XC4VLX25-10FF668I - 24,192-Cell Virtex-4 LX FPGA | AMD
부품 번호: XC4VLX25-10FF668I ✗ 단종XC4VLX25-10FF668I 개요
A field-programmable gate array is a programmable digital integrated circuit whose logic, interconnect, and input/output behavior are configured after manufacture. An FPGA sits above simple programmable logic devices in the digital-semiconductor hierarchy because it combines programmable logic blocks, block RAM, programmable I/O, dedicated arithmetic resources, and user-selectable routing. The XC4VLX25 belongs to the Virtex-4 LX family, where LX identifies the general-purpose logic density and architecture tier.
The verified component listings identify 24,192 logic cells, 448 I/O, and a 668-ball grid-array package. This combination supports parallel datapaths and moderate-to-high pin counts on systems with complex control or interface requirements. The -10 designation identifies the performance grade, while the industrial suffix identifies the intended temperature class. A lead-free G-terminal variant of the same speed grade is also listed, providing a sourcing option where the required qualification and board-compatibility conditions are satisfied.
The FPGA uses 90 nm CMOS technology and operates from a 1.2 V core supply according to the family-level comparison information. Its maximum clock frequency is listed as 1,028 MHz. Actual design performance depends on the selected Xilinx development environment, device configuration, clocking topology, memory interfaces, routing congestion, and the speed grade of the production device; a theoretical maximum clock should not be treated as a guaranteed system operating frequency.
Typical Virtex-4 LX design uses cases include industrial control, networking equipment, instrumentation, telecommunications, embedded signal processing, test systems, and high-speed interface aggregation. The 448-I/O device is particularly useful where multiple buses, parallel converters, memory interfaces, clocks, and control signals must coexist on one programmable device. Its relatively large 668-ball package also requires careful PCB layout, power planning, and thermal analysis.
Replacement planning should begin with the exact package and device family because footprint compatibility alone does not guarantee an interchangeable design. AMD support guidance identifies another XC4VLX25 in the same package as the fully compatible route, with speed grade and temperature grade determining suitability. PCB designers must also verify power sequencing, configuration memory, bank voltages, decoupling, differential I/O requirements, and the generated bitstream before approving a substitution.
This page consolidates the device identity, package, temperature class, speed grade, and sourced replacement paths into an engineering-focused comparison. It also separates documented selection criteria from design-dependent performance, helping teams evaluate FPGA replacements without overlooking temperature, tooling, bitstream, or PCB compatibility requirements.
드롭인 대체품: XC4VLX25-10FF668I — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: XC4VLX25-10FF668I (동일 폼 팩터 및 풋프린트) — 차이점: Device Type, Process Technology, Speed Grade, Package Type, Temperature Grade.
XC4VLX25-11FF668I
✅ 드롭인가격 문의
데이터시트 보기 →XC4VLX25-11FF668C
✅ 드롭인가격 문의
데이터시트 보기 →XC4VLX25-10FFG668I
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
XC4VLX25-10FFG668C
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
XC4VLX25-11FFG668C
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
XC4VLX25-10FF668I 최대 정격 & 전기적 특성
| Device Type | Virtex-4 LX field-programmable gate array |
| Logic Cells | 24,192 cells |
| I/O Count | 448 I/O |
| 패키지 | 668-ball FCBGA |
| Package Type | Grid-array, BGA |
| Package Height | 2.85 mm |
| Speed Grade | -10 |
| 동작 온도 | -40°C to 100°C |
| Process Technology | 90 nm CMOS |
| Core Supply Voltage | 1.2 V |
| 최대 클록 주파수 | 1,028 MHz |
| Product Type | IC FPGA |
| Terminals | 668 terminals |
| 장착 스타일 | Surface mount |
| Terminal Pitch | 1.000 mm |
XC4VLX25-10FF668I 2.85 mm 핀 구성 가이드
XC4VLX25-10FF668I(2.85 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: XC4VLX25-10FF668I.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
XC4VLX25-10FF668I 적합 용도: 6 애플리케이션s: Industrial Control Systems, Signal Acquisition and Processing, Telecommunications Equipment, Test and Measurement, Audio and Communication Processing, Industrial Networking Gateway.
