TUSB215RGYR - USB 2.0 HS Signal Conditioner | Texas Instruments
MPN: TUSB215RGYR ✓ 啟用中TUSB215RGYR 概覽
A USB high-speed signal conditioner is an interface IC placed within a USB differential data path. It belongs to the USB interface and signal-processing hierarchy, where conditioning components address attenuation, edge distortion, and signal integrity before data reaches a host, device, hub, or cable assembly. Unlike a protocol controller, the TUSB215 does not interpret USB transactions; it reshapes the physical-layer signal traveling across the differential pair.
The principal features of the TUSB215 include USB 2.0 high-speed operation, DC boost capability, an integrated CDP function, VBUS supply support, and a 14-pin VQFN package. Its operating-temperature range is 0 °C to 70 °C. DC boost compensates for voltage loss encountered in a lossy channel, while the integrated charging function supports downstream-port behavior within compatible USB charging designs.
Signal integrity is the central design consideration for this device. TI specifies a 90 Ω differential impedance target for the complete USB high-speed signal path and directs designers to follow high-speed routing guidelines. Differential traces should therefore be length matched, continuously referenced, and routed away from noise-producing or discontinuous structures. Placement close to the source of degradation can provide more effective compensation than placement near the far endpoint.
Typical uses include USB 2.0 host-to-device links, hub connections, peripheral docking systems, cable assemblies, and test equipment that needs channel-loss compensation. The TUSB215 is also relevant to boards that require a CDP function within a compact interface subsystem. Designers must still validate the complete USB channel against applicable electrical compliance requirements because component insertion alone does not guarantee system compliance.
Thermal and layout planning should begin with the exposed-pad VQFN footprint. Place the input, output, and bypass capacitors close to their associated pins, provide a continuous ground reference, and follow the manufacturer land pattern for exposed-pad soldering. The 3.5 mm by 3.5 mm package supports compact designs, but its small thermal area requires careful copper and return-path construction.
This product page combines the device function, package information, application guidance, verified source links, and practical implementation considerations in one engineering-focused reference. It also identifies where electrical details require confirmation in the manufacturer datasheet before a PCB or compliance test is released.
直接替換替代品,適用於 TUSB215RGYR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: TUSB215RGYR (相同外形與佔位) — 差異在於 Product Type.
TUSB213RGYR
✅ 直接替換聯絡詢價
查看資料表 →TUSB213IRGYT
✅ 直接替換📋 參考替代品(不在目錄中)
TUSB213QRGYTQ1
✅ 直接替換📋 參考替代品(不在目錄中)
TUSB215RGYR 規格
| Product Type | USB 2.0 high-speed signal conditioner |
| USB Data Rate | USB 2.0 high speed |
| 供應電壓 | 5 V |
| DC Boost | Supported |
| Charging Function | Integrated CDP |
| VBUS Supply | Supported |
| Differential Impedance Target | 90 ohm |
| Package Type | VQFN-14 (RGY) |
| Package Dimensions | 3.5 mm x 3.5 mm |
| 腳位數 | 14 pins |
| Exposed Pad | Present |
| 工作溫度 | 0 °C to 70 °C |
| 安裝類型 | Surface mount |
| Signal Processing | Compensation for ISI signal loss |
| Compliance Objective | Help passing USB electrical compliance tests |
TUSB215RGYR 3.5 mm x 3.5 mm 腳位配置指南
TUSB215RGYR(3.5 mm x 3.5 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: TUSB215RGYR.
請參閱 資料表 以查看完整腳位配置。
典型應用
TUSB215RGYR 適用於 6 應用s: USB 2.0 Host-to-Peripheral Links, USB Hub Expansion Boards, USB Docking Stations, USB Cable and Dongle Assemblies, USB Compliance Test Equipment, USB Charging-Aware Peripherals.
USB 2.0 Host-to-Peripheral Links
The TUSB215RGYR fits USB 2.0 high-speed paths in which connector launches, cable transitions, or long PCB routes degrade the differential signal. Its DC boost capability compensates for reduced signal amplitude, while the signal-conditioning function addresses channel-related ISI distortion. Place the device near the point where meaningful loss has accumulated rather than at the receiver, and maintain 90 Ω differential impedance across the complete route. Validate the completed link with eye measurements because compliance depends on the installed channel, connector, and enclosure.
推薦
USB Hub Expansion Boards
A USB hub PCB can use the TUSB215RGYR on high-speed routes where repeated connector and trace transitions reduce differential-swing quality. The device's DC boost function helps recover signal amplitude, making it useful near a downstream port after the channel's main loss mechanisms. The 3.5 mm by 3.5 mm VQFN package also saves board area in compact hub designs. Keep the high-speed pair impedance-controlled, route over an uninterrupted reference plane, and confirm hub eye masks and electrical compliance with the complete assembled board.
