集成电路

子分类

📁 ADC/DAC 2520 产品 📁 放大器IC 799 产品 📁 音频编解码器 16 产品 📁 音频IC 2 产品 📁 时钟与计时 312 产品 📁 DSP 963 产品 📁 数据采集IC 2 产品 📁 数字电位器 4 产品 📁 显示驱动与控制器 1 产品 📁 FPGA与CPLD 6666 产品 📁 接口IC 1601 产品 📁 LED驱动器 1 产品 📁 逻辑IC 305 产品 📁 存储IC 875 产品 📁 微控制器 18752 产品 📁 微处理器 4 产品 📁 电机驱动器 1 产品 📁 其他 1 产品 📁 Sensor and Detector Interfaces 1 产品 📁 专用IC 15 产品 📁 视频IC 13 产品

产品（32856)

ADC12DL066CIVS - Dual 12-Bit 66-MSPS ADC, 450MHz BW | TI
ADC12DL066CIVS

ADC12DL066CIVS - Dual 12-Bit 66-MSPS ADC, 450MHz BW | TI

The Texas Instruments ADC12DL066CIVS is a dual-channel, 12-bit, 66-MSPS analog-to-digital converter with 450 MHz analog input bandwidth, housed in a 64-pin TQFP (PAG) package measuring 10x10 mm. It integrates a precision internal reference and operates from a single +3.3 V supply with separate digital I/O supply support from 2.4 V to 3.3 V for easy interfacing to lower-voltage logic. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that samples a continuous-time analog input and converts it to a discrete digital code, serving as the bridge between the analog physical world and digital signal processing. In the broader taxonomy, an ADC is a data converter, which sits within mixed-signal ICs, and ultimately within power management and signal-chain semiconductors. Pipeline ADCs like the ADC12DL066CIVS use multiple low-resolution stages to achieve high sample rates with low latency, suitable for communications and imaging. Key features of this device include a typical differential non-linearity (DNL) of +/-0.5 LSB, signal-to-noise ratio (SNR) of 66 dB at fIN = 10 MHz, and spurious-free dynamic range (SFDR) of similar magnitude at the same input frequency. The pipeline architecture delivers 2-channel simultaneous sampling at 66 MSPS, and the 450 MHz input bandwidth allows the ADC to handle IF-sampling in communications receivers as well as video and imaging front-ends. Internally, the ADC12DL066CIVS uses a pipelined switched-capacitor core with proprietary calibration to maintain linearity and low spurious content across the rated temperature range. The internal reference and built-in sample-and-hold reduce external component count, while power-down mode enables low standby current in battery-powered or duty-cycled systems. Typical applications include IF sampling in software-defined radios, medical ultrasound receive paths, image sensor digitizers, multi-channel data acquisition systems, and industrial instrumentation. It is a drop-in pin-compatible successor to the ADC12D040 within the same 64-TQFP footprint for upgrades seeking higher throughput. Designers should provide a clean low-noise analog supply, good input driving amplifier (often a fully-differential amplifier), and proper PCB layout to avoid coupling digital switching noise into the analog front-end. Decoupling capacitors must be placed close to the supply and reference pins. This page synthesizes distributor pricing, drop-in alternatives, and practical PCB and layout design notes not found in the bare manufacturer datasheet, with comparison tables and trade-off analyses tailored for engineers evaluating mid-speed dual ADCs.

询价 联系我们
ADC12DS080CISQ/NOPB - Dual 12-Bit 80 MSPS ADC, Serial LVDS, 60-WQFN | Texas Instruments
ADC12DS080CISQ/NOPB

ADC12DS080CISQ/NOPB - Dual 12-Bit 80 MSPS ADC, Serial LVDS, 60-WQFN | Texas Instruments

The Texas Instruments ADC12DS080CISQ/NOPB is a dual-channel, 12-bit, 80 MSPS analog-to-digital converter (ADC) with serialized LVDS digital outputs, housed in a 60-lead WQFN (9x9 mm) package with exposed thermal pad. It converts two simultaneous analog input signals into 12-bit digital words at sampling rates up to 80 Mega Samples Per Second (MSPS) per channel, while internal serialization reduces the parallel output bus to a small number of high-speed LVDS pairs. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that converts continuous-time analog voltages into discrete digital codes for processing by DSPs, FPGAs, or microcontrollers. The ADC12DS080 family sits inside the data-converter hierarchy as: ADC -> successive-approximation/pipelined ADC -> high-speed ADC -> mixed-signal IC. Dual-channel parts of this class are the workhorse building blocks of any system that digitizes I/Q baseband, two sensor channels, or differential analog signals simultaneously, enabling coherent multi-channel acquisition without per-channel skew. The ADC12DS080CISQ/NOPB features a pipelined architecture with on-chip sample-and-hold, internal reference, and an LVDS serializer that delivers serialized data on a small number of differential pairs - simplifying PCB routing and reducing EMI compared to parallel CMOS outputs. It operates from a single 3.3 V analog supply and a 3.3 V digital supply, supports -40C to +85C industrial temperature range, and is offered in the Pb-free 60-WQFN package indicated by the /NOPB suffix. The pipelined architecture delivers 12-bit linearity at high sample rates while the LVDS serializer eliminates wide parallel CMOS buses, reducing pin count, switching noise, and ground-bounce. Internal duty-cycle correction and programmable data-clock edge alignment let the host FPGA or ASIC capture data cleanly at full throughput without complex external calibration. Typical applications include portable or bench-top oscilloscopes and digitizers, communications test equipment (cable modem downstream, Wi-Fi/4G baseband digitizers), medical imaging front ends such as ultrasound receivers, dual-sensor industrial data acquisition systems, and radar / LiDAR preprocessing where two channels must be sampled simultaneously. When designing with this part, provide clean 3.3V analog and digital rails and decouple the AVDD/DVDD pins with separate ferrite-bead-isolated planes; route the LVDS pairs as 100 ohm differential and place the reference decoupling capacitor within 3 mm of the REF pins. Note that the /NOPB suffix confirms lead-free / RoHS compliance for global manufacturing. This page synthesizes distributor pricing tiers, drop-in same-brand variants, and practical layout / decoupling notes not collected on the manufacturer product page.

