XC4VLX25-10FF668I - 24,192-Cell Virtex-4 LX FPGA | AMD
MPN: XC4VLX25-10FF668I ✗ 停產XC4VLX25-10FF668I 概覽
A field-programmable gate array is a programmable digital integrated circuit whose logic, interconnect, and input/output behavior are configured after manufacture. An FPGA sits above simple programmable logic devices in the digital-semiconductor hierarchy because it combines programmable logic blocks, block RAM, programmable I/O, dedicated arithmetic resources, and user-selectable routing. The XC4VLX25 belongs to the Virtex-4 LX family, where LX identifies the general-purpose logic density and architecture tier.
The verified component listings identify 24,192 logic cells, 448 I/O, and a 668-ball grid-array package. This combination supports parallel datapaths and moderate-to-high pin counts on systems with complex control or interface requirements. The -10 designation identifies the performance grade, while the industrial suffix identifies the intended temperature class. A lead-free G-terminal variant of the same speed grade is also listed, providing a sourcing option where the required qualification and board-compatibility conditions are satisfied.
The FPGA uses 90 nm CMOS technology and operates from a 1.2 V core supply according to the family-level comparison information. Its maximum clock frequency is listed as 1,028 MHz. Actual design performance depends on the selected Xilinx development environment, device configuration, clocking topology, memory interfaces, routing congestion, and the speed grade of the production device; a theoretical maximum clock should not be treated as a guaranteed system operating frequency.
Typical Virtex-4 LX design uses cases include industrial control, networking equipment, instrumentation, telecommunications, embedded signal processing, test systems, and high-speed interface aggregation. The 448-I/O device is particularly useful where multiple buses, parallel converters, memory interfaces, clocks, and control signals must coexist on one programmable device. Its relatively large 668-ball package also requires careful PCB layout, power planning, and thermal analysis.
Replacement planning should begin with the exact package and device family because footprint compatibility alone does not guarantee an interchangeable design. AMD support guidance identifies another XC4VLX25 in the same package as the fully compatible route, with speed grade and temperature grade determining suitability. PCB designers must also verify power sequencing, configuration memory, bank voltages, decoupling, differential I/O requirements, and the generated bitstream before approving a substitution.
This page consolidates the device identity, package, temperature class, speed grade, and sourced replacement paths into an engineering-focused comparison. It also separates documented selection criteria from design-dependent performance, helping teams evaluate FPGA replacements without overlooking temperature, tooling, bitstream, or PCB compatibility requirements.
直接替換替代品,適用於 XC4VLX25-10FF668I — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: XC4VLX25-10FF668I (相同外形與佔位) — 差異在於 Device Type, Process Technology, Speed Grade, Package Type, Temperature Grade.
XC4VLX25-11FF668I
✅ 直接替換聯絡詢價
查看資料表 →XC4VLX25-11FF668C
✅ 直接替換聯絡詢價
查看資料表 →XC4VLX25-10FFG668I
✅ 直接替換📋 參考替代品(不在目錄中)
XC4VLX25-10FFG668C
✅ 直接替換📋 參考替代品(不在目錄中)
XC4VLX25-11FFG668C
✅ 直接替換📋 參考替代品(不在目錄中)
XC4VLX25-10FF668I 最大額定值與電氣特性
| Device Type | Virtex-4 LX field-programmable gate array |
| Logic Cells | 24,192 cells |
| I/O Count | 448 I/O |
| 封裝 | 668-ball FCBGA |
| Package Type | Grid-array, BGA |
| Package Height | 2.85 mm |
| Speed Grade | -10 |
| 工作溫度 | -40°C to 100°C |
| Process Technology | 90 nm CMOS |
| Core Supply Voltage | 1.2 V |
| 最大時脈頻率 | 1,028 MHz |
| Product Type | IC FPGA |
| Terminals | 668 terminals |
| 安裝方式 | Surface mount |
| Terminal Pitch | 1.000 mm |
XC4VLX25-10FF668I 2.85 mm 腳位配置指南
XC4VLX25-10FF668I(2.85 mm 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: XC4VLX25-10FF668I.
