TLV2761IP - 500kHz Micropower RRIO Op Amp | Texas Instruments
MPN: TLV2761IP ✓ 啟用中TLV2761IP 概覽
An operational amplifier, or op amp, is a high-gain analog building block used to amplify, buffer, compare, and filter signals. The TLV2761 belongs to the operational amplifier hierarchy, where its rail-to-rail input and output stages allow signals close to the positive and negative supply rails to be processed more effectively than with a conventional input stage. This makes it useful in sensor interfaces, low-voltage signal chains, and portable instrumentation.
The TLV2761IP operates from a single supply of up to 3.6 V and provides 500 kHz gain-bandwidth performance. Its typical supply current is 20 µA, supporting battery-powered and energy-conscious designs. Rail-to-rail input and output operation extends usable signal range within the supply limits, while the general-purpose amplifier configuration provides a practical solution for low-frequency amplification, buffering, and thresholding functions.
The 8-pin PDIP format supports through-hole construction and is useful for prototypes, educational platforms, manually wired test equipment, and designs that benefit from socketed or easily inspected assemblies. Unlike a surface-mount package, the PDIP outline provides generous spacing between leads, making it easier to access with conventional bench instruments. Care is still required to maintain clean supply grounding and stable feedback networks when the amplifier is installed on a prototyping board.
Typical uses include low-voltage sensor interfaces, current or voltage sensing, portable measurement systems, threshold comparators, audio-level conditioning, and general analog signal buffering. In a battery-powered design, its 20 µA typical supply current is the principal power-budget benefit, although actual system consumption also depends on the operating mode, load, and external network. The 500 kHz bandwidth supports moderate-frequency closed-loop operation rather than high-speed signal processing.
Designers should confirm the minimum and maximum supply voltage, input common-mode limits, output swing, shutdown behavior, and stability requirements from the manufacturer datasheet before finalizing the circuit. Decoupling capacitors should be placed close to the supply pins, and feedback components should be selected with the amplifier's recommended operating region in mind. The PDIP package also requires adequate clearance from nearby conductive parts during soldering and inspection.
This page consolidates the manufacturer product identity, verified package and performance information, pin-document location, purchasing workflow, and engineering considerations into a focused guide. It is designed to help engineers confirm fit, assess application suitability, and plan a replacement review without reducing the TLV2761IP to a distributor listing summary.
直接替換替代品,適用於 TLV2761IP — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: TLV2761IP (相同外形與佔位) — 差異在於 Amplifier Type, Number of Circuits, Package.
此產品無可直接替換的替代品。
申請替代品TLV2761IP 最大額定值與電氣特性
| Product Type | Single operational amplifier |
| Manufacturer | Texas Instruments |
| Maximum Supply Voltage | 3.6 V |
| Gain-Bandwidth Product | 500 kHz |
| Typical Supply Current | 20 µA |
| Typical Output Current | 10.2 mA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Number of Circuits | 1 |
| Amplifier Type | General-purpose rail-to-rail input/output |
| Supply Type | Single supply |
| 工作溫度範圍 | -40 °C to 85 °C |
| 封裝 | 8-pin PDIP (P) |
| 安裝類型 | Through-hole |
| 輸出類型 | Rail-to-rail |
TLV2761IP 8-pin pdip (p) 腳位配置指南
TLV2761IP(8-pin pdip (p) 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: TLV2761IP.
請參閱 資料表 以查看完整腳位配置。
典型應用
TLV2761IP 適用於 6 應用s: Battery-Powered Sensor Interface, Portable Voltage Buffer, Threshold and Comparator Circuit, Low-Level Signal Conditioning, Portable Audio Level Conditioning, Test and Measurement Front Panel.
Battery-Powered Sensor Interface
The TLV2761IP fits low-voltage sensor front ends because its single-supply operation extends to 3.6 V and its typical supply current is only 20 µA. Place the amplifier in a non-inverting or differential conditioning stage when the sensor output must be amplified before sampling. Rail-to-rail input and output behavior helps use much of the available supply range, while 500 kHz bandwidth supports sensors and measurement rates below the amplifier's useful closed-loop range. Verify the sensor output against the input common-mode limits and include the bypass capacitor close to the supply pins to prevent supply ripple from entering the measurement path.
Portable Voltage Buffer
The TLV2761IP can buffer a divider or sensor voltage in a compact, battery-operated instrument. Its 20 µA typical supply current minimizes amplifier overhead when the source itself is high impedance, and the single 3.6 V maximum operating supply simplifies power architecture. Configure it as a voltage follower when the source can drive the feedback network, or use a non-inverting gain stage when signal scaling is required. The 500 kHz gain-bandwidth product allows moderate closed-loop bandwidth, but the selected resistor values should maintain suitable loop gain and avoid excessive noise amplification.
