Transceiver Configuration 2/2 full RS-232
بسته‌بندی 16-pin PDIP
نوع نصب Through-hole
Power-Supply Architecture On-board charge-pump supply
Supported Logic Supply 3.3V and 5.0V systems

راهنمای پیکربندی پین SP3232EBEP-L 16-pin pdip

پیکربندی پین برای SP3232EBEP-L (پکیج 16-pin pdip). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 16-pin pdip برای SP3232EBEP-L

داده پین‌آوت تفصیلی موجود نیست برای SP3232EBEP-L.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

SP3232EBEP-L مناسب است برای 6 کاربردs: Portable Computer Serial Interface, Industrial Serial Control Link, Point-of-Sale Terminal Interface, Embedded Equipment Service Port, Data Acquisition and Test Equipment, Network and Communication Equipment.

📱

Portable Computer Serial Interface

The SP3232EBEP-L fits a portable or hand-held computer that needs a true RS-232 port while operating from a 3.3V logic supply. Its integrated charge pump generates approximately ±5.5V from +3.0V to +5.5V and requires only 0.1uF capacitors in 3.3V operation, reducing external power circuitry. Two transmitters and two receivers support two serial paths through the 16-pin PDIP interface. The 250kbps rate is appropriate for moderate-speed peripheral communication, while the through-hole package simplifies prototype assembly and repair.

🏭

Industrial Serial Control Link

The SP3232EBEP-L can bridge a 3.3V or 5V controller to equipment that requires true RS-232 levels. Its two-channel transceiver arrangement provides dedicated transmit and receive paths, while the integrated charge pump avoids a separate negative-voltage supply. At rates up to 250kbps, it is suitable for configuration links, service ports, and moderate-speed equipment control. Designers should assess cable length, grounding, and connector protection because the transceiver rating alone does not define the complete industrial-port withstand rating.

🖥️

Point-of-Sale Terminal Interface

A point-of-sale terminal or peripheral using RS-232 can benefit from the SP3232EBEP-L because the transceiver supports both 3.3V-only and 5.0V-only systems. The single-supply charge pump supplies the bipolar RS-232 levels, while the 0.1uF 3.3V capacitor requirement helps conserve board area. Two transmitters and two receivers allow compact multi-port designs. The 250kbps rate is suitable for transaction peripherals that exchange commands and short data records rather than continuous high-bandwidth streams.

🔧

Embedded Equipment Service Port

The SP3232EBEP-L is useful for manufacturing and field-service access on embedded equipment that retains a legacy RS-232 console. A 3.3V system can obtain true RS-232 levels without adding a negative rail, and the 16-pin PDIP package is convenient for through-hole service boards. The dual transmitter and dual receiver arrangement supports two channels. Keep the port disabled or appropriately configured when unused, and verify connector wiring against the datasheet pin table to avoid logic-polarity errors during maintenance.

📡

Data Acquisition and Test Equipment

The SP3232EBEP-L can serve as the RS-232 interface in data-acquisition and test equipment that uses a 3.3V controller but must communicate with a true RS-232 instrument. The integrated charge pump provides approximately ±5.5V output levels, and the maximum 250kbps rate supports moderate-speed command and result transfers. Use controlled grounding and short, shielded cabling where appropriate. The 16-pin PDIP package is also practical for instrument-control boards that favor conventional through-hole assembly.

🌐

Network and Communication Equipment

The SP3232EBEP-L can provide legacy RS-232 connectivity in network or communication equipment with a modern 3.3V supply. Its two transmitters and two receivers support independent RS-232 channels, and the integrated charge pump simplifies system power design by avoiding a separate negative supply. The 250kbps capability is adequate for management interfaces and low-rate data links. Designers should separate the RS-232 routing from Ethernet or radio sections to prevent charge-pump noise and cable transients from affecting sensitive circuitry.