請參閱 資料表 以查看完整腳位配置。
典型應用
XC4VLX25-10FF668I 適用於 6 應用s: Industrial Control Systems, Signal Acquisition and Processing, Telecommunications Equipment, Test and Measurement, Audio and Communication Processing, Industrial Networking Gateway.
Industrial Control Systems
The XC4VLX25-10FF668I fits industrial controllers requiring 448 I/O to connect sensors, actuators, counters, and parallel industrial buses. Its listed industrial range of -40°C to 100°C supports equipment operating across widely varying ambient conditions. The 24,192-cell Virtex-4 LX device can implement control logic, state machines, communication protocols, and supervisory functions in one programmable device. Designers should allocate I/O banks according to voltage requirements, use the manufacturer power and decoupling guidance, and regenerate timing constraints for the exact -10 production grade before release.
推薦
Signal Acquisition and Processing
The XC4VLX25-10FF668I can serve as the programmable processing core in acquisition equipment because its 24,192 logic cells and 448 I/O support parallel data capture, digital filtering, clocking, and control. The listed 1,028 MHz maximum device clock provides substantial timing headroom for appropriately pipelined designs, although system rates depend on routing and external interface timing. A practical implementation separates sensitive analog capture from the FPGA, applies controlled clocking, and uses deterministic I/O constraints. Timing closure and power analysis must use the selected -10 speed grade rather than the family maximum alone.
推薦
Telecommunications Equipment
The Virtex-4 LX architecture and 448 available I/O make the XC4VLX25-10FF668I applicable to telecommunications line cards, multiplexers, protocol converters, and packet-processing modules. The -10 grade provides a defined performance class for industrial telecommunications equipment, while the 668-ball package supports dense connections to memory, transceivers, clocks, and backplanes. Designers must maintain complete pinout, voltage, decoupling, and differential-signal integrity across the large BGA footprint. Configuration should use a supported boot or JTAG method, and the production bitstream must be regenerated when the exact replacement speed grade changes.
推薦
Test and Measurement
In test and measurement systems, the XC4VLX25-10FF668I can implement timing control, pattern generation, acquisition logic, and communication protocols in parallel. Its 448 I/O reduces the need for external glue logic when connecting multiple instrument buses, trigger lines, converters, and status signals. The listed 1,028 MHz maximum clock is useful for timing architecture planning but does not guarantee equivalent performance at every I/O boundary. Use synchronous design practices, constrain all interface timing paths, and validate clock jitter, skew, and I/O drive requirements against the target measurement specifications.
推薦
Audio and Communication Processing
The XC4VLX25-10FF668I is suitable for programmable audio gateways, synchronizers, channel processors, and communication adapters because it combines 24,192 logic cells with a high I/O count. It can perform sample-rate conversion control, framing, routing, monitoring, and interface adaptation while leaving dedicated converters connected through digital audio interfaces. The industrial temperature range supports equipment intended for extended environmental operation. Audio-system designs must control clocking and grounding carefully, since deterministic clock distribution and clean supply rails are as important as raw logic throughput for low-jitter signal handling.
推薦
Industrial Networking Gateway
The XC4VLX25-10FF668I can implement protocol bridging, traffic classification, buffering control, and supervisory logic in industrial Ethernet gateways. Its 448 I/O provides connectivity for multiple network interfaces, management ports, indicators, and local storage devices. The -10 industrial speed grade supports systems requiring a defined timing class across -40°C to 100°C operation. Because this is a large FCBGA device, successful implementation depends on clean power rails, careful layer transitions, solid return paths under high-speed nets, and manufacturer-recommended decoupling. Validate post-layout timing for every supported network rate.
