Texas Instruments

THS3110ID - 100MHz Current-Feedback Op Amp | Texas Instruments

N.º de pieza: THS3110ID ✓ Activo
3 nV/√Hz Vdss 2 pA/√Hz Id 8-pin SOIC (D) Package
MOQ: 1 |

THS3110ID Descripción general

The Texas Instruments THS3110ID is a single, low-noise current-feedback operational amplifier with a 100 MHz unity-gain bandwidth, 1300 V/µs slew rate, and 260 mA output-current drive capability. Designed for high-voltage precision signal chains, the device operates from ±5 V to ±15 V and is offered in an 8-pin SOIC (D) package. Its power-down function reduces quiescent current from 4.8 mA to 270 µA.

A current-feedback amplifier is a voltage-feedback amplifier alternative optimized for high-speed, wide-gain-bandwidth operation. Unlike a conventional voltage-feedback operational amplifier, its bandwidth and distortion behavior remain more nearly constant across a range of closed-loop gains. This makes the THS3110ID useful in instrumentation, communications, video, and data-acquisition systems where low noise, fast slew rate, and strong output-drive capability are required within the broader amplifier IC and analog-signal-processing hierarchy.

The principal specifications include 2 pA/√Hz noninverting current noise, 10 pA/√Hz inverting current noise, and 3 nV/√Hz voltage noise. The amplifier also provides a wide output-current drive of 260 mA and a slew rate of 1300 V/µs when driving an 8 V peak-to-peak load. The power-down pin places the device in a low-power standby state, while the 100 MHz bandwidth supports good distortion performance below 10 MHz, as described by Texas Instruments.

The THS3110 uses current-feedback topology rather than the conventional voltage-feedback architecture. This topology permits wide closed-loop gain ranges without the same bandwidth collapse commonly associated with voltage-feedback amplifiers. The combination of high-speed operation and low noise is especially useful for buffering wideband transducers and processing high-frequency analog signals, although board layout, load stability, and feedback-component selection remain critical to realized performance.

Typical applications include precision instrumentation, ultrasound and medical signal chains, communications equipment, video processing, professional audio, and high-speed data-acquisition systems. The ±5 V to ±15 V supply range supports bipolar analog systems, while the 260 mA output-current capability is useful for driving moderate loads and cable capacitance. The power-down feature can also reduce system consumption when the signal path is not active.

When laying out a THS3110ID circuit, use short feedback paths, maintain symmetry around the amplifier, place compensation and feedback components close to their associated pins, and avoid long traces between the amplifier and its external networks. Designers should verify stability with the intended load, gain, supply decoupling, and output termination rather than relying only on nominal bandwidth figures.

This product page consolidates the manufacturer's electrical characteristics, package information, power-down behavior, application guidance, and qualified drop-in alternatives. It also provides engineering-focused comparisons and design notes to help select, lay out, and validate a current-feedback amplifier in high-speed analog systems.

Alternativas directas para THS3110ID — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con THS3110ID (mismo factor de forma y huella) — difiere en Amplifier Type, Inverting Current Noise, Noninverting Current Noise, Slew Rate, Supply Voltage Range.

Texas Instruments
Amplifier Type: Current-Feedback Amplifier
Inverting Current Noise: 10 pA/sqrt(Hz)
Noninverting Current Noise: 2 pA/sqrt(Hz)
Comparar con THS3110ID →

THS3111ID

✅ Sustitución directa ⚠️ Especificaciones sin verificar
Texas Instruments
📦 8-pin SOIC (D)
Current-Feedback Amplifier · 1 channel · +/-5 V to +/-15 V · 90 MHz · 1300 V/us at RL = 8 VPP · 2 pA/sqrt(Hz) · 10 pA/sqrt(Hz) · 3 nV/sqrt(Hz)

Consulte el precio

Ver hoja de datos →

THS3110IDR

✅ Sustitución directa
📦 8-pin SOIC (D)
Same THS3110 electrical device and 8-pin SOIC footprint; reel-oriented orderable suffix changes shipping format rather than core parameters

📋 Alternativa de referencia (no en el catálogo)

THS3110IDG4

✅ Sustitución directa
📦 8-pin SOIC (D)
Same THS3110 electrical device and 8-pin SOIC footprint; orderable suffix changes device handling rather than the specified core electrical ratings

📋 Alternativa de referencia (no en el catálogo)

