THS3110ID - 100MHz Current-Feedback Op Amp | Texas Instruments
MPN: THS3110ID ✓ 啟用中THS3110ID 概覽
A current-feedback amplifier is a voltage-feedback amplifier alternative optimized for high-speed, wide-gain-bandwidth operation. Unlike a conventional voltage-feedback operational amplifier, its bandwidth and distortion behavior remain more nearly constant across a range of closed-loop gains. This makes the THS3110ID useful in instrumentation, communications, video, and data-acquisition systems where low noise, fast slew rate, and strong output-drive capability are required within the broader amplifier IC and analog-signal-processing hierarchy.
The principal specifications include 2 pA/√Hz noninverting current noise, 10 pA/√Hz inverting current noise, and 3 nV/√Hz voltage noise. The amplifier also provides a wide output-current drive of 260 mA and a slew rate of 1300 V/µs when driving an 8 V peak-to-peak load. The power-down pin places the device in a low-power standby state, while the 100 MHz bandwidth supports good distortion performance below 10 MHz, as described by Texas Instruments.
The THS3110 uses current-feedback topology rather than the conventional voltage-feedback architecture. This topology permits wide closed-loop gain ranges without the same bandwidth collapse commonly associated with voltage-feedback amplifiers. The combination of high-speed operation and low noise is especially useful for buffering wideband transducers and processing high-frequency analog signals, although board layout, load stability, and feedback-component selection remain critical to realized performance.
Typical applications include precision instrumentation, ultrasound and medical signal chains, communications equipment, video processing, professional audio, and high-speed data-acquisition systems. The ±5 V to ±15 V supply range supports bipolar analog systems, while the 260 mA output-current capability is useful for driving moderate loads and cable capacitance. The power-down feature can also reduce system consumption when the signal path is not active.
When laying out a THS3110ID circuit, use short feedback paths, maintain symmetry around the amplifier, place compensation and feedback components close to their associated pins, and avoid long traces between the amplifier and its external networks. Designers should verify stability with the intended load, gain, supply decoupling, and output termination rather than relying only on nominal bandwidth figures.
This product page consolidates the manufacturer's electrical characteristics, package information, power-down behavior, application guidance, and qualified drop-in alternatives. It also provides engineering-focused comparisons and design notes to help select, lay out, and validate a current-feedback amplifier in high-speed analog systems.
直接替換替代品,適用於 THS3110ID — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: THS3110ID (相同外形與佔位) — 差異在於 Amplifier Type, Inverting Current Noise, Noninverting Current Noise, Slew Rate, Supply Voltage Range.
THS3111ID
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →THS3110IDR
✅ 直接替換📋 參考替代品(不在目錄中)
THS3110IDG4
✅ 直接替換📋 參考替代品(不在目錄中)
THS3110IDRG4
✅ 直接替換📋 參考替代品(不在目錄中)
THS3110ID 最大額定值與電氣特性
| Amplifier Type | Current-feedback operational amplifier |
| Number of Channels | 1 channel |
| Unity-Gain Bandwidth | 100 MHz |
| Wide Bandwidth | 90 MHz |
| Slew Rate | 1300 V/µs at RL = 8 Vpp |
| Noninverting Current Noise | 2 pA/√Hz |
| Inverting Current Noise | 10 pA/√Hz |
| Voltage Noise | 3 nV/√Hz |
| Output Current Drive | 260 mA |
| Supply Voltage Range | ±5 V to ±15 V |
| Maximum Total Supply Voltage | 30 V |
| Active Quiescent Current | 4.8 mA |
| Power-Down Quiescent Current | 270 µA |
| 工作溫度範圍 | -40°C to +85°C |
| 封裝 | 8-pin SOIC (D) |
| Package Width | 3.90 mm |
| 安裝類型 | Surface mount |
| Power-Down Control | Dedicated power-down pin |
THS3110ID 3.90 mm 腳位配置指南
THS3110ID(3.90 mm 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: THS3110ID.
請參閱 資料表 以查看完整腳位配置。
典型應用
THS3110ID 適用於 6 應用s: Precision Instrumentation Signal Conditioning, High-Speed Data Acquisition, Communications Receiver Front End, Professional Audio Signal Path, Video Processing Amplifier, Portable Diagnostic and Monitoring Equipment.
Precision Instrumentation Signal Conditioning
The THS3110ID fits precision instrumentation front ends that must amplify sensor or measurement signals without adding excessive noise. Its 3 nV/√Hz voltage noise, 2 pA/√Hz noninverting current noise, and 10 pA/√Hz inverting current noise support low-level signal capture, while 100 MHz unity-gain bandwidth provides substantial operating headroom. Place the amplifier near the source and use the manufacturer-recommended feedback network to preserve bandwidth and stability. The 260 mA output-current capability also helps drive moderate loading, although long sensor cables and high-capacitance inputs require careful isolation and layout.
推薦
High-Speed Data Acquisition
The THS3110ID is suitable for high-speed data-acquisition channels requiring fast slew rate and low input noise. Its 1300 V/µs slew rate allows large output transitions to occur quickly, while the 100 MHz unity-gain bandwidth supports signal paths operating below 10 MHz with good distortion characteristics. The current-feedback architecture is useful when multiple closed-loop gains must be accommodated without relying on a voltage-feedback amplifier with sharply reduced bandwidth. Use short signal paths, symmetric feedback routing, and local supply bypass capacitors to preserve stability and control parasitic feedback.
推薦
Communications Receiver Front End
The THS3110ID can serve as a wideband receive-path amplifier in communications equipment operating from bipolar supplies. Its 100 MHz unity-gain bandwidth, low voltage noise, and 260 mA output-current drive provide a useful combination for intermediate-frequency or wideband analog stages. The ±5 V to ±15 V supply range accommodates established bipolar system architectures. Designers should control impedance at both inputs, use recommended feedback values, and verify gain flatness and peaking with the actual mixer, filter, and cable loading because current-feedback amplifiers are sensitive to feedback impedance and source impedance.
推薦
Professional Audio Signal Path
The THS3110ID is appropriate for professional audio and low-noise analog processing stages requiring fast transient response and strong output drive. Its 260 mA output-current capability is useful for driving moderate loads, while the 100 MHz bandwidth and 1300 V/µs slew rate support low-distortion high-frequency behavior below 10 MHz. The power-down pin reduces quiescent current from 4.8 mA to 270 µA during standby, benefiting multichannel equipment with intermittent operation. Keep the feedback loop short, maintain symmetrical grounding, and verify the output swing against the selected ±5 V to ±15 V supply arrangement.
推薦
Video Processing Amplifier
The THS3110ID can support video and general high-speed analog-processing stages where fast large-signal response and broad bandwidth are required. Its 1300 V/µs slew rate and 100 MHz unity-gain bandwidth provide adequate margin for signals below 10 MHz, while the current-feedback topology maintains performance across changing closed-loop gains more effectively than many voltage-feedback choices. High-speed video paths should be routed over controlled-impedance traces with a continuous ground reference. The designer should also check DC gain accuracy, output range, and stability with the intended cable or ADC input capacitance.
推薦
Portable Diagnostic and Monitoring Equipment
The THS3110ID fits diagnostic and monitoring equipment that alternates between active measurement and low-power standby operation. Its active quiescent current is 4.8 mA, while the dedicated power-down mode lowers this to 270 µA, reducing consumption when a channel is inactive. The low-noise characteristics help preserve weak sensor signals, and the 100 MHz bandwidth allows the same amplifier to handle demanding stimulus or measurement edges. Use the power-down control only after confirming its logic polarity and output behavior, and design the shutdown sequence so downstream converters and ADC inputs remain in safe states.
推薦
推薦產品摘要
工程參考資料,適用於 THS3110ID — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | THS3111ID | THS3110IDR | THS3110IDG4 | THS3110IDRG4 |
|---|---|---|---|---|---|
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Type | Current-feedback amplifier | Current-feedback amplifier | Current-feedback amplifier | Current-feedback amplifier | Current-feedback amplifier |
| Number of Channels | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel |
| Supply Voltage Range | ±5 V to ±15 V | ±5 V to ±15 V family range | ±5 V to ±15 V | ±5 V to ±15 V | ±5 V to ±15 V |
主要差異化特點
- High-speed current-feedback performance in a single amplifier (對比THS3111ID)
- Strong output-current capability (對比THS3110IDR)
- Low-power standby capability (對比THS3110IDG4)
- Low-noise high-speed signal handling (對比THS3110IDRG4)
設計說明
Keep the THS3110ID feedback loop physically small and route the feedback trace away from input, output, and power paths. Place feedback resistors close to the amplifier, use symmetrical connections around the device, and avoid adding capacitance at the inverting input. With a 1300 V/µs slew rate and 260 mA output drive, long or asymmetric routing can create ringing or unstable feedback behavior even when the schematic follows the recommended topology.
Follow the manufacturer’s supply-decoupling network and place bypass capacitors directly beside the corresponding THS3110ID power pins. The amplifier supports ±5 V to ±15 V operation, but high-speed switching current circulates through the supply loops. Use a low-impedance ground plane and keep the positive and negative return paths short. Validate the design at the intended gain because current-feedback amplifiers can require different feedback impedances at different operating modes.
Do not assume that any current-feedback amplifier with the same SOIC-8 footprint is automatically interchangeable. Confirm the complete pin description, supply limits, power-down polarity, gain-setting network, and recommended feedback resistors before substituting THS3111ID. Also verify common-mode range and output swing at the selected supply voltage. A footprint match alone does not guarantee signal compatibility or stability.
Estimated: at ±15 V with 4.8 mA quiescent current and an output near 0 V, internal power dissipation is approximately 144 mW before output-current contribution. Estimated: at ±15 V with a 20 mA output current into a 5 V load, the approximate supply-input contribution is 600 mW, producing about 300 mW output load power. Actual dissipation depends on operating class, supply arrangement, and ambient temperature; confirm the result against the manufacturer’s power-dissipation and thermal information for the SOIC-8 package.
合規資訊
The THS3110ID is a commercial operational amplifier rather than an automotive-qualified AEC-Q100 device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established by the cited sources and remain unknown.