询价 联系我们
ADC12EU050CIPLQ/NOPB - Octal 12-Bit 50 MSPS Sigma-Delta ADC | TI
ADC12EU050CIPLQ/NOPB

ADC12EU050CIPLQ/NOPB - Octal 12-Bit 50 MSPS Sigma-Delta ADC | TI

The Texas Instruments ADC12EU050CIPLQ/NOPB is an octal 12-bit, 45-50 MSPS continuous-time sigma-delta analog-to-digital converter housed in a 68-pin VQFN (10x10 mm) package. The device integrates eight ADC channels with differential inputs, LVDS/serial data interface, and consumes ultra-low power while targeting high-performance multi-channel data acquisition applications. According to the Texas Instruments datasheet, the analog supply operates from 1.14V to 1.26V with a digital I/O supply from 1.4V to 3.6V. A sigma-delta ADC is a converter architecture that oversamples the input signal at a much higher rate than Nyquist, then uses noise-shaping feedback to push quantization noise out of the signal band, followed by digital decimation filtering to produce a high-resolution, low-noise output. Unlike successive-approximation-register (SAR) or pipeline ADCs that resolve in a single clock period, sigma-delta converters trade conversion speed for resolution and inherent anti-alias filtering, making them well suited to high-accuracy, low-to-medium bandwidth applications where noise rejection matters more than raw throughput. Key features include 12-bit native resolution, sampling rates of 40-50 MSPS per channel, 8 fully differential input channels, ultra-low power dissipation per channel, an LVDS-compatible high-speed digital interface, and internal reference plus reference buffer. The architecture eliminates the need for an external anti-alias filter on each channel, simplifying multi-channel PCB layout. Industrial temperature range of -40C to +85C allows use in non-automotive embedded systems, while the 10x10 mm 68-VQFN package keeps per-channel board area low for high channel-count designs. Typical applications span medical imaging front ends, multi-channel sonar and radar receivers, communications base-station digitizers, industrial vibration and machine-condition monitoring, high-channel-count test and measurement instrumentation, and professional audio interfaces requiring simultaneous sampling of multiple analog sources. Each channel can be sampled simultaneously without phase skew between channels. When designing with this part, pay attention to the LVDS data interface layout - keep the LVDS traces impedance-controlled at 100 ohms differential and length-matched to the FPGA or ASIC receiver. Decouple each analog supply pin with a 0.1uF ceramic capacitor placed within 2 mm of the pin to prevent the high-speed switching noise from coupling back into the analog input. This page synthesizes distributor pricing, datasheet specifications, drop-in alternatives, and practical design guidance not found in the manufacturer datasheet alone.

询价 联系我们
ADC12H032CIWM - 12-Bit+Sign SAR ADC, 8-Ch MUX, Serial I/O | TI
ADC12H032CIWM

ADC12H032CIWM - 12-Bit+Sign SAR ADC, 8-Ch MUX, Serial I/O | TI

The Texas Instruments ADC12H032CIWM is a self-calibrating 12-bit plus sign serial I/O analog-to-digital converter with an integrated 8-channel analog multiplexer and sample/hold, housed in a 20-pin wide-body SOIC (SOIC-20, 0.295"/7.50mm width) package. The device family (ADC12H030/ADC12H032/ADC12H034/ADC12H038) provides successive-approximation conversion at throughputs up to 54 ksps with self-calibration logic that nulls offset and linearity errors at power-up. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that converts a continuous analog voltage on its input into a discrete digital code representing that voltage. A successive-approximation register (SAR) ADC uses a binary-search algorithm against an internal DAC, trading conversion speed for high resolution at low power. ADCs sit at the analog boundary of data-acquisition systems (DAQs), which themselves belong to the broader mixed-signal / power-management signal-chain hierarchy. The 12-bit plus sign format (sometimes called 12-bit + sign or sign-extended 12-bit) gives an effective 13-bit two's-complement code covering -Vref to +Vref, ideal for bipolar sensor signals. Key features of the ADC12H032CIWM include: differential nonlinearity (DNL) of +/-1 LSB max, integral nonlinearity (INL) of +/-1 LSB max, self-calibration that runs automatically on command, and an NSC MICROWIRE-compatible serial interface that simplifies connection to microcontrollers and DSPs. The 8-channel analog input MUX lets one ADC IC scan eight sensors, dramatically reducing system cost and PCB area in multi-channel instrumentation. The architecture combines an input MUX, a track/hold amplifier, a successive-approximation ADC core with calibration registers, and a serial output state machine. On-chip calibration trims the internal capacitor mismatch and reference scaling, delivering specified accuracy without external trimpots. The wide-body SOIC-20 footprint provides generous lead spacing for hand-soldering and inspection while remaining suitable for automated SMT lines. Typical applications include multi-channel data acquisition systems, industrial process control and sensor monitoring, battery-cell monitoring, portable instrumentation, and embedded closed-loop control. Designers select this part when they need multiple analog inputs read by a single MCU with minimal board space and software-controlled channel switching. When designing with this ADC, place 0.1 uF bypass capacitors close to the supply pins, follow the datasheet's reference-capacitor network exactly (a 0.1 uF ceramic plus a 1 uF tantalum in parallel is common), and respect the serial-clock timing margins of the MICROWIRE interface. The self-calibration routine should be invoked once after power-up and after any significant temperature change. This page synthesizes distributor pricing, drop-in alternatives from the same ADC12H030/032/034/038 family, and practical design notes that go beyond the manufacturer datasheet's specification tables.

