TLV2370ID - 3MHz RRIO Op Amp with Shutdown | Texas Instruments
MPN: TLV2370ID ✓ فعالTLV2370ID نمای کلی
An operational amplifier is an analog signal-conditioning IC that uses differential feedback to amplify the voltage difference between its inverting and non-inverting inputs. Within the amplifier hierarchy, the TLV2370 belongs to the rail-to-rail input/output amplifier family, combines with other operational amplifiers and buffers, and ultimately supports analog signal chains, sensor interfaces, and power-management systems.
The principal advantages of the TLV2370ID include 3 MHz bandwidth, 2.1 V/us slew rate, rail-to-rail signal handling, and low 550 uA supply current. The shutdown function allows the amplifier to be disabled when the circuit does not need continuous operation. CMOS inputs are particularly useful with high-impedance sensors, while the single-supply architecture simplifies portable and industrial signal-conditioning designs.
The device combines a 3 MHz gain-bandwidth product with a 2.1 V/us slew rate, allowing it to process higher-frequency signals than a low-bandwidth precision amplifier while avoiding the supply current of a much faster high-power op amp. Its rail-to-rail input stage increases input-voltage range, and rail-to-rail output capability supports operation close to the supply rails when suitable load and feedback conditions are used.
Typical uses include battery-powered sensor conditioning, portable measurement systems, low-power industrial instrumentation, audio and communication signal paths, and general-purpose analog filtering. The TLV2370ID can also serve as a buffer when configured with conventional voltage-follower feedback. In each case, circuit headroom, output swing, noise, stability, and shutdown timing should be checked against the actual load and signal frequency.
A practical design consideration is to place the input, feedback, and bypass components close to the amplifier pins. Decoupling capacitance should be selected using the manufacturer guidance, while output loading and feedback values should be chosen to preserve the intended bandwidth and output-voltage swing. The shutdown pin should be driven by a signal that cannot float during reset or power sequencing.
This page combines the device specifications, application guidance, package-level design considerations, and a focused comparison of same-footprint alternatives to support practical amplifier selection and PCB design.
جایگزینهای drop-in برای TLV2370ID — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای TLV2370ID (همان فرمفاکتور و فوتپرینت) — متفاوت در Amplifier Type, Number of Channels, Package, Slew Rate.
TLV2371ID
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←TLV2372ID
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←TLV2374ID
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←TLV2370IDR
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
TLV2370IDG4
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
TLV2370ID حداکثر مقادیر مجاز و مشخصات الکتریکی
| Amplifier Type | Single operational amplifier |
| Number of Channels | 1 channel |
| Gain-Bandwidth Product | 3 MHz |
| Slew Rate | 2.1 V/us |
| Supply Current per Channel | 550 uA |
| Minimum Operating Supply Voltage | 2.7 V |
| Maximum Recommended Supply Voltage | 16 V |
| Input Common-Mode Range | Rail-to-rail |
| محدوده ولتاژ خروجی | Rail-to-rail |
| Shutdown Control | Yes |
| Input Type | CMOS |
| بستهبندی | 8-pin SOIC |
| نوع نصب | Surface mount |
| Temperature Range | Extended industrial temperature range |
پیکربندی پین TLV2370ID
| پین 1 | OUT — Amplifier output |
| پین 2 | IN- — Inverting input |
| پین 3 | IN+ — Non-inverting input |
| پین 4 | V- — Negative supply; connect to ground for single-supply operation |
| پین 5 | SHDN — Shutdown control input |
| پین 6 | NC — Not connected |
| پین 7 | V+ — Positive supply input |
| پین 8 | NC — Not connected |
کاربردهای معمول
TLV2370ID مناسب است برای 6 کاربردs: Battery-Powered Sensor Conditioning, Portable Measurement Instrumentation, Industrial Sensor and Control Interfaces, Low-Power Active Filtering, Communications and Audio Buffering, General-Purpose Analog Signal Conditioning.
Battery-Powered Sensor Conditioning
The TLV2370ID fits low-voltage sensor interfaces because it combines CMOS inputs, a 2.7 V minimum supply, rail-to-rail input operation, and 550 uA supply current per channel. Place the amplifier directly at the sensor output when the source impedance is high, and use feedback resistors that establish the required gain without adding excessive noise. Its 3 MHz bandwidth handles signals well above the bandwidth of many resistive sensors, while the shutdown control can reduce consumption during idle periods. The main design checks are input bias current, sensor settling behavior, output swing, and whether the selected shutdown state matches the firmware-controlled operating sequence.
پیشنهادی
Portable Measurement Instrumentation
The TLV2370ID is useful in portable instrumentation where a 3.3 V or 5 V supply leaves limited power budget but moderate analog bandwidth is required. Its 550 uA supply current per channel reduces continuous operating demand, and the 3 MHz gain-bandwidth product supports gain stages, active filters, and signal conditioners operating well above audio frequencies. Rail-to-rail input and output capability helps preserve usable signal range in compact systems. Designers should account for shutdown-control requirements, ADC input settling, noise from high-value feedback resistors, and the amplifier's finite output-current capability when driving a converter, filter, or instrumentation amplifier input.