推薦
推薦產品摘要
工程參考資料,適用於 XC4VLX25-10FF668I — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | XC4VLX25-11FF668I | XC4VLX25-11FF668C | XC4VLX25-10FFG668I | XC4VLX25-10FFG668C | XC4VLX25-11FFG668C |
|---|---|---|---|---|---|---|
| Package | 668-BBGA FCBGA | 668-BBGA FCBGA | 668-BBGA FCBGA | 668-BBGA FCBGA | 668-BBGA FCBGA | 668-BBGA FCBGA |
| Brand | AMD | AMD | AMD | AMD | AMD | AMD |
| FPGA Family | Virtex-4 LX | Virtex-4 LX | Virtex-4 LX | Virtex-4 LX | Virtex-4 LX | Virtex-4 LX |
| Logic Cells | 24,192 cells | 24,192 cells | 24,192 cells | 24,192 cells | 24,192 cells | 24,192 cells |
| I/O Count | 448 I/O | 448 I/O | 448 I/O | 448 I/O | 448 I/O | 448 I/O |
| Speed Grade | -10 | -11, approximately 10% faster grade designation | -11, approximately 10% faster grade designation | -10, same speed grade | -10, same speed grade | -11, approximately 10% faster grade designation |
| Temperature Class | Industrial, -40°C to 100°C | Industrial | Commercial | Industrial | Commercial | Commercial |
| Terminal Finish | Standard suffix; specific finish not stated | Standard suffix | Standard suffix | Lead-free G-terminal designation | Lead-free G-terminal designation | Lead-free G-terminal designation |
| Process Technology | 90 nm CMOS | 90 nm CMOS | 90 nm CMOS | 90 nm CMOS | 90 nm CMOS | 90 nm CMOS |
| Core Voltage | 1.2 V | 1.2 V | 1.2 V | 1.2 V | 1.2 V | 1.2 V |
| Terminal Pitch | 1.000 mm | 1.000 mm | 1.000 mm | 1.000 mm | 1.000 mm | 1.000 mm |
主要差異化特點
- Retains the complete industrial-grade identity when moving to a lead-free package option (對比XC4VLX25-10FFG668I)
- Provides a faster same-package option while preserving logic density and pin count (對比XC4VLX25-11FF668I)
- Maintains the exact -10 speed grade for timing-sensitive redesigns (對比XC4VLX25-11FF668C)
- Combines a -11 speed grade with a lead-free terminal designation (對比XC4VLX25-11FFG668C)
設計說明
Treat the FF668 footprint as a dense, fine-pitch BGA and follow the exact manufacturer ball map, layer stack, and escape-routing guidance. The listed terminal pitch is 1.000 mm, so manufacturing capability, solder-mask definition, via-in-pad use, and board-flatness must be reviewed with the PCB fabricator. Preserve access to configuration pins and confirm that every power and ground ball follows the recommended plane or via pattern.
Before substituting a speed or temperature grade, re-run static and dynamic power analysis and compare I/O current against the exact replacement's electrical limits. A linear change in logic count does not establish equivalent power because speed grade, activity, I/O loading, configuration method, and terminating state can change current. Use manufacturer-recommended supply sequencing, decoupling values, and plane connections for the selected suffix.
A matching BGA footprint does not by itself establish a drop-in replacement. Verify device family, speed grade, temperature class, terminal finish, configuration interface, supported Xilinx tooling, and bitstream compatibility. After changing the exact part, select it in the project, rebuild constraints, review timing and power reports, regenerate the bitstream, and verify configuration over JTAG and the intended production boot path.
Use continuous reference planes and controlled-return routing for high-speed interfaces, especially when the 668-ball package combines external memory, clocks, and I/O. Follow the manufacturer's constraints for length matching, differential pairs, and I/O drive or slew settings. Confirm expansion-board and backplane loss, connector discontinuities, clock jitter, and board skew with realistic timing analysis rather than relying only on device maximum-frequency data.
The package height is listed as 2.85 mm, but the complete thermal resistance and maximum junction-temperature conditions must be taken from the manufacturer package information for the exact board stack-up. Estimate total dissipation from core and I/O power, then confirm copper area, airflow, and adjacent heat sources. Do not reuse thermal margins from another grade or assembly without recalculating the worst-case operating condition.
合規資訊
The target's standard suffix is not identified as lead-free. A separate G-terminal variant is explicitly described as Pb-free in the cross-reference information. No verified RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals declaration is available for the exact target MPN.