خلاصه محصولات پیشنهادی

SP3232EBEP Same-family SP3232EB interface in the same 16-pin PDIP format استفاده‌شده در: Portable Computer Serial Interface, Embedded Equipment Service Port, Data Acquisition and Test Equipment SP3232EEA-L MaxLinear استفاده‌شده در: Industrial Serial Control Link, Network and Communication Equipment SP3232EUEA-L MaxLinear SP3232E-family RS-232 interface candidate استفاده‌شده در: Point-of-Sale Terminal Interface
What is the SP3232EBEP-L?
The SP3232EBEP-L is a two-transmitter, two-receiver RS-232 transceiver IC for portable and hand-held equipment. According to the MaxLinear SP3222EB/SP3232EB datasheet, its integrated charge-pump supply operates from a single +3.0V to +5.5V source and supports data rates up to 250kbps. The device is supplied in a 16-pin PDIP package for through-hole PCB assembly.
What is the operating voltage of SP3232EBEP-L?
The SP3232EBEP-L operates from a single +3.0V to +5.5V supply. The manufacturer datasheet identifies 3.3V-only, mixed 3.3V-to-5.5V, and 5.0V-only systems as suitable operating environments. At 3.3V, the integrated charge pump requires only 0.1uF capacitors and generates the bipolar voltage needed for true RS-232 operation.
What is the maximum data rate of SP3232EBEP-L?
The SP3232EBEP-L supports data rates up to 250kbps when fully loaded. This rating allows the interface to handle moderate-speed serial traffic while still producing true RS-232 levels from a 3.0V-to-5.5V supply. System timing, cable length, loading, and signal-integrity losses should also be checked rather than assuming the maximum rate applies to every connection.
Where can I download the SP3232EBEP-L datasheet PDF?
The official SP3222EB/SP3232EB datasheet PDF is available from MaxLinear at https://www.maxlinear.com/ds/sp3222eb_sp3232eb.pdf. It is the preferred document for the charge-pump capacitor arrangement, absolute maximum ratings, electrical characteristics, timing, and package details. Use the exact SP3232EBEP-L ordering code when checking lead and temperature options.
Where is the SP3232EBEP-L pinout?
The SP3232EBEP-L pinout is shown in the pin configuration section of the MaxLinear SP3222EB/SP3232EB datasheet. The SP3232EBEP-L uses a 16-pin PDIP outline, with transmit inputs, receive outputs, supply pins, charge-pump nodes, and ground assignments identified by the manufacturer. Use that table when assigning PCB nets and verifying connector wiring.
What can replace the SP3232EBEP-L?
The closest documented same-family drop-in candidate is SP3232EBEP, which uses the same 16-pin PDIP interface format and belongs to the same SP3232EB family. Confirm temperature grade, lead finish, electrical ratings, and exact pin assignments before substitution. The available cross-reference results do not establish enough additional pin-compatible alternatives to claim a broader replacement set.
Is SP3232EBEP-L suitable for a 3.3V system?
Yes, the SP3232EBEP-L is suitable for a 3.3V system because its specified supply range begins at +3.0V. The integrated charge pump produces true RS-232 levels using only 0.1uF capacitors in 3.3V operation. Place those capacitors close to the designated pins and follow the manufacturer datasheet layout and bypass recommendations.
How does the SP3232EBEP-L generate negative RS-232 voltage?
The SP3232EBEP-L uses an on-board charge-pump supply to generate approximately ±5.5V from one +3.0V-to-+5.5V source. The charge pump requires only 0.1uF capacitors in 3.3V operation, reducing external component count compared with a discrete RS-232 level-shifting design. Charge-pump components must follow the specified layout to minimize switching noise and output disturbance.
What is the difference between SP3232EBEP-L and SP3232EBEP?
SP3232EBEP-L and SP3232EBEP are members of the same SP3232EB RS-232 transceiver family and are associated with the 16-pin PDIP package. The available manufacturer information does not expose a complete ordering-code comparison for this distinction. Before interchange, verify the pinout, operating-temperature range, lead finish, and lot-specific ordering requirements in the datasheet.
When should I choose SP3232EBEP-L instead of SP3232EBEP?
Choose SP3232EBEP-L when its exact ordering options, environmental grade, and lead configuration match the production requirement while retaining the SP3232EB 16-pin PDIP interface. Choose SP3232EBEP only after checking the manufacturer ordering table against the installed board. Both devices share the family architecture, so the decisive factors are traceability, qualification, and exact suffix compatibility.
Is SP3232EBEP-L in stock and what is its lead time?
Current stock and lead time should be requested through the Request a Quote form on this page. The product is listed by the manufacturer as part of the SP3232EB family, but live inventory and production scheduling can change independently of lifecycle information. Provide the required quantity, package suffix, date code, and inspection requirements when requesting a quotation.
How much does SP3232EBEP-L cost?
The current unit price for SP3232EBEP-L should be obtained through the Request a Quote form on this page. Quote requests should state the required quantity, acceptable date-code range, and whether a 16-pin PDIP package is mandatory. The displayed pricing structure is designed to reflect current quantity and sourcing conditions rather than a static historical price.
Where can I buy SP3232EBEP-L online?
Use the Request a Quote form on this page to request SP3232EBEP-L availability, current pricing, and lead time. Specify whether the 16-pin PDIP package and exact ordering suffix are required. The manufacturer datasheet and product links on this page provide the appropriate technical references for qualifying the component before procurement.
What are the key specifications of SP3232EBEP-L that engineers should know?
The essential specifications are a +3.0V-to-+5.5V supply range, 250kbps maximum data rate, two transmitters, two receivers, approximately ±5.5V charge-pump output, and a 16-pin PDIP package. According to the MaxLinear datasheet, 3.3V operation requires only 0.1uF charge-pump capacitors. These parameters make the IC suitable for compact true-RS-232 ports operating from modern 3.3V logic rails.
Does SP3232EBEP-L include ESD protection?
The RS-232 interface includes protection features, but the exact SP3232EBEP-L ESD rating should be confirmed in the MaxLinear SP3222EB/SP3232EB datasheet before assigning a system-level surge rating. Connector protection is still recommended when cables leave the enclosure. The rating of the IC is not automatically the withstand rating of the complete external port.
Can a cross-brand part replace SP3232EBEP-L without a PCB change?
A cross-brand replacement should be selected only after its schematic, package drawing, pin numbers, charge-pump connections, supply range, and electrical characteristics match the SP3232EBEP-L. The available cross-reference results do not identify a verified cross-brand part that meets all of those conditions. Changing manufacturers without a documented pin-for-pin comparison risks incorrect charge-pump connection or incompatible interface behavior.

داده‌های مرجع مهندسی برای SP3232EBEP-L — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose SP3232EBEP-L for a new or replacement design that requires true RS-232 levels from a +3.0V-to-+5.5V supply, uses a 16-pin PDIP footprint, and needs up to 250kbps operation. Its integrated charge pump is especially useful in 3.3V systems because it requires only 0.1uF capacitors in 3.3V operation. Select SP3232EBEP when that same-family ordering code meets the board's environmental, traceability, and lead-finish requirements. Consider SP3232EEA-L or SP3232EUEA-L only after comparing the exact pin assignments, electrical characteristics, and ordering suffix in the manufacturer documentation. None of the listed candidates should be treated as an automatic substitution based only on package shape.

مقایسه با جایگزین‌ها

پارامتر این محصول SP3232EBEP SP3232EEA-L SP3232EUEA-L
Brand MaxLinear MaxLinear MaxLinear MaxLinear
Package 16-pin PDIP 16-pin PDIP 16-pin PDIP 16-pin PDIP
Device Type RS-232 transceiver RS-232 transceiver RS-232 transceiver RS-232 transceiver
Number of Transmitters 2 2 2 2
Number of Receivers 2 2 2 2
Mounting Type Through-hole Through-hole Through-hole Through-hole

تفاوت‌های کلیدی

  • True RS-232 operation from a modern 3.3V supply (در مقابلSP3232EBEP)
  • Compact integrated charge-pump implementation (در مقابلSP3232EEA-L)
  • Two-channel RS-232 interface in a 16-pin PDIP (در مقابلSP3232EUEA-L)

یادداشت‌های طراحی

Place the 0.1uF charge-pump capacitors close to the pins and capacitor connections identified in the manufacturer datasheet. Keep these high-current switched paths compact and away from UART, crystal, analog, and sensor traces. Use the manufacturer layout as the starting point, and verify the physical pin numbering against the 16-pin PDIP footprint before fabrication.

Decouple the supply near the device with the capacitance and connection arrangement specified in the datasheet. The SP3232EBEP-L can operate from +3.0V to +5.5V and produces approximately ±5.5V through its charge pump. Do not power the RS-232 interface from a rail that can exceed +5.5V, and include local bulk capacitance where the source impedance could otherwise disturb the charge pump.

Confirm transmit and receive logic polarity against the UART and connector schematic; RS-232 transmitter inputs and receiver outputs are not always identified using the same active-level convention as the host logic. Also verify whether the unused driver input and receiver output must be left unconnected or biased according to the manufacturer pin table. Avoid selecting a replacement solely by the 16-pin outline.

Route RS-232 traces away from clocks, reset lines, sensitive analog inputs, and other high-impedance nodes. For external cables, use the shortest practical ground reference and consider connector-side transient protection. The IC's 250kbps capability is a device rating, while usable cable distance also depends on baud rate, capacitance, loading, shielding, and the grounding arrangement.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The manufacturer datasheet confirms the electrical and package family characteristics, but the available product information does not explicitly establish RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for this exact ordering code.

تاریخ تأیید داده‌ها: 2026-11-10 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

SP3232EBEP-L datasheet SP3232EBEP-L datasheet pdf SP3232EBEP-L pinout SP3232EBEP-L schematic SP3232EBEP-L equivalent SP3232EBEP-L replacement SP3232EBEP-L drop-in replacement SP3232EBEP-L price SP3232EBEP-L stock MaxLinear SP3232EBEP-L SP3232EBEP-L 16-PDIP SP3232EBEP-L 250kbps RS-232 SP3232EBEP-L vs SP3232EBEP SP3232EBEP-L 3.3V application

قطعات و اصطلاحات مرتبط

MaxLinear SP3232EBEP-L SP3232EBEP SP3232EEA-L SP3232EUEA-L SP3232EB RS-232 transceiver interface IC transceiver RS-232 UART charge pump bipolar voltage 250kbps 3.3V logic 16-pin PDIP through-hole package surface mount semiconductor portable equipment industrial control point-of-sale terminal test equipment RS-232 driver RS-232 receiver
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