TJA1041T/VM - 1 Mbit/s CAN Transceiver | NXP Semiconductors
MPN: TJA1041T/VM ✗ 停產TJA1041T/VM 概覽
A CAN transceiver is the physical-layer interface between a digital CAN controller and the differential bus wiring. It converts controller logic signals into a dominant or recessive differential bus state and converts bus levels into logic signals for the controller. This type of interface belongs to the hierarchy of CAN transceiver, communication interface IC, interface IC, and semiconductor.
The TJA1041 supports CAN communication rates up to 1 Mbit/s and is primarily intended for high-speed automotive applications. Its differential receiver provides the interface from the bus to the controller, while its differential transmitter connects the node to the CAN network. The TJA1041T/VM package designation identifies the SOIC-14 variant with NXP's VM ordering suffix.
Automotive electronics use CAN networks to connect engine-control, body, chassis, comfort, and diagnostic modules while reducing wiring complexity. A CAN node generally combines a protocol controller with a transceiver such as the TJA1041. The physical transceiver handles bus-level signaling, allowing the controller to exchange frames through a standardized communication interface.
Typical uses include electronic control units, body-control modules, powertrain controllers, gateway electronics, automotive diagnostic interfaces, and industrial CAN equipment connected to 1 Mbit/s networks. Selection should consider bus speed, transceiver logic compatibility, termination strategy, package footprint, operating temperature, and the manufacturer's lifecycle status.
PCB design must preserve the recommended CAN bus routing and termination arrangement, provide a stable transceiver supply, and maintain suitable common-mode behavior for the automotive network. Because the TJA1041T/VM is marked End of Life, new production designs should verify migration options and avoid depending on an unannounced second source.
This product page combines the NXP functional description, package and lifecycle information, ordering references, and practical guidance for selecting, comparing, and implementing a replacement before an End of Life migration.
直接替換替代品,適用於 TJA1041T/VM — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
TJA1041T
✅ 直接替換📋 參考替代品(不在目錄中)
TJA1041T/VM 規格
| Product Type | High-speed CAN transceiver |
| Maximum CAN Data Rate | 1 Mbit/s |
| CAN Transmit Function | Differential |
| CAN Receive Function | Differential |
| Primary Application | Automotive high-speed CAN |
| 封裝 | 14-pin SOIC |
| 安裝類型 | Surface mount |
| 生命週期狀態 | End of Life |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
TJA1041T/VM 14-pin soic 腳位配置指南
TJA1041T/VM(14-pin soic 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: TJA1041T/VM.
請參閱 資料表 以查看完整腳位配置。
典型應用
TJA1041T/VM 適用於 6 應用s: Automotive Electronic Control Unit, Body Control Module, Powertrain Controller, Vehicle Gateway Electronics, Automotive Diagnostic Interface, Industrial CAN Equipment.
Automotive Electronic Control Unit
The TJA1041T/VM suits an automotive electronic control unit that connects a CAN protocol controller to a physical high-speed CAN network. Its differential transmitter and receiver establish the physical interface, while the documented 1 Mbit/s capability aligns with conventional high-speed vehicle networks. The device is placed close to the controller and bus connection, with the PCB arranged to minimize disruption of the differential signal path. Because the family is marked End of Life, the automotive program must confirm the exact orderable suffix, production schedule, qualification requirements, and approved migration before new vehicle launches.
推薦
Body Control Module
A body control module can use the TJA1041T/VM to interface its CAN controller with switches, door modules, lighting electronics, and other body systems sharing the network. The differential signaling reduces sensitivity to common disturbances found in vehicle wiring, while the 1 Mbit/s rating supports high-speed CAN communication. Component placement should follow the manufacturer's application guidance and keep the CAN bus route compact. For current production programs, designers should review NXP's discontinuance information because a lifecycle change can require schematic confirmation, timing review, and updated supplier qualification records.
推薦
Powertrain Controller
The TJA1041T/VM can provide the physical CAN interface in a powertrain controller that exchanges diagnostic and control information with vehicle modules. Its documented support for CAN rates up to 1 Mbit/s is appropriate for the high-speed CAN portion of an automotive network, and its differential transmitter and receiver provide the required bus-side functions. A robust layout must account for automotive electrical conditions, including transient immunity and common-mode behavior. The exact ordering suffix should be checked for temperature grade and qualification, and a lifecycle migration should be planned before the device is specified for a new platform.
