SY89808LTI - 500MHz 1:9 Differential HSTL Buffer | Microchip
MPN: SY89808LTI ✓ 啟用中SY89808LTI 概覽
A differential fanout buffer is a clock-and-timing semiconductor that preserves a differential clock or data signal while distributing it to multiple destinations. Its role in the hierarchy is clock buffer → fanout buffer → clock and timing IC → semiconductor. HSTL is a low-swing, source-terminated signaling method commonly used for high-speed digital interconnects. Translating and buffering the signal at the distribution point helps drive multiple loads without loading the original source.
The SY89808LTI’s principal specifications are its 500 MHz operating frequency, 1:9 fanout ratio, 3.3 V supply voltage, differential input and output architecture, and 1.5 V HSTL signal level. These characteristics make the device applicable where one high-speed differential source must reach multiple downstream circuits while maintaining a consistent voltage interface. The 1:9 ratio allows a single input branch to feed nine output branches without requiring nine separate source buffers.
The differential architecture is particularly useful when signal integrity depends on matched edge timing through a multi-drop board topology. A common source can drive the buffer input, while the nine outputs provide local distribution points for receivers, controllers, memory interfaces, or downstream clock-generating circuits. Because skew and return-loss performance depend on PCB topology, trace length matching, termination, and reference-plane continuity, the implementation around the device is as important as the stated operating frequency.
Typical uses include high-speed parallel-processing systems, networking and communications equipment, test and measurement systems, data-conversion platforms, and clock distribution around FPGAs or other digital controllers. A single high-speed differential clock can be distributed to multiple parallel destinations, while the translator function supports interfacing between 1.5 V HSTL logic and circuitry operating from a 3.3 V supply.
For a new layout, place the device so that input and output differential pairs have matched impedances and controlled length. Follow the manufacturer’s pin-description and layout guidance when assigning termination and decoupling. Avoid introducing long stubs between the outputs and their receivers because stubs can create reflections that reduce the usable bandwidth below the 500 MHz device capability.
This product page consolidates the verified SY89808LTI function, package, interface, and sourcing information with practical clock-distribution guidance. It also identifies where detailed electrical, pin-level, environmental, and lifecycle information must be confirmed in the manufacturer datasheet before a production design is released.
直接替換替代品,適用於 SY89808LTI — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
SY89808LTG
✅ 直接替換聯絡詢價
查看資料表 →SY89808LTI 規格
| Product Type | Differential HSTL fanout buffer/translator |
| 供應電壓 | 3.3 V |
| Maximum Operating Frequency | 500 MHz |
| Fanout Ratio | 1:9 |
| Signal Interface | Differential HSTL |
| HSTL Signal Voltage | 1.5 V |
| 輸出數量 | 9 differential outputs |
| Input Configuration | 1 differential input |
| Logic Family | HSTL |
| 封裝 | 32-pin TQFP |
| 安裝類型 | Surface mount |
SY89808LTI 32-pin tqfp 腳位配置指南
SY89808LTI(32-pin tqfp 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: SY89808LTI.
請參閱 資料表 以查看完整腳位配置。
典型應用
SY89808LTI 適用於 6 應用s: High-Speed Clock Distribution, FPGA Parallel-Interface Support, Communications Equipment, Parallel Data Distribution, Test and Measurement Systems, Data-Conversion Platforms.
High-Speed Clock Distribution
The SY89808LTI fits a single-source, nine-destination clock tree because its 1:9 differential HSTL fanout ratio can distribute one clock to nine branches at up to 500 MHz. Place the source at the input and route each differential output as a controlled-impedance pair to its assigned receiver. The 3.3 V supply and 1.5 V HSTL interface support low-swing distribution, while matched trace geometry and source termination help limit timing degradation.