پیشنهادی
Industrial Sensor and Control Interfaces
The TLV2370ID can condition low-level signals in industrial control boards that operate from a 5 V or higher rail while requiring modest bandwidth and low power consumption. Its CMOS input stage is suitable for high-impedance sensors, and the single-supply 2.7 V to 16 V operating range supports both compact embedded systems and higher-voltage industrial rails. The 3 MHz bandwidth allows the amplifier to serve as a buffer or gain stage for slow-to-moderate-speed process variables. Industrial implementations must provide defined shutdown levels, adequate supply bypassing, robust grounding, and protection against transient voltages that could exceed the 16 V maximum recommended supply.
پیشنهادی
Low-Power Active Filtering
The TLV2370ID is appropriate for first- and second-order active filters whose signal bandwidth remains well below its 3 MHz gain-bandwidth product. The 2.1 V/us slew rate helps limit large-signal distortion for moderate-amplitude, moderate-frequency waveforms, while 550 uA supply current supports power-limited systems. Use the manufacturer stability guidance when selecting feedback resistors and capacitors, especially for lightly damped filters or capacitive loads. Verify the filter's closed-loop gain, expected input and output frequencies, output load, and supply bypass arrangement. Shutdown can be coordinated with the rest of the acquisition chain when the filter is only needed during a measurement interval.
پیشنهادی
Communications and Audio Buffering
The TLV2370ID can buffer moderate-bandwidth communications or audio signals when the circuit requires rail-to-rail operation from a single low-voltage supply. Its 3 MHz bandwidth exceeds the useful range of many voice-band and general audio paths, while the 2.1 V/us slew rate provides adequate response for moderate signal amplitudes. The CMOS input stage supports source impedances that would trouble some older bipolar input stages. Designers should still check output-current demand, load impedance, capacitive loading, and output swing on both signal peaks and DC offset. A series isolation resistor may be appropriate when driving long PCB traces or downstream cable capacitance.
پیشنهادی
General-Purpose Analog Signal Conditioning
The TLV2370ID provides a practical general-purpose solution for amplifying, buffering, and level-shifting moderate-frequency analog signals in equipment built around a single supply. Its rail-to-rail input and output stages increase design flexibility, while the 550 uA current draw suits low-power embedded systems. The amplifier can implement non-inverting, inverting, differential, or voltage-follower configurations when component values and signal ranges are appropriate. For each topology, verify the gain-bandwidth allocation, noise contribution of feedback resistors, output headroom, and stable feedback arrangement. Use the shutdown function for duty-cycled operation only after confirming the required logic polarity and startup sequence.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای TLV2370ID — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | TLV2371ID | TLV2372ID | TLV2374ID | TLV2370IDR | TLV2370IDG4 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Gain-Bandwidth Product | 3 MHz | 3 MHz | 3 MHz | 3 MHz | 3 MHz | 3 MHz |
| Supply Current per Channel | 550 uA | 550 uA | 550 uA | 550 uA | 550 uA | 550 uA |
| Maximum Recommended Supply Voltage | 16 V | 16 V | 16 V | 16 V | 16 V | 16 V |
| Minimum Operating Supply Voltage | 2.7 V | 2.7 V | 2.7 V | 2.7 V | 2.7 V | 2.7 V |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Voltage Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Shipping Code | Standard TLV2370ID ordering code | Standard family ordering code | Standard family ordering code | Standard family ordering code | Tape-and-reel shipment code | Lead-free finish code |
تفاوتهای کلیدی
- Combines low supply current with moderate signal bandwidth (در مقابلTLV2370IDR)
- Maintains the same principal family ratings (در مقابلTLV2371ID)
- Provides a directly available lead-free ordering option (در مقابلTLV2370IDG4)
یادداشتهای طراحی
Place the TLV2370ID supply bypass capacitor immediately between pins 7 and 4, with a short and low-inductance return path to the supply ground. Keep the input traces, feedback components, and output trace away from noisy switching nodes and high-current return paths. Because this is an 8-pin SOIC device, route the shutdown signal away from sensitive input and feedback traces to reduce capacitive coupling into the signal path.
Do not treat rail-to-rail output as a zero-volt output at every load or supply condition. Verify the required output range against the manufacturer output-swing characteristics, including load current and temperature. Also avoid leaving the shutdown control floating: define its state during reset, brownout, and power-up. A pull resistor may be necessary if the controller can enter a high-impedance state.
Choose feedback resistors to balance noise, bias-current error, and the amplifier's 3 MHz bandwidth. If the TLV2370ID drives a downstream cable, ADC sampling input, or other capacitive load, evaluate stability and output-current requirements; an isolation resistor near the output can limit capacitive feedback. Confirm settling time for the intended gain and signal bandwidth rather than relying only on the 3 MHz gain-bandwidth figure.
اطلاعات انطباق
The TLV2370IDG4 suffix identifies a lead-free finish, but no broader RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals status was stated for the target MPN.