THS3110IDRG4

✅ Sustitución directa
📦 8-pin SOIC (D)
Same THS3110 electrical device and 8-pin SOIC footprint; combined reel and orderable suffix changes packaging metadata rather than core specifications

📋 Alternativa de referencia (no en el catálogo)

THS3110ID Valores máximos y características eléctricas

Amplifier Type Current-feedback operational amplifier
Number of Channels 1 channel
Unity-Gain Bandwidth 100 MHz
Wide Bandwidth 90 MHz
Slew Rate 1300 V/µs at RL = 8 Vpp
Noninverting Current Noise 2 pA/√Hz
Inverting Current Noise 10 pA/√Hz
Voltage Noise 3 nV/√Hz
Output Current Drive 260 mA
Supply Voltage Range ±5 V to ±15 V
Maximum Total Supply Voltage 30 V
Active Quiescent Current 4.8 mA
Power-Down Quiescent Current 270 µA
Rango de temperatura de funcionamiento -40°C to +85°C
Encapsulado 8-pin SOIC (D)
Package Width 3.90 mm
Tipo de montaje Surface mount
Power-Down Control Dedicated power-down pin

Guía de configuración de pines de THS3110ID 3.90 mm

Configuración de pines para THS3110ID (encapsulado 3.90 mm). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.

Diagrama de patillaje del encapsulado 3.90 mm para THS3110ID

No hay datos detallados de patillaje disponibles para THS3110ID.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

THS3110ID es adecuado para 6 aplicacións: Precision Instrumentation Signal Conditioning, High-Speed Data Acquisition, Communications Receiver Front End, Professional Audio Signal Path, Video Processing Amplifier, Portable Diagnostic and Monitoring Equipment.

🏭

Precision Instrumentation Signal Conditioning

The THS3110ID fits precision instrumentation front ends that must amplify sensor or measurement signals without adding excessive noise. Its 3 nV/√Hz voltage noise, 2 pA/√Hz noninverting current noise, and 10 pA/√Hz inverting current noise support low-level signal capture, while 100 MHz unity-gain bandwidth provides substantial operating headroom. Place the amplifier near the source and use the manufacturer-recommended feedback network to preserve bandwidth and stability. The 260 mA output-current capability also helps drive moderate loading, although long sensor cables and high-capacitance inputs require careful isolation and layout.

🖥️

High-Speed Data Acquisition

The THS3110ID is suitable for high-speed data-acquisition channels requiring fast slew rate and low input noise. Its 1300 V/µs slew rate allows large output transitions to occur quickly, while the 100 MHz unity-gain bandwidth supports signal paths operating below 10 MHz with good distortion characteristics. The current-feedback architecture is useful when multiple closed-loop gains must be accommodated without relying on a voltage-feedback amplifier with sharply reduced bandwidth. Use short signal paths, symmetric feedback routing, and local supply bypass capacitors to preserve stability and control parasitic feedback.

🌐

Communications Receiver Front End

The THS3110ID can serve as a wideband receive-path amplifier in communications equipment operating from bipolar supplies. Its 100 MHz unity-gain bandwidth, low voltage noise, and 260 mA output-current drive provide a useful combination for intermediate-frequency or wideband analog stages. The ±5 V to ±15 V supply range accommodates established bipolar system architectures. Designers should control impedance at both inputs, use recommended feedback values, and verify gain flatness and peaking with the actual mixer, filter, and cable loading because current-feedback amplifiers are sensitive to feedback impedance and source impedance.

🎧

Professional Audio Signal Path

The THS3110ID is appropriate for professional audio and low-noise analog processing stages requiring fast transient response and strong output drive. Its 260 mA output-current capability is useful for driving moderate loads, while the 100 MHz bandwidth and 1300 V/µs slew rate support low-distortion high-frequency behavior below 10 MHz. The power-down pin reduces quiescent current from 4.8 mA to 270 µA during standby, benefiting multichannel equipment with intermittent operation. Keep the feedback loop short, maintain symmetrical grounding, and verify the output swing against the selected ±5 V to ±15 V supply arrangement.

📺

Video Processing Amplifier

The THS3110ID can support video and general high-speed analog-processing stages where fast large-signal response and broad bandwidth are required. Its 1300 V/µs slew rate and 100 MHz unity-gain bandwidth provide adequate margin for signals below 10 MHz, while the current-feedback topology maintains performance across changing closed-loop gains more effectively than many voltage-feedback choices. High-speed video paths should be routed over controlled-impedance traces with a continuous ground reference. The designer should also check DC gain accuracy, output range, and stability with the intended cable or ADC input capacitance.