Industrial Control Systems
The XC4VLX25-10FF668I fits industrial controllers requiring 448 I/O to connect sensors, actuators, counters, and parallel industrial buses. Its listed industrial range of -40°C to 100°C supports equipment operating across widely varying ambient conditions. The 24,192-cell Virtex-4 LX device can implement control logic, state machines, communication protocols, and supervisory functions in one programmable device. Designers should allocate I/O banks according to voltage requirements, use the manufacturer power and decoupling guidance, and regenerate timing constraints for the exact -10 production grade before release.
추천
Signal Acquisition and Processing
The XC4VLX25-10FF668I can serve as the programmable processing core in acquisition equipment because its 24,192 logic cells and 448 I/O support parallel data capture, digital filtering, clocking, and control. The listed 1,028 MHz maximum device clock provides substantial timing headroom for appropriately pipelined designs, although system rates depend on routing and external interface timing. A practical implementation separates sensitive analog capture from the FPGA, applies controlled clocking, and uses deterministic I/O constraints. Timing closure and power analysis must use the selected -10 speed grade rather than the family maximum alone.
추천
Telecommunications Equipment
The Virtex-4 LX architecture and 448 available I/O make the XC4VLX25-10FF668I applicable to telecommunications line cards, multiplexers, protocol converters, and packet-processing modules. The -10 grade provides a defined performance class for industrial telecommunications equipment, while the 668-ball package supports dense connections to memory, transceivers, clocks, and backplanes. Designers must maintain complete pinout, voltage, decoupling, and differential-signal integrity across the large BGA footprint. Configuration should use a supported boot or JTAG method, and the production bitstream must be regenerated when the exact replacement speed grade changes.
추천
Test and Measurement
In test and measurement systems, the XC4VLX25-10FF668I can implement timing control, pattern generation, acquisition logic, and communication protocols in parallel. Its 448 I/O reduces the need for external glue logic when connecting multiple instrument buses, trigger lines, converters, and status signals. The listed 1,028 MHz maximum clock is useful for timing architecture planning but does not guarantee equivalent performance at every I/O boundary. Use synchronous design practices, constrain all interface timing paths, and validate clock jitter, skew, and I/O drive requirements against the target measurement specifications.
추천
Audio and Communication Processing
The XC4VLX25-10FF668I is suitable for programmable audio gateways, synchronizers, channel processors, and communication adapters because it combines 24,192 logic cells with a high I/O count. It can perform sample-rate conversion control, framing, routing, monitoring, and interface adaptation while leaving dedicated converters connected through digital audio interfaces. The industrial temperature range supports equipment intended for extended environmental operation. Audio-system designs must control clocking and grounding carefully, since deterministic clock distribution and clean supply rails are as important as raw logic throughput for low-jitter signal handling.
추천
Industrial Networking Gateway
The XC4VLX25-10FF668I can implement protocol bridging, traffic classification, buffering control, and supervisory logic in industrial Ethernet gateways. Its 448 I/O provides connectivity for multiple network interfaces, management ports, indicators, and local storage devices. The -10 industrial speed grade supports systems requiring a defined timing class across -40°C to 100°C operation. Because this is a large FCBGA device, successful implementation depends on clean power rails, careful layer transitions, solid return paths under high-speed nets, and manufacturer-recommended decoupling. Validate post-layout timing for every supported network rate.