询价 联系我们
ADC12H038CIWM/NOPB - 12-Bit+Sign 8-Ch SAR ADC | Texas Instruments
ADC12H038CIWM/NOPB

ADC12H038CIWM/NOPB - 12-Bit+Sign 8-Ch SAR ADC | Texas Instruments

The Texas Instruments ADC12H038CIWM/NOPB is a self-calibrating 12-bit plus sign serial I/O analog-to-digital converter with an 8-input (4 differential) multiplexer and integrated sample-and-hold, housed in a 28-pin SOIC (IWM) package. It performs successive-approximation (SAR) conversions at speeds up to 182 ksps and includes on-chip self-calibration that corrects for offset and linearity errors at power-up, reducing external trimming requirements to zero. An SAR ADC is a type of analog-to-digital converter that uses a binary-weighted capacitor network and a comparator to perform a bit-by-bit successive search of internal voltage. The ADC12H038 belongs to the data-converter family within the broader mixed-signal and signal-chain IC category, sharing its taxonomy with delta-sigma, pipeline, and flash converters. Its built-in MUX and sample/hold let one ADC serve multiple analog sources, which is a common reason engineers choose SAR over a per-channel dedicated ADC. Key features include 12-bit resolution plus sign extension (yielding 13 bits of effective dynamic range when measuring bipolar signals), an 8-channel single-ended or 4-channel differential input MUX, an integrated sample-and-hold, on-chip self-calibration, and a MICROWIRE-compatible serial interface. The serial I/O reduces pin count versus parallel-output ADCs, enabling 28-SOIC packaging rather than the wider 40- or 44-pin alternatives typically required for 12-bit parallel parts. Input ranges are bipolar-friendly thanks to the sign-bit output, and the part operates from a single 5 V analog supply with 5 V digital I/O. The device is built on a CMOS SAR architecture with a capacitive DAC ladder, which inherently provides no pipeline latency and allows the ADC to be multiplexed across many channels with deterministic per-channel conversion time. Self-calibration runs at power-up and on demand via a software command, measuring internal offset and gain errors and storing correction coefficients, which simplifies manufacturing and supports industrial temperature grades (-40 °C to +85 °C). Typical applications include industrial process control and instrumentation, portable battery-powered measurement, multi-sensor data logging, programmable logic controllers (PLC) analog input modules, automotive sensor interface boards, and portable medical monitoring equipment. The integrated MUX and self-calibration specifically suit cost-sensitive multi-channel designs. When designing with this device, decouple VCC and VREF separately with 0.1 µF ceramic capacitors placed close to the pins, and keep digital return currents isolated from analog ground using a star-ground or split-plane layout. Do not exceed the maximum sampling rate without ensuring the source impedance is low enough to settle the input within the acquisition window. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
ADC12H038CIWMX - 12-Bit+Sign SAR ADC 8-Channel 28-SOIC | TI
ADC12H038CIWMX

ADC12H038CIWMX - 12-Bit+Sign SAR ADC 8-Channel 28-SOIC | TI

The Texas Instruments ADC12H038CIWMX is a self-calibrating 12-bit plus sign successive-approximation analog-to-digital converter with an 8-channel analog input multiplexer and integrated sample/hold, housed in a 28-pin SOIC wide-body package. It supports a 4.5 V to 5.5 V analog supply, provides 8 single-ended or 4 pseudo-differential input channels, and uses the MICROWIRE-compatible serial interface for compact PCB routing with a microcontroller. The architecture supports throughput up to 73.7 kSamples/s when clocked appropriately, with 12-bit resolution plus an additional sign bit that effectively delivers 13 bits of dynamic range for bipolar inputs. An SAR (successive-approximation register) ADC is one of the primary categories of analog-to-digital converters, alongside Delta-Sigma, pipeline, and dual-slope architectures. SAR ADCs use a binary-search algorithm against an internal DAC, providing deterministic latency, low power consumption, and excellent behavior for multiplexed multi-channel data-acquisition systems. ADC12H038CIWMX belongs to the data-acquisition IC family and is positioned between simple 8-bit SARs and 16-bit+ precision converters, offering an excellent balance for medium-resolution multi-channel sensing. Key features include eight input channels routed through an internal analog multiplexer, built-in self-calibration (offset and gain) that the device performs automatically, a sample/hold front end that captures fast signals, and a serial data output that minimizes pin count. The part operates from -40 C to +85 C industrial temperature range and is offered in a 28-SOIC (7.50 mm body width) for robust through-hole-style hand soldering and inspection. Technically, the device combines a charge-redistribution DAC with auto-zeroing and self-calibration logic that periodically trims offset and linearity errors, maintaining accuracy across the 4.5 V to 5.5 V supply range. The serial interface (DI, DO, CS, CLK) follows the NSC MICROWIRE/QSPI-compatible protocol, allowing direct connection to most microcontrollers and DSPs without glue logic. Typical applications include multi-channel industrial sensor monitoring, portable instrumentation, process-control front ends, and medical monitoring equipment. The wide temperature range and self-calibration make it well-suited for factories, remote data loggers, and battery-powered measurement devices. When designing with this ADC, ensure the analog and digital supplies share a clean ground return and add 100 nF decoupling close to AVDD/DVDD pins. Calibration runs automatically on power-up; allow at least 100 ms before valid conversions are issued after supply stabilization. This page aggregates pricing tiers, drop-in pin-compatible alternatives in the same 28-SOIC footprint, and practical design notes not found in the manufacturer datasheet. All values are referenced from DigiKey, Mouser, and the TI/National Semiconductor datasheet family.

询价 联系我们
ADC12J4000NKE10 - 12-Bit 4 GSPS RF-Sampling ADC | Texas Instruments
ADC12J4000NKE10

ADC12J4000NKE10 - 12-Bit 4 GSPS RF-Sampling ADC | Texas Instruments

The Texas Instruments ADC12J4000NKE10 is a 12-bit, 4.0-GSPS RF-sampling analog-to-digital converter with an integrated digital downconverter (DDC), housed in a 68-lead VQFN (10x10 mm) package. The "10" suffix denotes the 10x10 mm VQFN package size and -40C to +85C industrial temperature range. The converter features up to 4 GSPS sample rate, an input bandwidth of 3.2 GHz, and a 64-tap DDC that can decimate complex IF signals in real time. An RF-sampling ADC is a high-speed converter designed to directly digitize wideband radio-frequency analog signals at the carrier or intermediate frequency, eliminating the need for traditional analog mixer-based downconversion stages. The ADC12J4000 belongs to the hierarchy of analog-to-digital converters -> data converters -> signal chain ICs -> semiconductor devices, and supports direct RF digitization where IF or RF signals are sampled at GHz rates without an analog mixer. Key features include a 12-bit resolution with 4.0 GSPS minimum sample rate, 3.2 GHz input bandwidth, integrated 64-tap DDC block with complex decimation ratios, 8 configurable JESD204B serial-output lanes up to 8 Gbps, a 1.2/1.3/1.8V core supply with 2.5V analog supply, and an LVDS-compatible clock input. The folding-interpolating architecture provides very low latency and deterministic aperture delay suitable for radar and instrumentation systems. The ADC12J4000 uses a differential bipolar front-end combined with on-chip dithering to maintain spurious-free dynamic range (SFDR) performance above 65 dBFS at high input frequencies. The integrated DDC includes a numerically controlled oscillator (NCO) and programmable decimation filters supporting divide ratios from 4 to 65536, reducing downstream FPGA fabric requirements by 10-100x in real-time spectral analysis. Typical applications include wideband digital oscilloscopes, spectrum analyzers, electronic warfare (EW) receivers, radar pulse-Doppler processing, L-band and S-band direct-IF sampling, software-defined radio (SDR) platforms, and 5G massive-MIMO base-station digitizers. Designers typically pair the ADC with TI's LMK04828 clock conditioner and a Kintex/Virtex-class FPGA implementing JESD204B decoders. When designing with the ADC12J4000, ensure the analog supply (VA) is decoupled with at least 10uF bulk and 0.1uF ceramic capacitors within 1 cm of the supply pins, and that differential analog inputs are transformer-coupled (e.g., TC1-1-13M+) with 100-ohm external terminations. The JESD204B link requires an 8B/10B-encoded subclass-1 deterministic-latency link with a SYSREF pulse aligned to the device clock.