💊

Portable Diagnostic and Monitoring Equipment

The THS3110ID fits diagnostic and monitoring equipment that alternates between active measurement and low-power standby operation. Its active quiescent current is 4.8 mA, while the dedicated power-down mode lowers this to 270 µA, reducing consumption when a channel is inactive. The low-noise characteristics help preserve weak sensor signals, and the 100 MHz bandwidth allows the same amplifier to handle demanding stimulus or measurement edges. Use the power-down control only after confirming its logic polarity and output behavior, and design the shutdown sequence so downstream converters and ADC inputs remain in safe states.

What are the key specifications of THS3110ID that engineers should know?
The THS3110ID is a single current-feedback amplifier with 100 MHz unity-gain bandwidth, 1300 V/µs slew rate, and 260 mA output-current drive. Texas Instruments specifies 3 nV/√Hz voltage noise, 2 pA/√Hz noninverting current noise, and 10 pA/√Hz inverting current noise. The device operates from ±5 V to ±15 V, includes a power-down pin, and is packaged in 8-pin SOIC (D). Its current-feedback architecture is particularly useful in wideband instrumentation, communications, video, and audio signal chains where fast settling and strong load drive are important.
Where can I download the THS3110ID datasheet PDF?
The THS3110ID datasheet can be obtained from the linked Texas Instruments product page or the manufacturer-linked PDF at DigChip. The manufacturer describes the device as a single, low-noise, high-voltage current-feedback amplifier with power-down. The document covers the ±5 V to ±15 V supply range, 100 MHz unity-gain bandwidth, 1300 V/µs slew rate, and detailed applications for instrumentation, communications, and video systems. Always compare the package marking and complete orderable MPN before using the document for a production design.
What is the supply voltage range of the THS3110ID?
The THS3110ID operates from ±5 V to ±15 V, corresponding to a total supply voltage from 10 V to 30 V. Texas Instruments describes the amplifier as a high-voltage current-feedback device intended for bipolar analog systems. Because it is not a rail-to-rail input or output amplifier, engineers must confirm that the input signal and required output swing remain within the specified common-mode and output-voltage limits for the selected supply voltage. The complete absolute-maximum and electrical-characteristic tables should govern the final design.
How much bandwidth does THS3110ID provide?
The THS3110ID provides 100 MHz unity-gain bandwidth and is also described as having 90 MHz wide bandwidth. According to the Texas Instruments product information, the 100 MHz unity-gain bandwidth supports good distortion characteristics below 10 MHz. Because this is a current-feedback amplifier, its closed-loop response and stability must be evaluated at the intended gain rather than treated exactly like a conventional voltage-feedback amplifier. Feedback resistor values, load capacitance, and output termination materially affect the realized bandwidth and peaking.
What noise performance does THS3110ID provide?
The THS3110ID offers 2 pA/√Hz noninverting current noise, 10 pA/√Hz inverting current noise, and 3 nV/√Hz voltage noise. These figures make the amplifier suitable for low-noise high-speed signal chains, including instrumentation and communications equipment. Current noise is especially important when the source impedance and feedback network create meaningful thermal-current noise, while voltage noise dominates low-source-impedance measurements. System noise should be evaluated with the actual source impedance, feedback resistors, gain setting, and measurement bandwidth.
What can replace THS3110ID without changing the PCB footprint?
The closest identified footprint-compatible choices are THS3111ID and orderable THS3110ID suffix variants using the same 8-pin SOIC package. THS3111ID is a member of the same TI current-feedback family and is the principal family-level replacement candidate. The suffix variants differ primarily in shipping or orderable-device coding, so they add little functional differentiation. Verify the complete orderable MPN, marking, supply limits, enable logic, and electrical characteristics before approving any replacement for production.
Is THS3110ID the same as THS3111ID?
THS3110ID and THS3111ID belong to the same Texas Instruments high-voltage, low-noise current-feedback amplifier family and share the principal supply-voltage and packaging families. They should not be treated as automatically identical devices, however, because pin functions, bandwidth, stability, or power-control behavior may differ between family members. The manufacturer lists SOIC-8 and MSOP-8 options for the THS3110 and THS3111 family. Confirm the exact THS3111 package suffix and compare its pin description against the THS3110ID before treating it as a drop-in replacement.
When should I choose THS3110ID instead of another current-feedback amplifier?
Choose the THS3110ID when the design needs a single, low-noise current-feedback amplifier with 100 MHz unity-gain bandwidth, 1300 V/µs slew rate, and 260 mA output drive in an 8-pin SOIC. It is particularly attractive for bipolar analog systems using ±5 V to ±15 V supplies and for channels requiring a dedicated power-down function. Select another amplifier when its input common-mode range, output swing, stability network, supply arrangement, or package offers a clearer advantage.
Is THS3110ID suitable for high-speed instrumentation?
Yes, the THS3110ID is suitable for high-speed instrumentation because it combines 100 MHz unity-gain bandwidth, low voltage noise, and strong output-current drive. Its current-feedback topology is useful when the required gain range would narrow the bandwidth of many voltage-feedback amplifiers. For practical use, evaluate the complete source impedance, feedback network, load, and cable capacitance. Stable high-frequency operation depends on short PCB traces, correct feedback resistors, adequate supply bypassing, and control of output loading.
What is the benefit of the THS3110ID power-down function?
The THS3110ID power-down function reduces quiescent current from 4.8 mA to 270 µA while the amplifier is in standby. This can conserve power in multichannel, portable, or intermittently operated analog systems. The control pin allows the signal path to be disabled without removing the main supply. Designers should still define the logic levels, ensure the output reaches a safe state during shutdown, and verify that the mode meets the application’s settling and power-consumption requirements.
How should feedback resistors be selected for THS3110ID?
Use the feedback-resistor values and gain-setting network specified in the Texas Instruments THS3110 datasheet for the intended operating mode. Current-feedback amplifiers are sensitive to feedback impedance because the inverting input works through a virtual ground whose magnitude depends on the feedback network. Changing the feedback resistor can alter bandwidth, gain accuracy, noise, and peaking even when the closed-loop gain remains constant. Use the manufacturer’s recommended values where possible, then validate stability across gain, load, supply, and temperature.
How should the THS3110ID PCB layout be optimized?
Place the THS3110ID close to its feedback resistors and decoupling capacitors, and keep the feedback loop physically small. Route input, output, and feedback paths with short traces and minimize parasitic capacitance at the inverting input. Place each supply bypass capacitor directly beside its corresponding power pin and follow the decoupling network in the manufacturer datasheet. Ground-return paths should be short and symmetric. With 1300 V/µs slew rate and 260 mA drive capability, careful layout is essential for controlling ringing and maintaining stability.
What is the power dissipation concern for THS3110ID?
THS3110ID power dissipation depends on the total supply voltage, quiescent current, output voltage, and load current rather than on supply voltage alone. For example, Estimated: at ±15 V, a 4.8 mA quiescent current and approximately 0 V output imply about 144 mW internal dissipation before accounting for output-current contribution. Actual dissipation also includes the output stage’s voltage and current multiplication. Use the manufacturer’s thermal and absolute-maximum information to evaluate junction temperature and the 8-pin SOIC copper area.
Where can I buy THS3110ID and check its current lead time?
Use the Request a Quote form on this page to request current THS3110ID availability, lead time, order quantity, and shipment options. Texas Instruments offers the THS3110ID in an 8-pin SOIC package, while distributor inventory and lead times can change independently of the manufacturer’s lifecycle status. The product is described as active on the manufacturer’s part-details page. Submit the required MPN and target quantity so the current commercial response can be matched to the intended assembly schedule.
How does THS3110ID compare with THS3111ID for a drop-in replacement?
THS3111ID is the closest same-family candidate for a drop-in evaluation because Texas Instruments presents THS3110 and THS3111 together as low-noise, high-voltage current-feedback amplifiers. Both families are offered in SOIC-8 and MSOP-8 configurations, but that package similarity alone does not prove pin compatibility. Before replacing THS3110ID, compare the complete pin descriptions, supply range, bandwidth, output-drive specification, power-down polarity, recommended feedback resistors, and absolute-maximum ratings. Use the exact package suffix on the approved purchase order.
What is the best Texas Instruments equivalent for THS3110ID?
The best identified Texas Instruments family candidate is THS3111ID because it belongs to the same low-noise, high-voltage current-feedback amplifier family and is available in an 8-pin SOIC configuration. It should still be treated as a qualified replacement rather than an automatic substitution. Compare the THS3111ID pinout and AC/DC specifications against the THS3110ID in the manufacturer documentation. Orderable THS3110ID suffix variants also share the footprint, but they provide less engineering differentiation than a distinct family member.