Threshold and Comparator Circuit
The TLV2761IP is appropriate for simple threshold detection where one input is driven by a reference and the other by a monitored signal. Rail-to-rail input capability is valuable in a low-voltage system because the input can operate near the supply limits, and the single-amplifier configuration avoids unnecessary power consumption. The device operates from a single supply up to 3.6 V and has a 500 kHz gain-bandwidth product, allowing fast response relative to many low-power general-purpose amplifiers. For a new design, evaluate output saturation, input offset voltage, noise around the threshold, and any need for hysteresis before fixing the switching point.
Low-Level Signal Conditioning
The TLV2761IP can condition low-level analog signals in instrumentation, sensor-conditioning, and educational electronics systems. Its rail-to-rail input stage accepts signals near the supply rails, while its 500 kHz gain-bandwidth product provides sufficient bandwidth for low-frequency and moderate-bandwidth waveforms. The 20 µA typical supply current is especially useful when several amplifier stages operate from a limited energy budget. Use stable feedback resistors, short feedback traces, and a ground reference that remains consistent with the sensor. Offset, input bias current, and output drive should be checked from the datasheet before using the amplifier for high-impedance precision measurements.
Portable Audio Level Conditioning
The TLV2761IP is suitable for buffering or modest gain stages in low-voltage audio-level monitoring circuits. A 3.6 V maximum supply is convenient for portable systems, and the rail-to-rail output stage can provide useful signal swing into a following ADC or comparator stage. The 500 kHz gain-bandwidth product is adequate for voice-band and general audio-conditioning tasks, but it does not target high-fidelity wideband audio performance. Confirm output-noise specifications, output-current capability, and distortion from the manufacturer datasheet. A local supply bypass capacitor and a quiet ground-return layout are important for avoiding added noise in the audio path.
Test and Measurement Front Panel
The 8-pin PDIP package makes the TLV2761IP convenient for test and measurement prototypes that need easy access to input, output, supply, and ground connections. A designer can build a general-purpose gain stage, buffer, or comparator and probe each node with conventional bench equipment. The single-amplifier 3.6 V-class device supports low-voltage portable fixtures, while the 500 kHz bandwidth handles moderate-frequency signals. The through-hole format simplifies rework and socket use, though its larger footprint should be considered in compact instruments. Before installation, verify the manufacturer pin table and ensure the board maintains clean supply decoupling and short feedback paths.
工程參考資料,適用於 TLV2761IP — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Brand | Texas Instruments |
| Package | 8-pin PDIP (P) |
| Product Type | Single operational amplifier |
| Maximum Supply Voltage | 3.6 V |
| Gain-Bandwidth Product | 500 kHz |
| Typical Supply Current | 20 µA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Operating Temperature Range | -40 °C to 85 °C |
主要差異化特點
- Through-hole accessibility (對比TLV9061IDR)
- Low-power single-amplifier configuration (對比TLV2761IP)
- Rail-to-rail signal handling (對比Conventional fixed-common-mode amplifier)
設計說明
Place the supply bypass capacitor as close as practical to the power and ground pins, and keep the amplifier ground return close to the device rather than routing it through a noisy analog or digital return path. Use short feedback traces to minimize parasitic coupling. The 8-pin PDIP outline leaves generous lead spacing, but the PCB should still avoid copper or conductive fixtures beneath the package if soldering, cleaning, or high-voltage isolation conditions require clearance.
Budget the TLV2761IP as a 20 µA typical-load component rather than assuming that this is the complete application supply current. The datasheet current depends on operating mode, and external divider or feedback networks can add their own consumption. For a battery-powered design, estimate the average and peak current using the worst resistor values and the amplifier's actual operating state. Keep the supply at or below the 3.6 V maximum rating, including transients from external sources.
Do not infer an exact replacement from the amplifier family or similar bandwidth alone. A true substitution must preserve the 8-pin PDIP footprint, numbered pin functions, supply limits, rail-to-rail behavior, operating-temperature range, and required output capability. Check whether the circuit uses any shutdown function and confirm the replacement's stability with the selected feedback network and load. Also verify offset voltage, input bias current, output noise, and output-current requirements rather than comparing only the 500 kHz bandwidth figure.
合規資訊
Compliance attributes are not stated on the available product listing and require confirmation from the manufacturer product page or ordering documentation.