询价 联系我们
ADC12L030CIWM/NOPB - 12-Bit+Sign SAR ADC, Serial I/O, 16-SOIC | TI
ADC12L030CIWM/NOPB

ADC12L030CIWM/NOPB - 12-Bit+Sign SAR ADC, Serial I/O, 16-SOIC | TI

The Texas Instruments ADC12L030CIWM/NOPB is a 12-bit plus sign, self-calibrating, successive-approximation analog-to-digital converter with serial I/O, a configurable input multiplexer, and an on-chip sample/hold, packaged in a 16-pin wide-body SOIC (IWM). The converter operates from a single 3.3V supply, supports the MICROWIRE-compatible serial interface, and provides one differential input channel in the 1-MUX ADC12L030 configuration. On-chip self-calibration corrects linearity and offset errors at power-up and on demand via a calibration pin, eliminating the need for external trims and ensuring full 12-bit performance across temperature. The plus-sign data format extends the effective input range to span bipolar signals from -VREF to +VREF using a single supply rail, simplifying the analog front end in mixed-signal designs. The serial interface reduces pin count and isolates noisy digital switching from the analog signal path, making the ADC12L030 well suited for compact data-acquisition boards and process-control modules. A successive-approximation register (SAR) ADC is a type of data converter that performs a binary search against the analog input using an internal DAC, producing a digital output in N clock cycles for N bits of resolution. SAR converters are valued for zero-latency single-shot conversions, deterministic behavior, and inherent monotonicity, which makes them well suited for multiplexed multi-channel data acquisition, industrial instrumentation, and precision control loops. The ADC12L030 belongs to the SAR converter family, sits under the broader analog-to-digital converter category, and is commonly used as the precision front end of larger data-acquisition systems that stream samples to a microcontroller or DSP via SPI or MICROWIRE. Key features include 12-bit plus sign resolution, self-calibration, on-chip MUX, internal sample/hold, single 3.3V operation, serial (MICROWIRE/SPI) digital interface, low power consumption, and industrial -40C to +85C temperature range. The serial output reduces I/O count for the host MCU and avoids wide parallel data buses that can couple switching noise into the analog front end, while the wide-body SOIC package supports robust hand-soldering and inspection on legacy and through-hole-friendly layouts. The architecture combines a charge-redistribution DAC, a high-bandwidth comparator, and an SAR register to deliver inherent monotonicity and low-latency conversions, while the self-calibration logic compensates for the DAC, comparator offset, and reference errors. This combination is well suited to battery-powered and portable instruments where power budget and dynamic range must coexist on a single low-voltage rail. Typical applications include portable and battery-powered data loggers, industrial process control modules, pen-tablet digitizers, instrumentation front ends, and remote-sensor signal conditioning. The wide operating temperature range and small footprint also suit HVAC controls, smart sensor nodes, and factory-automation analog input cards. The internal MUX simplifies multi-source monitoring on a single converter, reducing board area and BOM cost versus discrete signal chains. When designing, reserve a 0.1uF ceramic bypass capacitor within a few millimeters of the supply pin and keep analog/digital ground returns separated, joining at a single star point to preserve the rated SNR. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes for the ADC12L030CIWM/NOPB that go beyond a single datasheet extract.

询价 联系我们
ADC12L032CIWM - 12-Bit+Sign SAR ADC, 2-Ch, SOIC-20 | TI
ADC12L032CIWM

ADC12L032CIWM - 12-Bit+Sign SAR ADC, 2-Ch, SOIC-20 | TI

The Texas Instruments ADC12L032CIWM is a 3.3 V, self-calibrating, 12-bit-plus-sign successive-approximation register (SAR) analog-to-digital converter with a 2-channel input multiplexer and integrated sample/hold, housed in a 20-pin SOIC (300-mil, EIAJ) package. Per the manufacturer datasheet, the converter supports sample rates up to 73 ksamples/s (0.73 MHz) with a conversion time of 8.8 us, and runs from a single 3.0 V to 5.5 V analog supply with low power consumption suitable for battery and portable systems. What is an SAR ADC? A successive-approximation register analog-to-digital converter is a precision data-conversion topology that uses a binary-search algorithm to convert an analog input into a digital code. SAR ADCs sit in the converter hierarchy between flash converters (fastest, lowest resolution) and sigma-delta converters (highest resolution, slower). They offer an attractive trade-off of moderate speed, high accuracy, modest power, and a small footprint, making them the workhorse of industrial process control, instrumentation, and portable data-acquisition systems. Key differentiating specifications include 12-bit-plus-sign resolution, on-chip self-calibration that reduces offset and gain errors at power-up and on demand, a flexible serial interface compatible with NSC MICROWIRE and SPI, and 2 analog input channels that expand to 1, 2, or pseudo-differential configurations via the MUX. The device is specified for operation from -40C to +85C (industrial grade), making it robust for harsh environments while remaining in a compact surface-mount package. Typical applications include portable instrumentation, sealed-battery data loggers, isolated sensor read-out, panel-meter front-ends, and multichannel sensor-conditioning boards. The 3.3 V supply and low current draw align naturally with lithium-thionyl-chloride and lithium-ion battery chemistries, and the serial interface minimizes microcontroller pin count in space-constrained designs. When designing with this ADC, ensure the analog supply is decoupled with a 0.1 uF ceramic capacitor placed as close as possible to the AVDD pin, and route digital lines away from analog traces. The self-calibration cycle must be initiated after power-up and after any major temperature change to maintain specified accuracy over temperature and time.

询价 联系我们
ADC12L034CIWM - 12-Bit 4-Channel 3.3V Serial ADC | SOIC-24
ADC12L034CIWM

ADC12L034CIWM - 12-Bit 4-Channel 3.3V Serial ADC | SOIC-24

The Texas Instruments ADC12L034CIWM is a 12-bit plus sign, 4-channel, 3.3V self-calibrating successive-approximation analog-to-digital converter (ADC) with serial I/O, integrated 4-input multiplexer, and sample/hold amplifier, packaged in a 24-pin SOIC Wide (7.5 mm body width). It supports single-ended, pseudo-differential, or fully-differential inputs, communicates via SPI/QSPI/MICROWIRE-compatible serial interface, and includes on-chip self-calibration for offset and linearity correction that eliminates the need for external trimming. The converter accepts a 3.3V analog supply (3.0V to 5.5V tolerant on digital I/O in some datasheet versions), runs at up to 5 MHz serial clock, and offers a 1:1 S/H-to-ADC ratio with one active converter. Per Texas Instruments/National Semiconductor datasheet, this part was originally branded NSC before TI acquired National Semiconductor in 2011, and the datasheet is shared with the ADC12L030/032/038 family (2/8/12 channel variants). A successive-approximation register (SAR) ADC is a precision data converter that performs binary search on the analog input using an internal DAC and comparator, producing one conversion result per N clock cycles for N-bit resolution. SAR ADCs excel at low-latency, mid-speed, multi-channel acquisition because each sample is taken on demand rather than pipelined, and there is no latency between sample and result. Within the power-management and data-acquisition hierarchy, SAR ADCs sit between comparators (1-bit threshold) and delta-sigma ADCs (oversampled, highest resolution). Multi-channel SARs like the ADC12L034CIWM integrate a front-end multiplexer so a single converter can digitize many sensors, reducing BOM cost and PCB area. Key features of the ADC12L034CIWM include 4 analog input channels, 12-bit resolution plus a sign bit enabling bipolar analog ranges around a common-mode reference, hardware-controlled self-calibration for offset and gain, flexible serial interface modes, low operating current suitable for battery-powered designs, and an SOIC-24 wide-body footprint. The SOIC-24W package simplifies hand-prototyping and rework versus smaller QFN packages while still supporting surface-mount assembly. Architecturally, the device combines a charge-redistribution DAC array, comparator, SAR logic, calibration registers, an input MUX, and a dedicated sample-and-hold capacitor that captures the input at the start of conversion. The calibration cycle stores correction coefficients that are applied to subsequent conversions, mitigating internal comparator offset and capacitor mismatch errors that would otherwise limit integral nonlinearity. Typical applications include portable instrumentation, multi-channel sensor digitizers (e.g., four thermocouples, four strain gauges, four process-control signals), handheld meters, industrial PLC analog input modules, and battery monitoring. Any 4-channel, low-frequency, low-power front-end that needs serial I/O to a microcontroller or DSP is a candidate footprint for this part. When designing with this device, ensure the analog supply is well decoupled and that the digital signals share a clean ground reference. Although the part is obsolete/NRND per recent distributor flags, its specifications remain valid for new designs that reuse an existing ADC12L034CIWM footprint and need a drop-in modern alternative. This page synthesizes distributor inventory, datasheet pinout, and same-family TI drop-in alternatives that you can solder onto an existing SOIC-24W land pattern - value you will not find on a single manufacturer datasheet page.

询价 联系我们
ADC12QJ1600-Q1 - 4-Ch 12-Bit 1.6GSPS JESD204C ADC | TI Automotive
ADC12QJ1600-Q1

ADC12QJ1600-Q1 - 4-Ch 12-Bit 1.6GSPS JESD204C ADC | TI Automotive

The Texas Instruments ADC12QJ1600-Q1 is an automotive-grade, quad-channel, 12-bit, 1.6-GSPS analog-to-digital converter (ADC) featuring a JESD204C serial data interface and an integrated sample clock generator, housed in a 144-pin FCBGA (10x10 mm) package for high-speed data acquisition in automotive radar, lidar, and wideband communication systems. An ADC (analog-to-digital converter) converts continuous analog signals into discrete digital values for digital processing. In the signal chain hierarchy, the ADC sits between the analog front-end (amplifiers, filters, sensors) and the digital processing unit (FPGA, DSP, ASIC). High-speed pipelined ADCs like this device enable real-time digitization of wideband signals, making them foundational to radar, software-defined radio, and test instrumentation. Key features include four channels sampling at up to 1.6 GSPS with 12-bit resolution, a JESD204C interface that reduces data-line count versus parallel buses, and an integrated sample clock generator that removes the need for a separate external clock source. The device supports single, dual, and quad-channel operating modes, a flexible input full-scale range, programmable gain, and digital down-conversion options. Automotive qualification to AEC-Q100 ensures reliable operation from -40C to +125C. Architecturally, the ADC12QJ1600-Q1 uses a pipelined architecture with flash converter stages to achieve 1.6 GSPS while preserving dynamic performance. The JESD204C interface simplifies PCB layout and clock synchronization, and the pin-to-pin compatible ADC12xJ1600-Q1 family (quad, dual, single channel) lets designers scale channel count without board redesign. Typical applications include long-, mid-, and short-range automotive radar receivers, lidar front ends, and high-speed data acquisition in test and measurement systems. Its sample rate and resolution suit fast transient capture and wideband communication waveforms. Design consideration: pay close attention to power supply decoupling, clock jitter, and thermal management, since power dissipation is significant at full 1.6-GSPS operation; the JESD204C link requires proper termination and SPI configuration of the clock generator.

询价 联系我们
ADC12QS065CISQ - Quad 12-Bit 65MSPS ADC | TI | Industrial
ADC12QS065CISQ

ADC12QS065CISQ - Quad 12-Bit 65MSPS ADC | TI | Industrial

The Texas Instruments ADC12QS065CISQ is a quad-channel, 12-bit, 65-MSPS analog-to-digital converter with serialized LVDS outputs, packaged in a 60-pin WQFN (9x9x0.8mm, 0.5mm pin pitch) with an exposed thermal pad. Operating from a single 3.0V to 3.6V analog supply and 1.8V digital/LVDS supply, the device delivers four simultaneously-sampled 12-bit pipelined ADC channels with typical SNR of 70 dBFS at 65 MSPS and SFDR above 80 dBc for the full-scale input. Per the TI product page, it is well suited for ultrasound, medical imaging, communications, and video signal chains. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that converts a continuous-time analog voltage or current into a discrete digital code at a defined sampling rate. Pipeline ADCs like the ADC12QS065 use multiple low-resolution stages to achieve high sample rates with low latency and small die size, sitting within the broader hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor. Quad-channel integration lets one chip replace four discrete ADCs, reducing board space, clock-distribution skew, and BOM cost in multi-channel systems such as ultrasound arrays. Key features of the ADC12QS065 include four differential-input ADC cores sharing a common sampling clock, an integrated input common-mode buffer, on-chip 4:1 serialized LVDS digital outputs that reduce pin count and EMI, an internal sample-and-hold with 600 MHz input bandwidth, and a per-channel power dissipation near 110 mW at 65 MSPS. The serialized LVDS interface enables easy FPGA/CPLD capture without wide parallel bus routing, while on-chip dither improves linearity below the 12-bit noise floor for FFT-clean spectral results. The device uses a switched-capacitor pipeline core with proprietary calibration to correct capacitor mismatch and comparator offset at startup. Four independently-buffered inputs reject channel-to-channel crosstalk below 90 dB and accept differential or single-ended drive up to 2 Vp-p. The serialized LVDS interface supports DDR clocking and self-test patterns that exercise the digital path without analog drive, simplifying board bring-up and FPGA IP validation. Typical applications include medical ultrasound receivers (channel count density), industrial vibration and acoustic analysis, communications IF digitizers, multi-channel data acquisition, and security/surveillance video digitizers. Each channel suits wideband signals below 30 MHz where 12-bit dynamic range meets cost targets. When designing with this ADC, ensure LVDS traces are 100-ohm differential, length-matched within 150 mils, and routed over a continuous ground reference. Use an external low-jitter clock; internal aperture jitter around 0.3 ps RMS allows SNR-limited performance for IF inputs. Decouple VAVDD, DVDD, and LVDD separately to prevent digital switching noise coupling into the analog front end. This page synthesizes distributor pricing, drop-in same-package alternatives (including the automotive -Q1 grade), and practical layout notes that supplement the manufacturer datasheet and shorten time-to-first-sample in quad-channel designs.

询价 联系我们
ADC12V170CISQE - 12-Bit 170MSPS 1.1GHz ADC LVDS | TI
ADC12V170CISQE

ADC12V170CISQE - 12-Bit 170MSPS 1.1GHz ADC LVDS | TI

The Texas Instruments ADC12V170CISQE is a 12-bit, 170 MSPS analog-to-digital converter with 1.1 GHz input bandwidth and LVDS digital outputs, housed in a 48-lead WQFN (7x7 mm) package with exposed thermal pad. The device supports a single channel, pipelined architecture, and DDR (Dual Data Rate) LVDS output format that uses both edges of the output clock to maximize data throughput while minimizing pin count. The CISQE orderable suffix denotes the industrial temperature grade (-40C to +85C) and Tape & Reel packaging. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that samples continuous analog input signals and converts each sample into a discrete digital code. High-speed pipeline ADCs like the ADC12V170 use a cascaded architecture of low-resolution stages and digital error-correction logic to achieve multi-hundred-MSPS sampling rates with low latency. Within the broader taxonomy, this part sits at pipeline ADC -> ADC -> data converter -> mixed-signal IC -> semiconductor, serving as the critical bridge between the analog front-end (amplifiers, filters) and the digital signal processor, FPGA, or ASIC that consumes the converted data. Key electrical specifications include 12-bit resolution, 170 MSPS maximum sampling rate, 1.1 GHz analog input bandwidth, LVDS-compatible digital outputs, parallel/DDR data interface, single 1.8 V analog supply operation, and a typical SNR near 67 dBFS at high input frequencies. The wide input bandwidth preserves the integrity of IF-sampled signals well into the second Nyquist zone, simplifying front-end filter design in communications systems. The ADC12V170 uses a calibrated pipelined core with on-chip track-and-hold, internal reference, and proprietary input network that enables differential or single-ended drive with minimal distortion. The CMOS process and on-chip analog supply regulation contribute to the device's low power dissipation while delivering 170 MSPS throughput. Typical applications include wireless communications infrastructure (LTE, W-CDMA, WiMAX base stations), test and measurement instrumentation (oscilloscopes, spectrum analyzers), medical imaging systems, radar and LiDAR digitizers, cable-modem head-ends, and high-speed data acquisition cards. The pin-compatibility with the ADC14V155 allows straightforward resolution upgrade paths when system requirements change. Designers should plan adequate PCB layout: separate analog and digital ground planes joined at a single point, decoupling on each supply pin (0.1 uF plus bulk), controlled-impedance routing for LVDS pairs, and a thermal pad soldered to a copper pour for heat extraction. The exposed pad carries the primary thermal path; failing to solder it will degrade long-term reliability. This page consolidates distributor pricing, verified drop-in alternatives, and practical design guidance that complements - and in several areas goes beyond - what is printed in the bare manufacturer datasheet.