추천
추천 제품 요약
엔지니어링 참조 데이터: XC4VLX25-10FF668I — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | XC4VLX25-11FF668I | XC4VLX25-11FF668C | XC4VLX25-10FFG668I | XC4VLX25-10FFG668C | XC4VLX25-11FFG668C |
|---|---|---|---|---|---|---|
| Package | 668-BBGA FCBGA | 668-BBGA FCBGA | 668-BBGA FCBGA | 668-BBGA FCBGA | 668-BBGA FCBGA | 668-BBGA FCBGA |
| Brand | AMD | AMD | AMD | AMD | AMD | AMD |
| FPGA Family | Virtex-4 LX | Virtex-4 LX | Virtex-4 LX | Virtex-4 LX | Virtex-4 LX | Virtex-4 LX |
| Logic Cells | 24,192 cells | 24,192 cells | 24,192 cells | 24,192 cells | 24,192 cells | 24,192 cells |
| I/O Count | 448 I/O | 448 I/O | 448 I/O | 448 I/O | 448 I/O | 448 I/O |
| Speed Grade | -10 | -11, approximately 10% faster grade designation | -11, approximately 10% faster grade designation | -10, same speed grade | -10, same speed grade | -11, approximately 10% faster grade designation |
| Temperature Class | Industrial, -40°C to 100°C | Industrial | Commercial | Industrial | Commercial | Commercial |
| Terminal Finish | Standard suffix; specific finish not stated | Standard suffix | Standard suffix | Lead-free G-terminal designation | Lead-free G-terminal designation | Lead-free G-terminal designation |
| Process Technology | 90 nm CMOS | 90 nm CMOS | 90 nm CMOS | 90 nm CMOS | 90 nm CMOS | 90 nm CMOS |
| Core Voltage | 1.2 V | 1.2 V | 1.2 V | 1.2 V | 1.2 V | 1.2 V |
| Terminal Pitch | 1.000 mm | 1.000 mm | 1.000 mm | 1.000 mm | 1.000 mm | 1.000 mm |
주요 차별점
- Retains the complete industrial-grade identity when moving to a lead-free package option (vs XC4VLX25-10FFG668I)
- Provides a faster same-package option while preserving logic density and pin count (vs XC4VLX25-11FF668I)
- Maintains the exact -10 speed grade for timing-sensitive redesigns (vs XC4VLX25-11FF668C)
- Combines a -11 speed grade with a lead-free terminal designation (vs XC4VLX25-11FFG668C)
설계 노트
Treat the FF668 footprint as a dense, fine-pitch BGA and follow the exact manufacturer ball map, layer stack, and escape-routing guidance. The listed terminal pitch is 1.000 mm, so manufacturing capability, solder-mask definition, via-in-pad use, and board-flatness must be reviewed with the PCB fabricator. Preserve access to configuration pins and confirm that every power and ground ball follows the recommended plane or via pattern.
Before substituting a speed or temperature grade, re-run static and dynamic power analysis and compare I/O current against the exact replacement's electrical limits. A linear change in logic count does not establish equivalent power because speed grade, activity, I/O loading, configuration method, and terminating state can change current. Use manufacturer-recommended supply sequencing, decoupling values, and plane connections for the selected suffix.
A matching BGA footprint does not by itself establish a drop-in replacement. Verify device family, speed grade, temperature class, terminal finish, configuration interface, supported Xilinx tooling, and bitstream compatibility. After changing the exact part, select it in the project, rebuild constraints, review timing and power reports, regenerate the bitstream, and verify configuration over JTAG and the intended production boot path.
Use continuous reference planes and controlled-return routing for high-speed interfaces, especially when the 668-ball package combines external memory, clocks, and I/O. Follow the manufacturer's constraints for length matching, differential pairs, and I/O drive or slew settings. Confirm expansion-board and backplane loss, connector discontinuities, clock jitter, and board skew with realistic timing analysis rather than relying only on device maximum-frequency data.
The package height is listed as 2.85 mm, but the complete thermal resistance and maximum junction-temperature conditions must be taken from the manufacturer package information for the exact board stack-up. Estimate total dissipation from core and I/O power, then confirm copper area, airflow, and adjacent heat sources. Do not reuse thermal margins from another grade or assembly without recalculating the worst-case operating condition.
규정 준수 정보
The target's standard suffix is not identified as lead-free. A separate G-terminal variant is explicitly described as Pb-free in the cross-reference information. No verified RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals declaration is available for the exact target MPN.