VSC7154XYS/C - 36-PHY SAS Expander | Analog Devices
MPN: VSC7154XYS/C ✓ 啟用中VSC7154XYS/C 概覽
A SAS expander is an interface-controller semiconductor that sits between storage initiator logic and SAS target devices. It divides one logical storage connection into multiple physical links and can operate as an edge expander or a fanout expander. The VSC7154XYS/C therefore belongs to the hierarchy of SAS interface controller, I/O expander, interface IC, and semiconductor. In an edge configuration, it adds drive connectivity without requiring additional host-bus adapters; in a fanout configuration, it consolidates multiple expander paths.
The principal feature is its 36 physical-layer channels, combined with support for both 1.5 Gbps and 3.0 Gbps data rates. Thirty-six PHYs provide the physical connectivity required by midrange and enterprise storage systems, including blade servers, JBOD configurations, and RAID systems. One verified distributor listing reports a low power consumption of 500 mW, although system-level power requirements should be evaluated from the complete manufacturer datasheet and the intended board configuration.
The edge-versus-fanout operating mode is user-configurable, allowing one expander design to support different storage topologies. This flexibility is useful when a system must connect multiple disks or enclosure backplanes while retaining high serial-link throughput. Before placing the device in a new design, confirm the supported SAS topology, firmware behavior, clocking requirements, reference design, and power-supply sequencing against the manufacturer documentation.
Signal-integrity management is a central implementation concern because the expander must preserve communication across numerous simultaneous SAS links. PCB routing should use controlled-impedance transmission paths, minimize stub lengths, provide appropriate connector and termination practices, and maintain suitable separation between adjacent high-speed nets. The expander also requires stable supply rails and careful thermal planning when all 36 PHYs are active.
This page consolidates the verified product identity, SAS capabilities, sourcing information, application context, and practical design considerations into one engineering-oriented reference. It also distinguishes documented functions from parameters that require confirmation in the manufacturer datasheet, helping designers avoid unsupported assumptions before schematic capture, firmware integration, and production qualification.
直接替換替代品,適用於 VSC7154XYS/C — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此產品無可直接替換的替代品。
申請替代品VSC7154XYS/C 規格
| Product Type | 36-PHY multimode SAS expander |
| Number of PHYs | 36 PHYs |
| Supported SAS Data Rates | 1.5 Gbps and 3.0 Gbps |
| Supported Expander Modes | Edge and fanout modes |
| Device Category | I/O expander |
| Protocol | Serial Attached SCSI (SAS) |
| ANSI T10 SAS Version 1.0 Support | Supported |
| ANSI T10 SAS Version 1.1 Support | Supported |
| Target Application | Embedded midrange and enterprise storage |
| Storage System 1 | Blade servers |
| Storage System 2 | JBOD configurations |
| Storage System 3 | RAID systems |
| Reported Power Consumption | 500 mW |
| Manufacturer | Analog Devices / Maxim Integrated |
VSC7154XYS/C standard 腳位配置指南
VSC7154XYS/C(standard 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: VSC7154XYS/C.
請參閱 資料表 以查看完整腳位配置。
典型應用
VSC7154XYS/C 適用於 6 應用s: Blade Server Storage Expansion, JBOD Enclosure Backplane, Enterprise RAID Array, Embedded Storage Chassis, Direct-Attach Storage Consolidation, High-Density Storage Enclosure.
Blade Server Storage Expansion
The VSC7154XYS/C fits blade-server designs that need more SAS drive connections than a host-facing controller can provide directly. Its 36 PHYs create a broad physical-link fabric, while support for both 1.5 Gbps and 3.0 Gbps SAS rates accommodates different generation storage targets. Edge operation can add enclosure links near the drives, and fanout operation can consolidate multiple expander paths. The implementation should be validated for connector reach, power sequencing, thermal loading, and firmware behavior in the complete server configuration.
推薦
JBOD Enclosure Backplane
The VSC7154XYS/C is well suited to a JBOD backplane where one SAS domain must reach numerous disks. Thirty-six PHYs provide the physical connectivity needed for multi-drive enclosure designs, and edge mode provides a practical way to extend the host-facing storage path toward the drive backplane. For a production design, preserve controlled-impedance routing, minimize connector and cable transitions, verify the supported SAS link rate at each physical connection, and test power-up sequencing across the expander and attached storage devices.