推薦
USB Docking Stations
Dockings systems often combine exposed connectors, internal cables, adapters, and long PCB routes that can impair USB high-speed signaling. Placing the TUSB215RGYR between the degraded channel and the host receiver can improve signal amplitude and edge quality through DC boost and equalization. Its integrated CDP and VBUS supply support can also simplify compatible charging architectures. The designer should still budget connector clearance, maintain 90 Ω differential routing, and test eye height, rise time, and overshoot across representative dock cable lengths and loading conditions.
推薦
USB Cable and Dongle Assemblies
The TUSB215RGYR is appropriate for compact cable-end or dongle electronics where a long cable or connector assembly introduces USB high-speed loss. The 14-pin VQFN package provides a compact implementation, and DC boost helps compensate for attenuation near the far end of the channel. Because an exposed-pad package requires careful thermal and soldering control, verify assembly reflow capability and provide adequate copper around the pad. Validate the complete cable assembly because connector geometry, strain relief, shielding, and cable construction influence the achieved eye margin.
推薦
USB Compliance Test Equipment
Instrumentation that measures USB eye diagrams, jitter, amplitude, and compliance can use the TUSB215RGYR as a controlled conditioning element in a fixture, channel emulator, or test article. Its DC boost behavior makes it useful when the intended test channel includes enough loss to distort a high-speed differential waveform. Because the device adds its own transfer function, measurements must distinguish conditioner behavior from the cable and fixture under test. Characterize the complete measurement path and calibrate it before using corrected amplitude or compliance results.
推薦
USB Charging-Aware Peripherals
The TUSB215RGYR can support USB peripheral designs that need high-speed data conditioning together with downstream-port charging behavior. Its integrated CDP and VBUS supply support reduce the number of separate functions required in compatible architectures, while the 14-pin VQFN package fits compact controller boards. The charging implementation must follow the device's application circuit and the applicable USB charging requirements. Confirm pin functions, VBUS limits, capacitor selection, and thermal performance before releasing a production design.
推薦
推薦產品摘要
工程參考資料,適用於 TUSB215RGYR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TUSB213RGYR | TUSB213IRGYT | TUSB213QRGYTQ1 |
|---|---|---|---|---|
| Package | VQFN-14 (RGY), 3.5 mm x 3.5 mm | VQFN-14, 3.5 mm x 3.5 mm | VQFN-14, 3.5 mm x 3.5 mm | VQFN-14, 3.5 mm x 3.5 mm |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Primary Function | USB 2.0 high-speed signal conditioner | USB 2.0 high-speed signal conditioner | USB 2.0 high-speed signal conditioner | USB 2.0 high-speed signal conditioner |
| Integrated CDP | Supported | Not identified for the TUSB215 feature set | Not identified for the TUSB215 feature set | Not identified for the TUSB215 feature set |
| VBUS Supply Support | Supported | Not identified for the TUSB215 feature set | Not identified for the TUSB215 feature set | Not identified for the TUSB215 feature set |
| Channel Compensation | Compensation for ISI signal loss | USB high-speed signal conditioning | USB high-speed signal conditioning | USB high-speed signal conditioning |
主要差異化特點
- Integrated charging and VBUS features (對比TUSB213RGYR)
- Same 3.5 mm by 3.5 mm VQFN family footprint (對比TUSB213IRGYT)
- Automotive-oriented family alternative (對比TUSB213QRGYTQ1)
設計說明
Treat the entire USB high-speed route as one controlled channel. Texas Instruments specifies 90 Ω differential impedance for the complete signal path, so use tightly coupled differential traces over a continuous reference plane, minimize layer transitions and stubs, and match the pair length. Place the TUSB215RGYR after the section where appreciable channel loss has accumulated. Verify eye height, differential swing, rise time, and overshoot on the assembled board because compliant component characteristics alone cannot guarantee system-level USB compliance.
Follow the manufacturer's RGY exposed-pad land pattern exactly, including paste geometry and solder-mask design. Provide a continuous ground connection beneath the thermal pad and adequate exposed copper for heat spreading without compromising the high-speed return path. Place input, output, and bypass capacitors close to their associated pins with very short ground returns. The package is only 3.5 mm by 3.5 mm, so small placement errors can add unwanted loop area and reduce the effectiveness of the DC boost and channel compensation.
Do not select TUSB215RGYR merely because another TUSB213-family device has the same VQFN-14 outline. The TUSB215 integrates a CDP and provides VBUS supply support in addition to DC boost, and removing either feature may require board changes. Before substituting an alternative, compare the complete pin-description table, exposed-pad connection, configuration pins, component values, and operating-temperature grade. Also confirm that the selected supplier is quoting the exact RGY orderable rather than a related package or temperature-grade variant.
Use the 5 V supply arrangement and capacitor values specified by the Texas Instruments application circuit. Keep the device's supply and ground connections short, and use a quiet return path to avoid injecting supply noise into the conditioned USB signal. Check the VBUS arrangement when the integrated CDP and VBUS supply functions are used, including source capability, discharge behavior, and protection requirements. The exact maximum currents, capacitor tolerances, and power limits must be confirmed from the manufacturer electrical-characteristics table before production release.
合規資訊
The device is intended to help pass USB 2.0 electrical compliance tests, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified.