Texas Instruments

TLV2370ID - 3MHz RRIO Op Amp with Shutdown | Texas Instruments

MPN: TLV2370ID ✓ 啟用中
550 uA Vdss 8-pin SOIC Package
MOQ: 1 |

TLV2370ID 概覽

Texas Instruments TLV2370ID is a single-amplifier operational amplifier with rail-to-rail input and output capability, 3 MHz gain-bandwidth product, 550 uA per channel supply current, and a shutdown control function, housed in an 8-pin SOIC package. It operates from a 2.7 V minimum supply voltage and supports supply voltages up to 16 V.

An operational amplifier is an analog signal-conditioning IC that uses differential feedback to amplify the voltage difference between its inverting and non-inverting inputs. Within the amplifier hierarchy, the TLV2370 belongs to the rail-to-rail input/output amplifier family, combines with other operational amplifiers and buffers, and ultimately supports analog signal chains, sensor interfaces, and power-management systems.

The principal advantages of the TLV2370ID include 3 MHz bandwidth, 2.1 V/us slew rate, rail-to-rail signal handling, and low 550 uA supply current. The shutdown function allows the amplifier to be disabled when the circuit does not need continuous operation. CMOS inputs are particularly useful with high-impedance sensors, while the single-supply architecture simplifies portable and industrial signal-conditioning designs.

The device combines a 3 MHz gain-bandwidth product with a 2.1 V/us slew rate, allowing it to process higher-frequency signals than a low-bandwidth precision amplifier while avoiding the supply current of a much faster high-power op amp. Its rail-to-rail input stage increases input-voltage range, and rail-to-rail output capability supports operation close to the supply rails when suitable load and feedback conditions are used.

Typical uses include battery-powered sensor conditioning, portable measurement systems, low-power industrial instrumentation, audio and communication signal paths, and general-purpose analog filtering. The TLV2370ID can also serve as a buffer when configured with conventional voltage-follower feedback. In each case, circuit headroom, output swing, noise, stability, and shutdown timing should be checked against the actual load and signal frequency.

A practical design consideration is to place the input, feedback, and bypass components close to the amplifier pins. Decoupling capacitance should be selected using the manufacturer guidance, while output loading and feedback values should be chosen to preserve the intended bandwidth and output-voltage swing. The shutdown pin should be driven by a signal that cannot float during reset or power sequencing.

This page combines the device specifications, application guidance, package-level design considerations, and a focused comparison of same-footprint alternatives to support practical amplifier selection and PCB design.

直接替換替代品,適用於 TLV2370ID — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: TLV2370ID (相同外形與佔位) — 差異在於 Amplifier Type, Number of Channels, Package, Slew Rate.

Texas Instruments
Amplifier Type: Single operational amplifier
Number of Channels: 1 channel
Package: 8-pin SOIC
比較對象 TLV2370ID →
Texas Instruments
Amplifier Type: Dual operational amplifier
Number of Channels: 2 channels
Slew Rate: 2.4 V/µs
比較對象 TLV2370ID →
Texas Instruments
Amplifier Type: Quad general-purpose operational amplifier
Number of Channels: 4 channels
Package: 14-pin SOIC
比較對象 TLV2370ID →

TLV2371ID

✅ 直接替換 ⚠️ 規格未經驗證
Texas Instruments
📦 8-pin SOIC
Single operational amplifier · 1 channel · 3 MHz · 2.1 V/us · 2.7 V · 16 V · 550 µA per channel · 4.5 mV

聯絡詢價

查看資料表 →

TLV2372ID

✅ 直接替換 ⚠️ 規格未經驗證
Texas Instruments
📦 8-pin SOIC
Dual operational amplifier · 2 channels · Yes · Yes · 3 MHz · 2.4 V/µs · 550 µA · 2.7 V

聯絡詢價

查看資料表 →

TLV2374ID

✅ 直接替換 ⚠️ 規格未經驗證
Texas Instruments
📦 8-pin SOIC
Quad general-purpose operational amplifier · 4 channels · 16 V · 2.7 V · 3 MHz · 550 uA · Rail-to-rail · Rail-to-rail

聯絡詢價

查看資料表 →

TLV2370IDR

✅ 直接替換
📦 8-pin SOIC
Identical TLV2370 electrical ratings and SOIC-8 pinout; the R suffix changes the tape-and-reel shipment format, producing 0% change in bandwidth, supply current, and supply-voltage ratings.

📋 參考替代品(不在目錄中)

TLV2370IDG4

✅ 直接替換
📦 8-pin SOIC
Shares the TLV2370 electrical function and SOIC-8 footprint; the G4 suffix identifies a lead-free finish, with 0% change in bandwidth, supply current, and supply-voltage ratings.

📋 參考替代品(不在目錄中)

TLV2370ID 最大額定值與電氣特性

Amplifier Type Single operational amplifier
Number of Channels 1 channel
Gain-Bandwidth Product 3 MHz
Slew Rate 2.1 V/us
Supply Current per Channel 550 uA
Minimum Operating Supply Voltage 2.7 V
Maximum Recommended Supply Voltage 16 V
Input Common-Mode Range Rail-to-rail
輸出電壓範圍 Rail-to-rail
Shutdown Control Yes
Input Type CMOS
封裝 8-pin SOIC
安裝類型 Surface mount
Temperature Range Extended industrial temperature range

TLV2370ID 腳位配置

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
腳位 1 OUT — Amplifier output
腳位 2 IN- — Inverting input
腳位 3 IN+ — Non-inverting input
腳位 4 V- — Negative supply; connect to ground for single-supply operation
腳位 5 SHDN — Shutdown control input
腳位 6 NC — Not connected
腳位 7 V+ — Positive supply input
腳位 8 NC — Not connected

典型應用

TLV2370ID 適用於 6 應用s: Battery-Powered Sensor Conditioning, Portable Measurement Instrumentation, Industrial Sensor and Control Interfaces, Low-Power Active Filtering, Communications and Audio Buffering, General-Purpose Analog Signal Conditioning.

🧩

Battery-Powered Sensor Conditioning

The TLV2370ID fits low-voltage sensor interfaces because it combines CMOS inputs, a 2.7 V minimum supply, rail-to-rail input operation, and 550 uA supply current per channel. Place the amplifier directly at the sensor output when the source impedance is high, and use feedback resistors that establish the required gain without adding excessive noise. Its 3 MHz bandwidth handles signals well above the bandwidth of many resistive sensors, while the shutdown control can reduce consumption during idle periods. The main design checks are input bias current, sensor settling behavior, output swing, and whether the selected shutdown state matches the firmware-controlled operating sequence.

📱

Portable Measurement Instrumentation

The TLV2370ID is useful in portable instrumentation where a 3.3 V or 5 V supply leaves limited power budget but moderate analog bandwidth is required. Its 550 uA supply current per channel reduces continuous operating demand, and the 3 MHz gain-bandwidth product supports gain stages, active filters, and signal conditioners operating well above audio frequencies. Rail-to-rail input and output capability helps preserve usable signal range in compact systems. Designers should account for shutdown-control requirements, ADC input settling, noise from high-value feedback resistors, and the amplifier's finite output-current capability when driving a converter, filter, or instrumentation amplifier input.

🏭

Industrial Sensor and Control Interfaces

The TLV2370ID can condition low-level signals in industrial control boards that operate from a 5 V or higher rail while requiring modest bandwidth and low power consumption. Its CMOS input stage is suitable for high-impedance sensors, and the single-supply 2.7 V to 16 V operating range supports both compact embedded systems and higher-voltage industrial rails. The 3 MHz bandwidth allows the amplifier to serve as a buffer or gain stage for slow-to-moderate-speed process variables. Industrial implementations must provide defined shutdown levels, adequate supply bypassing, robust grounding, and protection against transient voltages that could exceed the 16 V maximum recommended supply.

🔧

Low-Power Active Filtering

The TLV2370ID is appropriate for first- and second-order active filters whose signal bandwidth remains well below its 3 MHz gain-bandwidth product. The 2.1 V/us slew rate helps limit large-signal distortion for moderate-amplitude, moderate-frequency waveforms, while 550 uA supply current supports power-limited systems. Use the manufacturer stability guidance when selecting feedback resistors and capacitors, especially for lightly damped filters or capacitive loads. Verify the filter's closed-loop gain, expected input and output frequencies, output load, and supply bypass arrangement. Shutdown can be coordinated with the rest of the acquisition chain when the filter is only needed during a measurement interval.

🌐

Communications and Audio Buffering

The TLV2370ID can buffer moderate-bandwidth communications or audio signals when the circuit requires rail-to-rail operation from a single low-voltage supply. Its 3 MHz bandwidth exceeds the useful range of many voice-band and general audio paths, while the 2.1 V/us slew rate provides adequate response for moderate signal amplitudes. The CMOS input stage supports source impedances that would trouble some older bipolar input stages. Designers should still check output-current demand, load impedance, capacitive loading, and output swing on both signal peaks and DC offset. A series isolation resistor may be appropriate when driving long PCB traces or downstream cable capacitance.

⚡

General-Purpose Analog Signal Conditioning

The TLV2370ID provides a practical general-purpose solution for amplifying, buffering, and level-shifting moderate-frequency analog signals in equipment built around a single supply. Its rail-to-rail input and output stages increase design flexibility, while the 550 uA current draw suits low-power embedded systems. The amplifier can implement non-inverting, inverting, differential, or voltage-follower configurations when component values and signal ranges are appropriate. For each topology, verify the gain-bandwidth allocation, noise contribution of feedback resistors, output headroom, and stable feedback arrangement. Use the shutdown function for duty-cycled operation only after confirming the required logic polarity and startup sequence.

What are the key specifications of TLV2370ID that engineers should know?
The TLV2370ID is a single 3 MHz rail-to-rail input/output operational amplifier operating from 2.7 V to 16 V with 550 uA supply current per channel. According to the Texas Instruments TLV2370 product page and manufacturer datasheet, it also provides 2.1 V/us slew rate, CMOS inputs, and an active shutdown function. The 8-pin SOIC package supports standard surface-mount assembly and compact analog layouts.
What is the operating voltage of TLV2370ID?
The TLV2370ID operates from a 2.7 V minimum supply voltage, with a maximum recommended supply voltage of 16 V. According to the Texas Instruments TLV2370 product page and manufacturer datasheet, its single-supply architecture is suitable for 3.3 V and 5 V systems. The common ground reference is connected to the supply ground, while positive and negative signal excursions must remain within the amplifier's supported input and output ranges.
Where can I download the TLV2370ID datasheet PDF?
The official TLV2370ID technical information is available from the Texas Instruments TLV2370 product page at https://www.ti.com/product/TLV2370. The manufacturer datasheet contains the complete electrical characteristics, pin configuration, typical performance curves, shutdown behavior, and application information. Use the ordering information on the same page to confirm that TLV2370ID corresponds to the 8-pin SOIC package.
Where can I find the TLV2370ID pinout?
The TLV2370ID pin configuration is shown in the pinout section of the Texas Instruments TLV2370 manufacturer datasheet. The device uses an 8-pin SOIC footprint with output, inverting input, non-inverting input, supply, ground, shutdown, and no-connect positions. Confirm pin assignments against the current datasheet before assigning PCB tracks or connecting the shutdown control.
What is the TLV2370ID bandwidth and slew rate?
The TLV2370ID provides a 3 MHz gain-bandwidth product and 2.1 V/us slew rate. According to the Texas Instruments TLV2370 product information, these figures position the amplifier as a general-purpose, low-power device for moderate-frequency analog signals. Small-signal bandwidth and large-signal settling behavior should be evaluated separately because slew rate limits conversion speed for larger output changes.
Is TLV2370ID suitable for battery-powered sensor interfaces?
Yes, the TLV2370ID is suitable for low-voltage, high-impedance sensor interfaces because it combines CMOS inputs, rail-to-rail input operation, a 2.7 V minimum supply, and 550 uA supply current per channel. According to the Texas Instruments TLV2370 product details, the low-voltage operation makes it an alternative to TLC227x-family devices in suitable battery-powered systems. Input bias current, noise, and sensor source impedance remain the principal checks.
TLV2370ID vs TLV2371ID: which is better for a shutdown-controlled amplifier?
The TLV2370ID and TLV2371ID are closely related single-amplifier devices in the same SOIC-8 family, and both are associated with 3 MHz bandwidth, 550 uA operation, and shutdown capability. Their shutdown-control details must be checked in the manufacturer datasheet before substituting them because control polarity and timing can determine the external logic design. For a new design, select the member whose shutdown behavior matches the system controller directly.
What is the difference between TLV2370ID and TLV2370IDR?
The TLV2370ID and TLV2370IDR have the same electrical identity and 8-pin SOIC footprint, while the final suffix identifies the shipment format. According to Texas Instruments ordering information, TLV2370ID is the standard 8-pin SOIC ordering code and TLV2370IDR is the tape-and-reel shipment option. The R suffix changes logistics rather than the core amplifier specification, so board-level electrical compatibility remains unchanged.
When should I choose TLV2370ID over TLV2371ID?
Choose TLV2370ID when its documented shutdown polarity, timing, and electrical limits match the control circuit and signal chain more directly than the TLV2371ID. Both are single 3 MHz, 550 uA, rail-to-rail amplifiers in the SOIC-8 family according to Texas Instruments product information. The decisive criteria are control-pin behavior, offset and drift limits, output capability, and qualification requirements rather than bandwidth alone.
What can replace TLV2370ID without changing the PCB?
The closest PCB-compatible choices are other 8-pin SOIC members of the TLV237x family, provided their pin functions, shutdown behavior, supply range, and output-current limits match the design. According to the Texas Instruments TLV2370 family information, TLV2371ID, TLV2372ID, and TLV2374ID provide related single-amplifier options. A footprint match alone is insufficient; verify the complete pin and control functions in the manufacturer datasheet.
Is TLV2370ID the same as TLV2370IDG4?
The TLV2370ID and TLV2370IDG4 use the same 8-pin SOIC device family and core amplifier function, with the G4 suffix identifying a lead-free finish. According to the Texas Instruments TLV2370 ordering information, the core gain-bandwidth, supply current, rail-to-rail operation, and shutdown functions remain associated with the TLV2370 device family. Confirm the exact ordering code and environmental qualification before releasing production artwork.
How should I design the shutdown control for TLV2370ID?
Drive the TLV2370ID shutdown control from a defined logic level and avoid leaving the pin floating during reset or power sequencing. According to the Texas Instruments TLV2370 manufacturer datasheet, the shutdown function is intended to reduce operating current when the amplifier is not needed. Confirm the active state, logic thresholds, and startup behavior in the current datasheet, then add pull-up or pull-down resistors if the controlling signal can become high impedance.
What are the main design risks when using TLV2370ID?
The main risks are output saturation, incorrect shutdown control, excessive capacitive loading, and unstable feedback networks. According to the Texas Instruments TLV2370 manufacturer datasheet, the amplifier has rail-to-rail output capability but still has load-dependent output swing limits. Check the load current, feedback network, gain-bandwidth interaction, supply decoupling, and signal path for capacitive loading before finalizing the analog layout.
Where can I buy TLV2370ID online?
Use the Request a Quote form on this page to request TLV2370ID availability, current lead time, and a quotation for the exact 8-pin SOIC ordering code. The Texas Instruments product page identifies TLV2370ID as the SOIC package option, while its orderable part details distinguish it from SOT-23-6 and tape-and-reel variants. Provide the required quantity, target shipment date, and inspection level with the inquiry.
What is the price of TLV2370ID?
Current pricing for TLV2370ID is obtained through the Request a Quote form on this page so the commercial response reflects the selected quantity, packaging, market conditions, and delivery requirements. According to the Texas Instruments TLV2370 product page, TLV2370ID is the 8-pin SOIC ordering option, which must be specified exactly when requesting a quotation. No static price should be used for an engineering or purchasing decision.
What is the lead time and stock status for TLV2370ID?
Current TLV2370ID stock and lead time should be requested through the Request a Quote form on this page. The Texas Instruments TLV2370 product page confirms that TLV2370ID is the 8-pin SOIC device, while the quantity and shipment format must be stated with the inquiry. For production planning, request a date-specific commitment rather than relying on a generic catalog availability statement.

工程參考資料,適用於 TLV2370ID — 比較、設計指引及合規資訊。

選型指南

Choose the TLV2370ID for a general-purpose, single-supply analog design that needs 3 MHz bandwidth, rail-to-rail input and output operation, 550 uA supply current, and shutdown control in an 8-pin SOIC footprint. Choose the TLV2371ID when its documented shutdown and precision characteristics better match the control logic or signal chain; both retain the same principal family ratings. TLV2372ID and TLV2374ID are reasonable alternatives within the same footprint family when their specific offset, control, and performance details satisfy the design. Use TLV2370IDR when the required manufacturing format is tape-and-reel, and TLV2370IDG4 when its lead-free finish is required. In every case, verify the complete pin functions, shutdown polarity, supply limits, output swing, and stability requirements against the manufacturer datasheet before substitution.

與替代品比較

參數 本產品 TLV2371ID TLV2372ID TLV2374ID TLV2370IDR TLV2370IDG4
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Gain-Bandwidth Product 3 MHz 3 MHz 3 MHz 3 MHz 3 MHz 3 MHz
Supply Current per Channel 550 uA 550 uA 550 uA 550 uA 550 uA 550 uA
Maximum Recommended Supply Voltage 16 V 16 V 16 V 16 V 16 V 16 V
Minimum Operating Supply Voltage 2.7 V 2.7 V 2.7 V 2.7 V 2.7 V 2.7 V
Input Common-Mode Range Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail
Output Voltage Range Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail
Shipping Code Standard TLV2370ID ordering code Standard family ordering code Standard family ordering code Standard family ordering code Tape-and-reel shipment code Lead-free finish code

主要差異化特點

  • Combines low supply current with moderate signal bandwidth (對比TLV2370IDR)
  • Maintains the same principal family ratings (對比TLV2371ID)
  • Provides a directly available lead-free ordering option (對比TLV2370IDG4)

設計說明

Place the TLV2370ID supply bypass capacitor immediately between pins 7 and 4, with a short and low-inductance return path to the supply ground. Keep the input traces, feedback components, and output trace away from noisy switching nodes and high-current return paths. Because this is an 8-pin SOIC device, route the shutdown signal away from sensitive input and feedback traces to reduce capacitive coupling into the signal path.

Do not treat rail-to-rail output as a zero-volt output at every load or supply condition. Verify the required output range against the manufacturer output-swing characteristics, including load current and temperature. Also avoid leaving the shutdown control floating: define its state during reset, brownout, and power-up. A pull resistor may be necessary if the controller can enter a high-impedance state.

Choose feedback resistors to balance noise, bias-current error, and the amplifier's 3 MHz bandwidth. If the TLV2370ID drives a downstream cable, ADC sampling input, or other capacitive load, evaluate stability and output-current requirements; an isolation resistor near the output can limit capacitive feedback. Confirm settling time for the intended gain and signal bandwidth rather than relying only on the 3 MHz gain-bandwidth figure.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The TLV2370IDG4 suffix identifies a lead-free finish, but no broader RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals status was stated for the target MPN.

資料驗證日期: 2026-11-19 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

TLV2370ID datasheet TLV2370ID pinout TLV2370ID datasheet pdf TLV2370ID price TLV2370ID equivalent TLV2370ID replacement TLV2370ID vs TLV2371ID Texas Instruments TLV2370ID TLV2370ID 3MHz RRIO amplifier TLV2370ID SOIC-8 pinout TLV2370ID shutdown application circuit TLV2370ID low power sensor interface

相關元件與詞彙

Texas Instruments TLV2370ID TLV2371ID TLV2372ID TLV2374ID TLV2370IDR TLV2370IDG4 TLV237x family operational amplifier single amplifier rail-to-rail input/output amplifier analog signal conditioner CMOS input shutdown control 3 MHz gain-bandwidth product 2.1 V/us slew rate 550 uA supply current 2.7 V minimum supply voltage 16 V maximum recommended supply voltage 8-pin SOIC SOIC family surface-mount package battery-powered sensor interface active filter high-impedance sensor
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情