推薦
FPGA Parallel-Interface Support
The SY89808LTI can distribute a 500 MHz differential clock across nine parallel FPGA or controller domains. Its one-input, nine-output differential arrangement avoids combining multiple long loads directly at the clock source and gives each branch a defined fanout point. The HSTL interface operates at 1.5 V from a 3.3 V supply. Board implementation should preserve pair symmetry, provide continuous reference planes, and avoid stubs that could reflect clock energy.
推薦
Communications Equipment
The SY89808LTI is applicable in communications equipment that requires a high-speed differential source to reach multiple timing domains. Its 500 MHz capability and 1:9 fanout ratio suit central clock distribution in line cards, interface modules, and backplane-related logic. The 3.3 V-powered, 1.5 V HSTL interface provides a defined signaling method, while proper source termination and impedance-controlled routing are essential to preserve edge quality across the board.
推薦
Parallel Data Distribution
The SY89808LTI can translate and fan out a differential HSTL signal when multiple high-speed data paths require synchronized distribution. Its 1:9 architecture gives designers a practical way to separate nine destinations from one source, while the 500 MHz rating addresses demanding parallel interfaces. Because timing margin depends on skew and edge degradation, route each output as a matched pair and verify the complete channel against receiver thresholds and termination requirements.
推薦
Test and Measurement Systems
The SY89808LTI is suited to clock distribution in test and measurement equipment where a common differential stimulus must reach multiple acquisition, capture, or processing paths. The 1:9 fanout ratio supports branched clock trees at up to 500 MHz, and the translator function provides a 1.5 V HSTL interface from a 3.3 V supply. Layout should minimize branch length differences and connector-related discontinuities so channel-to-channel timing remains predictable.
推薦
Data-Conversion Platforms
The SY89808LTI can provide a common differential clock to multiple converters and digital processing blocks in a high-speed data-acquisition platform. Its nine differential outputs simplify fanout architecture, while the 3.3 V supply and 1.5 V HSTL level suit systems with compact high-speed interfaces. The device should be positioned centrally enough to limit trace lengths, and each pair requires matched geometry, suitable return paths, and termination selected from the manufacturer’s reference design.
推薦
推薦產品摘要
工程參考資料,適用於 SY89808LTI — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | SY89808LTG |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 32-pin TQFP | 32-pin TQFP |
| Product Type | Differential HSTL fanout buffer/translator | Differential HSTL fanout buffer/translator |
| Operating Frequency | 500 MHz | 500 MHz |
| Signal Interface | Differential HSTL | Differential HSTL |
主要差異化特點
- One-to-nine differential fanout in a single device (對比SY89808LTG)
- Integrated HSTL translation and clock distribution (對比SY89808LTG)
- High-speed differential distribution (對比SY89808LTG)
設計說明
Route every differential pair with matched geometry, continuous reference planes, and the impedance specified by the manufacturer’s interface guidance. Keep the input pair and each output pair as short as practical, maintain consistent spacing between pair members, and avoid vias that unnecessarily disrupt return paths. At the 500 MHz capability of the SY89808LTI, trace discontinuities and reference-plane changes can degrade edge quality even when the nominal clock frequency is correct.
Use the manufacturer’s recommended HSTL source-termination and output configuration instead of applying generic low-voltage termination by analogy. Termination values depend on trace impedance, receiver topology, source resistance, and whether outputs are lightly loaded. Keep output stubs exceptionally short because a capacitive stub can act as a discontinuity and reflect energy back into the buffer, reducing rise time and potentially causing double-edge or ringing behavior.
Do not treat the 1:9 fanout rating as permission to create nine arbitrary long branches. Match branch topology where channel-to-channel timing matters, preserve differential symmetry, and verify source, output, and receiver loading in simulation. The SY89808LTI is a clock-and-timing distribution device, not a general-purpose logic buffer, and its HSTL interface requires deliberate termination and routing.
合規資訊
Compliance attributes are not stated in the available product and distributor records. Confirm RoHS, REACH, automotive qualification, lead-free, halogen-free, and conflict-minerals status using the manufacturer’s current product documentation or declarations.