推薦
Vehicle Gateway Electronics
A vehicle gateway can use the TJA1041T/VM as the CAN-side interface between a communication processor and a high-speed CAN network segment. The transceiver translates between controller-domain signals and the differential physical bus, supporting communication rates as high as 1 Mbit/s. Gateway boards often combine several communication functions, so the designer should preserve separation between sensitive digital routing and the CAN network wiring while following the manufacturer's recommended termination and layout practices. The End of Life designation makes early replacement planning important for platforms expected to remain in production for many years.
推薦
Automotive Diagnostic Interface
An automotive diagnostic interface can use the TJA1041T/VM to connect diagnostic circuitry or a CAN controller to a high-speed vehicle network. The interface supports differential transmission and reception at CAN rates up to 1 Mbit/s, allowing diagnostic frames to use the same physical network infrastructure as other vehicle modules. The board design must provide the bus interface required by the NXP application guidance and account for vehicle-level common-mode and transient conditions. For new diagnostic equipment, verify the lifecycle and qualification status of the exact suffix rather than treating every member of the TJA1041 family as production-equivalent.
推薦
Industrial CAN Equipment
The TJA1041T/VM can be evaluated for industrial automation equipment that uses a 1 Mbit/s CAN network, provided its electrical limits, temperature range, and automotive qualification status satisfy the application. The differential transmitter and receiver allow a controller to communicate reliably over a multi-node bus while reducing sensitivity to shared ground and cable disturbances. Layout should follow the NXP recommended application circuit and preserve a controlled termination arrangement. Because the product family is marked End of Life, industrial projects should compare an active replacement and verify protocol, timing, and environmental requirements before committing the design.
推薦
推薦產品摘要
工程參考資料,適用於 TJA1041T/VM — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TJA1041T |
|---|---|---|
| Package | SOIC-14 (14-SO) | SOIC-14 (14-SO) |
| Brand | NXP Semiconductors | NXP Semiconductors |
| Product Type | High-speed CAN transceiver | High-speed CAN transceiver |
| Maximum CAN Data Rate | 1 Mbit/s | 1 Mbit/s |
| Transmit Interface | Differential | Differential |
| Receive Interface | Differential | Differential |
| Primary Application | Automotive high-speed CAN | Automotive high-speed CAN |
主要差異化特點
- Documented high-speed CAN capability (對比TJA1041T)
- Identical family architecture and footprint (對比TJA1041T)
- Direct automotive CAN positioning (對比TJA1041T)
設計說明
Follow the NXP TJA1041 recommended application circuit and PCB layout for the CANH and CANN connections. Keep the differential bus route compact and continuous, minimize stubs and branch points, and place the termination component at the physical end of the bus rather than beside the transceiver when the network topology requires distributed termination. These routing practices reduce reflections and help preserve signal integrity on the differential bus.
Design the transceiver supply path with the voltage range, current behavior, and decoupling requirements stated in the manufacturer datasheet. Place the required input capacitance close to the supply and ground pins and keep the return path short. Verify startup, bus dominance, recessive-state behavior, and supply tolerance across the complete operating range rather than checking only nominal operation.
Do not treat similar TJA1041 orderable names as automatically interchangeable. Check the full suffix, package, temperature grade, automotive qualification, tape-and-reel configuration, and lifecycle status in the NXP ordering information. Since the family is marked End of Life, obtain a documented manufacturer replacement or engineering change approval before updating a released vehicle or industrial design.
Separate CAN-bus routing from sensitive analog and high-speed digital paths, and use a continuous ground reference beneath the interface where the package and board construction allow it. Keep the transceiver's bus-side components close to their associated pins and avoid adding long test pads or unused branches to the differential network. Validate the final routing with the manufacturer's guidelines and, where applicable, signal-integrity simulation.
合規資訊
The available manufacturer information identifies the TJA1041T as End of Life and describes automotive high-speed CAN use, but it does not state the required compliance conclusions for this exact ordering suffix.