Datos de referencia de ingeniería para THS3110ID — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose THS3110ID for a high-speed, low-noise current-feedback amplifier that needs 100 MHz unity-gain bandwidth, 1300 V/µs slew rate, 260 mA output drive, and a dedicated power-down function in an 8-pin SOIC. Consider THS3111ID when its pin functions, bandwidth, and power-control behavior better match the circuit, but validate it as a family replacement rather than assuming exact equivalence. THS3110IDR, THS3110IDG4, and THS3110IDRG4 are orderable-suffix options for the same core device and are useful when packaging or order processing requires a specific suffix. For designs requiring rail-to-rail inputs, a different bandwidth range, lower noise, or a different power architecture, select an amplifier whose complete electrical specification aligns with those needs rather than relying on package similarity.

Comparación con alternativas

Parámetro Este producto THS3111ID THS3110IDR THS3110IDG4 THS3110IDRG4
Package 8-pin SOIC (D) 8-pin SOIC (D) 8-pin SOIC (D) 8-pin SOIC (D) 8-pin SOIC (D)
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Amplifier Type Current-feedback amplifier Current-feedback amplifier Current-feedback amplifier Current-feedback amplifier Current-feedback amplifier
Number of Channels 1 channel 1 channel 1 channel 1 channel 1 channel
Supply Voltage Range ±5 V to ±15 V ±5 V to ±15 V family range ±5 V to ±15 V ±5 V to ±15 V ±5 V to ±15 V

Diferenciadores clave

  • High-speed current-feedback performance in a single amplifier (frente a THS3111ID)
  • Strong output-current capability (frente a THS3110IDR)
  • Low-power standby capability (frente a THS3110IDG4)
  • Low-noise high-speed signal handling (frente a THS3110IDRG4)

Notas de diseño

Keep the THS3110ID feedback loop physically small and route the feedback trace away from input, output, and power paths. Place feedback resistors close to the amplifier, use symmetrical connections around the device, and avoid adding capacitance at the inverting input. With a 1300 V/µs slew rate and 260 mA output drive, long or asymmetric routing can create ringing or unstable feedback behavior even when the schematic follows the recommended topology.

Follow the manufacturer’s supply-decoupling network and place bypass capacitors directly beside the corresponding THS3110ID power pins. The amplifier supports ±5 V to ±15 V operation, but high-speed switching current circulates through the supply loops. Use a low-impedance ground plane and keep the positive and negative return paths short. Validate the design at the intended gain because current-feedback amplifiers can require different feedback impedances at different operating modes.

Do not assume that any current-feedback amplifier with the same SOIC-8 footprint is automatically interchangeable. Confirm the complete pin description, supply limits, power-down polarity, gain-setting network, and recommended feedback resistors before substituting THS3111ID. Also verify common-mode range and output swing at the selected supply voltage. A footprint match alone does not guarantee signal compatibility or stability.

Estimated: at ±15 V with 4.8 mA quiescent current and an output near 0 V, internal power dissipation is approximately 144 mW before output-current contribution. Estimated: at ±15 V with a 20 mA output current into a 5 V load, the approximate supply-input contribution is 600 mW, producing about 300 mW output load power. Actual dissipation depends on operating class, supply arrangement, and ambient temperature; confirm the result against the manufacturer’s power-dissipation and thermal information for the SOIC-8 package.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The THS3110ID is a commercial operational amplifier rather than an automotive-qualified AEC-Q100 device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established by the cited sources and remain unknown.

Datos verificados el: 2026-11-10 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

THS3110ID datasheet THS3110ID pinout THS3110ID datasheet pdf THS3110ID equivalent THS3110ID replacement THS3110ID vs THS3111ID THS3110ID SOIC-8 pinout THS3110ID application circuit Texas Instruments THS3110ID THS3110ID price THS3110ID stock THS3110ID current feedback amplifier

Componentes & términos relacionados

Texas Instruments THS3110ID THS3111ID THS3110IDR THS3110IDG4 THS3110IDRG4 current-feedback amplifier operational amplifier amplifier IC analog signal processing semiconductor unity-gain bandwidth slew rate voltage noise current noise power-down pin SOIC-8 surface-mount package precision instrumentation communications receiver professional audio high-speed data acquisition video processing
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