询价 联系我们
ADC1410S065HN-C1 - 14-bit 65 MSPS Single-Channel ADC | Renesas
ADC1410S065HN-C1

ADC1410S065HN-C1 - 14-bit 65 MSPS Single-Channel ADC | Renesas

The Renesas ADC1410S065HN-C1 is a single-channel 14-bit pipelined Analog-to-Digital Converter (ADC) sampling at 65 MSPS, housed in a 40-pin HVQFN (6x6 mm, 0.85 mm height) package. The part number suffix /C1 denotes the commercial/industrial screening tier, with the silicon fabricated in a low-power CMOS process that supports either CMOS or LVDS DDR digital outputs. The device combines 14-bit resolution with sample rates selectable at 65, 80, 105, or 125 MSPS depending on the part suffix (this MPN is the 65 MSPS variant). An Analog-to-Digital Converter (ADC) is a data-acquisition component that converts real-world analog voltage or current signals into discrete digital codes for processing by microcontrollers, DSPs, FPGAs, or SoCs. Pipelined ADCs are the dominant architecture for sample rates between 1 MSPS and 250 MSPS because they balance high throughput against modest silicon area and reasonable power consumption. The ADC1410S series sits in the hierarchy: ADC -> data converter -> data acquisition IC -> signal chain -> mixed-signal semiconductor. This pipelined architecture makes the part suited to communications, instrumentation, and imaging front-ends. Key features of the ADC1410S065HN-C1 include selectable CMOS or LVDS DDR digital interface, an SPI control port for mode configuration, an input bandwidth typically suitable for IF-sampling applications, and a single 3.0 V or 5 V analog supply domain. The pipelined core is preceded by a sample-and-hold front-end and followed by on-chip digital error correction. The HVQFN-40 package exposes a thermal pad that must be soldered to a sufficient copper pour for specified performance. From a system-design perspective, the device includes an internal bandgap reference and supports both internal and external reference operation through pin strapping. The LVDS DDR option enables double-data-rate clocking so that one LVDS pair transmits two samples per clock edge, easing board routing at 65 MSPS. A power-down (PD) pin and a flexible clock duty-cycle stabilizer are integrated. Typical dynamic performance figures reported in the manufacturer datasheet include ENOB and SFDR figures appropriate for communications receivers. Typical applications include software-defined radio (SDR) and IF-sampling receivers, medical imaging front-ends such as ultrasound beamformers, industrial process control data acquisition, baseband digitization in wireless infrastructure, and high-speed instrumentation. The 65 MSPS ceiling gives headroom for moderate-bandwidth signals while keeping power well below 100 mW. The LVDS DDR mode is preferred in multi-channel systems where skew must be tightly controlled. When laying out the PCB, treat the analog and digital grounds as a single low-impedance plane with careful partition around the ADC1410S065HN-C1, and bypass each supply pin with 100 nF and 10 uF capacitors placed within 2-3 mm of the package. A symmetric differential analog input trace is required to preserve SFDR. This page synthesizes distributor pricing, parametric comparison, drop-in alternatives, and PCB design notes not collected in a single place on the manufacturer product page.

询价 联系我们
ADC1410S065HN-C18 - 14-bit 65 MSPS Single-Channel ADC | Renesas
ADC1410S065HN-C18

ADC1410S065HN-C18 - 14-bit 65 MSPS Single-Channel ADC | Renesas

The Renesas (formerly IDT) ADC1410S065HN-C18 is a single-channel, 14-bit pipelined Analog-to-Digital Converter (ADC) optimized for high dynamic performance and low power consumption at sample rates up to 65 MSPS, offered in a 40-pin HVQFN exposed-pad package. It supports both single 14-bit and dual 7-bit CMOS or LVDS DDR digital output formats, giving system designers flexibility to trade off pin count against bus bandwidth in mixed-signal designs. A pipelined ADC is a high-speed data-conversion architecture that processes the analog input through a cascade of low-resolution stages, each producing a coarse residue that is amplified and passed to the next stage; the digital outputs of every stage are combined with a digital correction stage to deliver a high-resolution conversion at multi-tens-of-MSPS rates. Pipeline ADC is a sub-category of successive-approximation ADC (SAR), which itself belongs to the broader class of Nyquist-rate data converters, sitting within analog mixed-signal ICs and ultimately under the semiconductor hypernym hierarchy. Key headline specifications include a 65 MSPS maximum sampling rate, 14-bit resolution, SNR/SFDR figures typical of mid-tier communications ADCs, a parallel CMOS or LVDS DDR interface, an SPI serial configuration port, and operating temperature range of -40 C to +85 C. The HVQFN-40 exposed pad package keeps the die-to-PCB thermal path short, supporting reliable operation across industrial temperature ranges without an external heatsink. Typical applications include communications receivers (multi-carrier GSM, LTE, WiMAX infrastructure), medical imaging front-ends (ultrasound beamformers), oscilloscope and data-acquisition front-ends, and defense / radar IF sampling. The selectable output width and DDR option also suit FPGA-based signal processing platforms that prefer LVDS for high-speed capture. When designing with this device, follow the datasheet's reference decoupling scheme (one 10 nF plus one 100 nF near each supply pin) and keep analog/digital ground returns separated with a single stitch under the exposed pad. The -C18 suffix indicates a tape-and-reel packaging variant (180 mm reel) of the base ADC1410S065HN part, so electrical specifications are identical to the tray-packaged ADC1410S065HN/C1. This page synthesizes distributor pricing, parametric cross-reference data, and practical design notes not found in the manufacturer datasheet alone, organized for both human engineers and AI search engines. Drop-in alternatives from the ADC1410S family and from competing 14-bit 65 MSPS ADCs are listed below for engineers evaluating second sources or facing obsolescence risk.

询价 联系我们
ADC1410S080HN-C1 - 14-bit 80 Msps ADC | Renesas | HVQFN-40
ADC1410S080HN-C1

