TLV2374ID - 16V 3MHz Quad RRIO Op Amp | Texas Instruments
MPN: TLV2374ID ✓ 啟用中TLV2374ID 概覽
An operational amplifier, or op amp, is a high-gain analog building block used to amplify small voltage signals, buffer inputs, perform active filtering, and drive downstream circuits. The TLV2374 belongs to the voltage-feedback amplifier hierarchy within the broader operational-amplifier and analog-signal-chain category. Four independent amplifiers in one package can reduce board area and simplify routing when a system requires multiple sensing or signal-conditioning channels.
The TLV2374ID combines rail-to-rail input and output operation with a 550 uA per-channel supply-current rating. Its 3 MHz gain-bandwidth product provides more bandwidth than many micropower amplifiers and makes it suitable for moderate-speed filtering and signal amplification. The 16 V maximum supply rating supports conventional 5 V, 8.4 V, and 12 V analog rails used in industrial equipment. Rail-to-rail operation extends usable input and output range toward the supply limits, although output-headroom and load-current limits must still be respected.
The device is intended for low-power, general-purpose analog designs and is identified by Texas Instruments as a standard instrumentation amplifier-family op amp. Four channels in one package can implement matched gain stages, differential-to-single-ended signal conversion, active filters, or sensor-conditioning channels. The 3 MHz bandwidth and low 550 uA per-channel current create a useful operating point when a design needs faster response than ultra-low-power amplifiers but does not justify the power and cost of a high-performance amplifier.
Typical applications include battery-powered sensor interfaces, industrial transducers, portable measurement equipment, audio input stages, and low-frequency active filters. Its low channel current is valuable in systems where four continuously operating amplifiers could dominate the standby-power budget. Where a signal changes rapidly, verify the closed-loop bandwidth, output-swing behavior, settling time, and capacitive-load drive required by the application.
PCB design should preserve the compactness benefit of the quad package without compromising analog performance. Place each bypassing capacitor close to its corresponding supply pin, route high-impedance input nodes with short traces and minimal parasitic capacitance, and keep output paths away from switching nodes. Confirm stability with the actual source impedance, load, and feedback network because amplifier behavior can change when driving capacitive loads or operating near the supply rails.
This page combines manufacturer device information with package-level engineering guidance, application fit, comparison criteria, and drop-in replacement considerations. The TLV2374ID datasheet remains the controlling reference for the complete electrical characteristics, pin assignments, recommended operating conditions, and test conditions used in a production design.
直接替換替代品,適用於 TLV2374ID — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: TLV2374ID (相同外形與佔位) — 差異在於 Amplifier Type, Number of Channels, Gain-Bandwidth Product, Package, Maximum Supply Voltage.
TLV2374IDR
✅ 直接替換📋 參考替代品(不在目錄中)
TLV2374IDG4
✅ 直接替換📋 參考替代品(不在目錄中)
TLV2374ID 最大額定值與電氣特性
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Channels | 4 channels |
| Maximum Supply Voltage | 16 V |
| Minimum Operating Supply Voltage | 2.7 V |
| Gain-Bandwidth Product | 3 MHz |
| Supply Current per Channel | 550 uA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| 封裝 | 14-pin SOIC |
| 安裝類型 | Surface mount |
TLV2374ID 14-pin soic 腳位配置指南
TLV2374ID(14-pin soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: TLV2374ID.
請參閱 資料表 以查看完整腳位配置。
典型應用
TLV2374ID 適用於 6 應用s: Battery-Powered Sensor Conditioning, Industrial Transducer Interface, Portable Measurement Equipment, Audio Input Conditioning, Active Filtering and Active Filters, Low-Voltage Control Systems.
Battery-Powered Sensor Conditioning
The TLV2374ID fits battery-powered sensor-conditioning designs that need four low-power analog channels without accepting the bandwidth limit of an ultra-low-power amplifier. Its 550 uA supply current per channel and 2.7 V minimum operating voltage help constrain battery drain, while the 3 MHz gain-bandwidth product provides useful margin for gain and filtering stages. Place the amplifier close to the sensor interface, use short input routes, and bypass the supply locally. Check the complete sensor excitation and output-swing requirements because low supply voltage and heavy loading can reduce usable output range even when rail-to-rail operation is specified.
推薦
Industrial Transducer Interface
The TLV2374ID is suitable for industrial transducer interfaces that require several gain or buffer channels around one sensor or control node. Its quad configuration allows up to four 16 V operational amplifiers in one 14-pin SOIC package, while 550 uA per channel supports lower-power instrumentation. The 3 MHz gain-bandwidth product is suitable for many temperature, pressure, position, and bridge-sensor conditioning paths. Validate excitation frequency, input impedance, offset accuracy, and output drive against the transducer, and isolate high-current switching nodes from the sensitive analog section.
推薦
Portable Measurement Equipment
The TLV2374ID supports compact handheld and portable measurement equipment where four amplifiers can provide input buffering, active filtering, level conversion, and output conditioning. A 2.7 V minimum supply supports energy-conscious designs, while 550 uA per channel avoids making amplifier bias current the dominant load. The 3 MHz bandwidth gives useful margin for filters with moderate corner frequencies, but the design must account for output headroom at low supply voltages. Use short feedback traces, solid grounding, and local supply bypassing to preserve accuracy and stability.
推薦
Audio Input Conditioning
The TLV2374ID can provide general-purpose preamplifier, buffer, and crossover stages for line-level or low-level audio signals. Rail-to-rail input and output operation is useful when the signal occupies a large portion of a low-voltage supply, and the 3 MHz gain-bandwidth product exceeds the bandwidth of many audio-band signals. The four-channel package supports stereo or multi-channel routing. Check input-noise density, distortion, output-current capability, and load stability because the device is a general-purpose instrumentation amplifier rather than a dedicated low-noise audio part.
推薦
Active Filtering and Active Filters
The TLV2374ID is appropriate for multiple active-filter channels in measurement and control systems because each amplifier provides a 3 MHz gain-bandwidth product within a 550 uA per-channel power budget. Four channels can implement low-pass, high-pass, or notch stages without requiring separate packages. Select feedback resistors and capacitors for the intended corner frequencies, keep the feedback loop compact, and confirm phase margin with the actual source and load impedances. Avoid placing sensitive filter nodes next to switching-regulator traces or high-impedance sensor connections.
推薦
Low-Voltage Control Systems
The TLV2374ID fits compact low-voltage control systems requiring multiple amplifiers for error amplifiers, comparators, current loops, and actuator-signal conditioning. Operation from 2.7 V supports reduced-energy electronics, while rail-to-rail input and output behavior helps utilize narrow supply ranges. The 3 MHz bandwidth is useful for control loops that are faster than audio-band applications. Review the complete control-loop stability, output-swing, capacitive-load, and slew-rate requirements in the manufacturer datasheet, and add decoupling close to the package pins.
推薦
推薦產品摘要
工程參考資料,適用於 TLV2374ID — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TLV2374IDR | TLV2374IDG4 |
|---|---|---|---|
| Package | 14-SOIC | 14-SOIC | 14-SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Channels | 4 channels | 4 channels | 4 channels |
| Maximum Supply Voltage | 16 V | 16 V | 16 V |
| Minimum Operating Supply Voltage | 2.7 V | 2.7 V | 2.7 V |
| Gain-Bandwidth Product | 3 MHz | 3 MHz | 3 MHz |
| Supply Current per Channel | 550 uA | 550 uA | 550 uA |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Shipping Format | Tube ordering form | Tape and reel | Green-roHS-compliant ordering designation |
主要差異化特點
- Four-channel integration in a 14-pin SOIC package (對比TLV2374IDR)
- Low-power operation with useful bandwidth (對比TLV2374IDR)
- Rail-to-rail signal-path capability (對比TLV2374IDG4)
設計說明
Place the supply-bypass capacitor immediately adjacent to the amplifier supply pins and connect it to the ground plane through a short, low-inductance path. Keep the sensitive input and feedback nodes compact, and route them away from switching-node copper, motor-drive outputs, and high-current return paths. Because the TLV2374ID can operate from 2.7 V to 16 V, select a capacitor voltage rating with suitable margin and verify its effective behavior across the complete supply range.
Do not assume that rail-to-rail input and output operation eliminates all headroom or stability constraints. Output current, load capacitance, output impedance, gain, and the selected feedback network still affect usable voltage swing and loop stability. Check the TLV2374 electrical-characteristics tables for the exact load and supply conditions, and include an isolation resistor when driving a capacitive load or long PCB trace.
Use the manufacturer's 14-pin SOIC pin description when assigning signals, and maintain a consistent ground reference for all four channels. Separate each channel's input routing from the power pins where practical, and avoid sharing narrow copper paths between high-impedance sensor inputs and amplifier outputs. Verify the assembled board for unintended coupling, especially when a switching converter, relay, or display interface is located near the quad analog package.
合規資訊
Compliance status was not explicitly stated in the manufacturer product-page result or distributor snippets. The automotive-grade TLV2374-Q1 is a separate product family and must not be treated as qualification for the standard TLV2374ID.