推薦
Enterprise RAID Array
The VSC7154XYS/C supports enterprise RAID architectures that connect multiple disks, enclosure services, and expansion paths through a SAS fabric. The configurable edge and fanout modes allow system architects to align the expander topology with the controller and enclosure layout, while the 36-PHY count reduces the need for multiple physical-layer blocks. Qualification should cover active-link power, connector reliability, firmware fault handling, and full-array operation with the intended disk population rather than a reduced test configuration.
推薦
Embedded Storage Chassis
Embedded storage chassis can use the VSC7154XYS/C as a central SAS connectivity device when the product must support several external disks, redundant storage paths, or multiple internal enclosures. Its 36-PHY capacity and support for edge and fanout topologies provide flexibility in routing storage traffic behind a common expansion point. Designers should account for ground-plane continuity, return paths, connector launch geometry, and power-supply headroom. The final configuration must also be checked against the manufacturer's supported topology and reference circuitry.
推薦
Direct-Attach Storage Consolidation
The VSC7154XYS/C can consolidate direct-attach storage links into a SAS expansion fabric where a system requires more endpoints than its initiator-facing interface supports. Both 1.5 Gbps and 3.0 Gbps rates provide compatibility options for installed SAS generations, and the user-configurable operating mode supports different enclosure arrangements. This role does not replace a host SAS initiator; the expander remains a bridge between storage endpoints and broader fabric infrastructure. Link training, discovery, failover, and management behavior must therefore be verified with the complete controller set.
推薦
High-Density Storage Enclosure
The 36-PHY count makes the VSC7154XYS/C relevant to high-density storage enclosures where drive connections must be distributed efficiently across internal backplanes. Edge mode can provide local port expansion, while fanout mode can support a hierarchy of enclosure connections. Practical implementation requires careful attention to power delivery because simultaneous SAS activity can increase board-level thermal load. Keep high-speed traces short where possible, provide solid reference planes, observe connector and package layout guidance, and verify enclosure hot-swap or power-cycling behavior in system tests.
推薦
推薦產品摘要
工程參考資料,適用於 VSC7154XYS/C — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Brand | Analog Devices |
| Number of PHYs | 36 PHYs |
| SAS Data Rate | 1.5 Gbps and 3.0 Gbps |
| Expander Modes | Edge and fanout |
| Device Category | SAS I/O expander |
| Protocol Support | ANSI T10 SAS 1.0 and 1.1 |
| Primary Applications | Blade servers, JBODs, and RAID systems |
| Reported Power Consumption | 500 mW |
主要差異化特點
- Broad physical-layer connectivity (對比No verified drop-in alternative)
- Support for two SAS link rates (對比No verified drop-in alternative)
- Flexible storage topology (對比No verified drop-in alternative)
設計說明
Route every SAS connection as a controlled-impedance differential pair with a continuous reference plane and minimized discontinuities. Keep connector launches and package escapes consistent, avoid unnecessary stubs and test pads, and maintain suitable spacing from unrelated high-speed signals. Validate the final topology with the manufacturer reference layout and perform eye-diagram, jitter, and link-training tests on the assembled board.
Budget supply current for the configured number of active PHYs rather than relying only on a nominal operating-power value. Provide local high-frequency decoupling at the supply pins, confirm sequencing requirements in the manufacturer datasheet, and verify that the regulator can support expected link activity without excessive ripple. Measure startup and shutdown behavior in the complete storage system because controller, expander, and disk power states may not change simultaneously.
A storage system may keep many SAS links active concurrently, making board-level thermal performance more important than the reported device power alone. Use the package thermal information and application reference design to select copper area, airflow, and heat-sinking strategies. Test the populated JBOD or RAID chassis at its maximum supported disk count and ambient temperature, including sustained sequential traffic rather than only idle operating conditions.
Follow the manufacturer layer stack, fanout, via, and decoupling guidance when constructing the PCB. Preserve symmetry between each differential pair, avoid placing vias in the high-speed path when practical, and separate clocks, serial links, and sensitive management signals where the reference design recommends it. Confirm the exact package land pattern and pin map before releasing the fabrication files because the package description is not included in the available product listings.
Do not treat an equal PHY count as proof that another SAS expander is interchangeable. Verify the package footprint, pin functions, supply voltages, reference-clock requirements, management interface, firmware, edge and fanout behavior, and supported link rates. Also avoid designing around unverified package, temperature, or electrical values; obtain the complete manufacturer datasheet before schematic release and use its tables as the controlling references.
合規資訊
No explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statements were identified for this product.