SY89296UTI - 1.5GHz LVPECL 1024-Tap Delay Line | Microchip
MPN: SY89296UTI ✓ 啟用中SY89296UTI 概覽
A programmable delay line is a timing-control semiconductor that inserts a calibrated interval between an incoming signal and its output. Within the broader clock and timing hierarchy, it combines a clock-and-timing IC with a digitally controlled delay element. The SY89296U supports precise phase alignment, delay compensation, and signal-path timing calibration in systems where fixed propagation delay is insufficient.
Key features include 1,024 discrete delay taps, a 10 ps digital delay increment, a 10-bit delay control word, and a separate D[10] cascade-control bit. The input and inverted input default to an equivalent low state when left floating. An additional 11th control bit permits simultaneous cascading of SY89296U devices for a larger delay range. The analog fine-tune function adds approximately 40 ps of continuous adjustment to the digitally selected delay.
The SY89296U uses LVPECL-compatible high-speed differential signaling for 2.5 V or 3.3 V operation. Its input bandwidth reaches 1.5 GHz, allowing it to operate as a programmable phase-shifting element rather than merely a low-frequency timing delay. The combination of 10 ps digital steps and analog fine tuning supports both coarse alignment across a wide interval and fine adjustment within one digital step.
Typical uses include clock and data recovery timing compensation, high-speed serial-interface phase alignment, telecommunications timing adjustment, instrumentation synchronization, and automated test equipment. In each case, engineers use the digital control bits to select a coarse delay and then use the fine-tune control for precision calibration when fixed clock distribution alone cannot accommodate propagation, skew, or board-timing variation.
PCB implementation requires careful treatment of differential clock signals and their return paths. The SY89296UTI should be placed close to the circuit requiring phase adjustment, with short and symmetrically routed differential traces, solid ground-plane reference, and minimal stubs. Power and ground connections must follow the pin-description and layout guidance in the manufacturer datasheet. Termination values and decoupling should be selected from the circuit conditions rather than estimated from nominal voltage alone.
This page consolidates the manufacturer’s programming architecture, delay-resolution details, interface information, and practical PCB considerations into an engineering-focused guide. It also distinguishes the SY89296UTI from a verified drop-in replacement list, avoiding unsupported substitutions that could compromise LVPECL timing, control compatibility, or the 32-pin footprint.
直接替換替代品,適用於 SY89296UTI — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此產品無可直接替換的替代品。
申請替代品SY89296UTI 規格
| Product Type | Precision LVPECL programmable delay-line IC |
| Maximum Operating Frequency | 1.5 GHz |
| Minimum Programmable Delay | 3.2 ns |
| Maximum Programmable Delay | 14.8 ns |
| Delay Resolution | 10 ps per digital step |
| Number of Taps | 1,024 taps |
| Digital Delay Control Word | 10 bits |
| Cascade Control | D[10] control bit for simultaneous cascading |
| Analog Fine-Tune Range | Approximately 40 ps |
| 供應電壓 | 2.5 V or 3.3 V |
| Output Logic | LVPECL |
| Input Signal | Differential input with IN and /IN pins |
| Floating Input State | IN and /IN default to an equivalent low state |
| 封裝 | 32-pin TQFP |
| 安裝類型 | Surface mount |
SY89296UTI 32-pin tqfp 腳位配置指南
SY89296UTI(32-pin tqfp 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: SY89296UTI.
請參閱 資料表 以查看完整腳位配置。
典型應用
SY89296UTI 適用於 6 應用s: High-Speed Clock Phase Alignment, Telecommunications Timing Compensation, Data Recovery Path Timing, Precision Test and Measurement, Automated Semiconductor Test Systems, Industrial Synchronization Networks.
High-Speed Clock Phase Alignment
The SY89296UTI fits clock-phase alignment systems that require programmable correction after board assembly. Its 1,024 digital taps cover a 3.2 ns to 14.8 ns delay range, with each control-word increment adding 10 ps, while the analog fine-tune input provides approximately 40 ps of continuous adjustment. Place the device near the clock-consuming circuit, route the differential LVPECL paths symmetrically, and use the coarse digital steps before applying fine calibration. This approach allows a single clock-distribution design to compensate for propagation, skew, or component variation without relocating the clock source.
推薦
Telecommunications Timing Compensation
The SY89296UTI supports telecommunications timing compensation where serial links or recovered clocks need adjustable timing rather than a fixed propagation interval. Its 1.5 GHz operating frequency and 10 ps digital delay resolution suit high-speed timing paths, while LVPECL signaling supports differential distribution on suitable circuit boards. Use the 3.2 ns to 14.8 ns programmable range for coarse timing correction and the approximately 40 ps fine-tune range for calibration. Preserve impedance continuity, minimize trace stubs, and follow the manufacturer termination and decoupling guidance.
推薦
Data Recovery Path Timing
The SY89296UTI can be inserted into a high-speed data-recovery path to create a controlled phase relationship between data and clock. The 1,024-tap architecture provides 10 ps nominal resolution across a 3.2 ns to 14.8 ns interval, allowing calibration to compensate for trace and component delay. Analog fine tuning of approximately 40 ps supports the final setup-and-hold adjustment when digital increments alone are too coarse. Keep the device close to the receiving logic, use short differential routes with continuous reference planes, and validate eye margin after every timing change.
推薦
Precision Test and Measurement
The SY89296UTI is appropriate for instrumentation requiring a repeatable, digitally selectable delay in a calibration or synchronization path. The 10 ps control-word increments permit deterministic settings across 1,024 taps, while analog fine tuning enables sub-step adjustment over approximately 40 ps. Use the device in a controlled-temperature fixture when measurement accuracy depends on timing repeatability, and document the control-word value for each calibration point. Differential LVPECL routing and clean supplies help isolate the delay-line behavior from jitter introduced by the surrounding test system.
推薦
Automated Semiconductor Test Systems
The SY89296UTI supports automated test systems that need digitally controlled timing adjustment for device characterization or load-board synchronization. Its 1,024 discrete settings and 10 ps steps allow test recipes to select repeatable delay values, while the 3.2 ns to 14.8 ns range addresses common interconnect and fixture timing offsets. Position the delay line near the device-under-test interface to limit additional trace uncertainty. Control the analog fine-tune input carefully during calibration because it permits continuous adjustment of approximately 40 ps beyond the digital setting.
推薦
Industrial Synchronization Networks
The SY89296UTI fits industrial synchronization networks where distributed equipment requires a configurable timing offset. Its 1.5 GHz capability and 10 ps digital resolution permit precise alignment of high-speed control or communication clocks, while the LVPECL interface supports differential signaling over controlled PCB routes. Program the coarse delay through the 10-bit control word, then use the approximately 40 ps analog range for production calibration. Validate timing over the complete environmental range and isolate the device from sources of switching noise that could obscure the intended phase relationship.
推薦
推薦產品摘要
工程參考資料,適用於 SY89296UTI — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Brand | Microchip Technology |
| Package | 32-pin TQFP |
| Product Type | Precision LVPECL programmable delay-line IC |
| Maximum Operating Frequency | 1.5 GHz |
| Programmable Delay Range | 3.2 ns to 14.8 ns |
| Digital Delay Increment | 10 ps |
| Number of Taps | 1,024 taps |
| Digital Control Word | 10 bits |
| Analog Fine-Tune Range | Approximately 40 ps |
| Supply Voltage | 2.5 V or 3.3 V |
| Output Logic | LVPECL |
主要差異化特點
- Fine digital delay adjustment (對比SY89296UTI-TR)
- Combined coarse and continuous tuning (對比SY89296UTI-TR)
- High-speed differential timing control (對比SY89296UTI-TR)
設計說明
Place the SY89296UTI close to the circuit whose timing must be adjusted, because additional trace length introduces delay and jitter that the calibration process cannot distinguish from the programmed delay. Route the differential input and output signals as a matched pair over a continuous reference plane. Avoid stubs and unnecessary test-point structures on high-speed LVPECL nets, and confirm the final layer stack against the manufacturer layout guidance.
Use the digital control word for repeatable coarse adjustment and reserve analog fine tuning for calibration of approximately 40 ps. Record both settings because a small analog-control change can alter the final edge position. Validate setup time, hold time, jitter, and eye margin at the receiving circuit rather than assuming that a nominal 10 ps control increment is the only timing contribution. Differential LVPECL paths require continuous return paths and controlled impedance.
Decouple the 2.5 V or 3.3 V supply close to the device and follow the manufacturer’s recommended capacitor values and placement. The SY89296UTI supports high-speed differential signaling, so supply-noise coupling can affect the delayed output even when the digital delay setting is correct. Keep power and ground connections short, provide a low-impedance return path, and verify the design for both operating supply conditions and the required temperature range.
Do not treat the SY89296UTI and SY89296UTI-TR ordering expressions as interchangeable without checking the package drawing, tape dimensions, reel orientation, and dry-packing requirements. Also avoid assuming that a generic programmable delay line is a drop-in replacement: the control protocol, 1,024-tap range, 10 ps increment, D[10] cascade function, analog fine-tune control, and LVPECL pinout must all match the target PCB.
合規資訊
Compliance attributes were not explicitly identified for the exact SY89296UTI ordering configuration. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status with Microchip Technology before production release.