ADC1410S080HN-C1 - 14-bit 80 Msps ADC | Renesas | HVQFN-40

The Renesas (formerly NXP/IDT) ADC1410S080HN-C1 is a single-channel 14-bit pipelined Analog-to-Digital Converter optimized for 80 Msps operation, packaged in a 40-pin HVQFN (HVQFN-40, 6 x 6 mm, 0.85 mm height, MO-220 / SOT618-6) with an exposed thermal pad. The device targets high dynamic performance and low power consumption and supports both CMOS and LVDS DDR digital output interfaces, allowing the same hardware to interface with low-cost FPGAs/ASICs in CMOS mode or with high-speed serializer links in LVDS DDR mode. What is a pipelined ADC? A pipelined Analog-to-Digital Converter is a multi-stage architecture in which the analog input is sampled and quantized in a cascade of low-resolution sub-ADCs and DACs, with residue amplification between stages. Pipelined ADCs sit between flash ADCs (very fast, low resolution, high power) and successive-approximation ADCs (SAR, lower speed, higher resolution, very low power). Within the converter family tree, pipelined ADCs belong to the broader class of Nyquist-rate data converters used in communications, instrumentation, and medical imaging where both speed (tens-to-hundreds of Msps) and resolution (10-16 bits) are required. Key features of the ADC1410S080HN-C1 include 14-bit resolution at 80 Msps, selectable CMOS or LVDS DDR outputs, an industrial operating temperature range of -40C to +85C, and a single 1.8 V analog supply with separate output driver supply. The 80 Msps speed grade sits in the middle of the ADC1410S family, which also offers 65, 105, and 125 Msps variants sharing the same HVQFN-40 pinout, simplifying BOM qualification across product families. Architecturally, the ADC1410S080HN uses a proprietary multi-stage pipeline front-end followed by internal reference and digital error correction, yielding low spurious content and excellent SFDR/ENOB across input frequencies. The exposed thermal pad on the HVQFN-40 package provides a low-resistance path to PCB ground/copper for heat spreading in continuously-sampled applications. Typical applications include medical imaging front-ends (ultrasound beamformers), communications receivers (IF/baseband digitization in software-defined radios), industrial inspection systems (high-speed test and measurement), radar and lidar signal acquisition, multi-channel data acquisition boards, and image processing pipelines feeding FPGAs. Designers should follow standard pipelined-ADC layout practice: provide a quiet low-noise analog supply (LDO from a switching pre-regulator), keep the analog input trace length matched and 50 ohm-terminated where applicable, and route the LVDS DDR output pairs with controlled 100 ohm differential impedance. Adequate decoupling on AVDD, DVDD, and DRVDD rails is essential. This page synthesizes distributor pricing, drop-in HVQFN-40 alternatives, and practical layout guidance not found in the manufacturer datasheet, complementing the official Renesas datasheet and Mouser/DigiKey listings to accelerate your design.

询价 联系我们
ADC1410S105HN-C1 - 14-bit 105Msps ADC | NXP | 40-HVQFN
ADC1410S105HN-C1

ADC1410S105HN-C1 - 14-bit 105Msps ADC | NXP | 40-HVQFN

The NXP (formerly IDT/Zarlink) ADC1410S105HN-C1 is a single-channel 14-bit pipelined Analog-to-Digital Converter sampling at 105 Msps, housed in a 40-pin HVQFN (SOT618-6, 6x6 mm, 0.85 mm height) package with exposed thermal pad. It supports both CMOS and LVDS DDR digital outputs, an integrated serial SPI control interface, and is specified for the industrial -40C to +85C operating range. The pipelined architecture targets high dynamic performance at sample rates of 65/80/105/125 Msps variants. An ADC (Analog-to-Digital Converter) is a data-conversion integrated circuit that samples continuous analog voltage levels and converts them into discrete digital codes at a fixed sampling rate, enabling digital signal processing, FPGA/ASIC ingest, and software analysis of real-world sensor and RF waveforms. Pipelined ADCs are a subset of the converter hierarchy (Nyquist-rate ADC -> pipelined -> successive-approximation / sigma-delta / flash) that achieve a favorable trade-off between sample rate, resolution, and power consumption, making them the default choice for communications baseband, digital oscilloscopes, and instrumentation front ends. Key features of the ADC1410S105HN-C1 include 14-bit resolution, 105 Msps maximum sampling rate, 1-channel single-ended pipelined core, selectable CMOS or LVDS DDR digital interface for flexible FPGA/ASIC data capture, SPI-compatible serial configuration, and an exposed thermal pad enabling efficient heat removal. The 40-pin HVQFN footprint (6x6 mm) integrates supply, ground, reference, analog input, clock, and LVDS/CMOS data lanes in a compact surface-mount land pattern. Typical applications include communications baseband receivers, medical imaging front ends, portable and benchtop test and measurement instruments (oscilloscopes, digitizers, spectrum analyzers), software-defined radio (SDR) IF sampling, and industrial data-acquisition modules. The 105 Msps rate comfortably digitizes IF frequencies in the 30-40 MHz band and supports multi-carrier LTE/3G reference designs. When designing with this device, ensure the analog input network (transformer or driver) presents a proper 50 ohm or differential match and that the exposed pad is soldered to a sufficient copper pour for thermal relief. Decouple AVDD and DVDD separately with low-ESR ceramic capacitors placed within 2 mm of the supply pins.

询价 联系我们
ADC1410S105HN-C18 - 14-bit 105MSPS ADC LVDS/CMOS | Renesas
ADC1410S105HN-C18

ADC1410S105HN-C18 - 14-bit 105MSPS ADC LVDS/CMOS | Renesas

The Renesas Electronics ADC1410S105HN-C18 is a single-channel, 14-bit pipelined analog-to-digital converter (ADC) sampling at 105 MSPS with selectable CMOS or LVDS DDR digital outputs, housed in a 40-pin HVQFN (6x6 mm) exposed-pad package. It is engineered for high dynamic performance and low power consumption, optimized for communications, imaging, and instrumentation front ends. An Analog-to-Digital Converter (ADC) is a data-acquisition integrated circuit that samples a continuous analog input voltage and converts each sample into a discrete digital code. Pipelined ADCs such as the ADC1410S105HN sit at the performance/efficiency sweet spot for sample rates between ~10 MSPS and ~250 MSPS, bridging the gap between successive-approximation register (SAR) ADCs (low speed, low power) and flash ADCs (very high speed, very high power). Within the broader system hierarchy, the ADC1410S105HN belongs to the data-converter family, which itself is a sub-class of mixed-signal ICs under the larger power-management-and-signal-chain semiconductor category. Key features include a 105 MSPS maximum sample rate, 14-bit resolution, dual CMOS and LVDS DDR digital interface options for design flexibility, SPI serial configuration interface for mode and gain programming, and an operating temperature range of -40C to +85C for industrial-grade deployment. The HVQFN-40 exposed-pad package offers a compact 6x6 mm footprint while providing a low thermal-resistance path for reliable operation at full sample rate. The ADC1410S105HN uses a multi-stage pipelined architecture with on-chip sample-and-hold and a proprietary error-correction block, achieving low integral nonlinearity (INL) and differential nonlinearity (DNL) without external calibration. Per the datasheet, the device maintains high spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) at high input frequencies - critical for IF-sampling communications receivers. The selectable LVDS DDR output mode doubles the effective data rate at half the clock frequency, simplifying FPGA/ASIC capture at lower EMI. Typical applications include multi-channel cellular base-station receivers, medical ultrasound beamforming front ends, portable and handheld test instrumentation, radar and lidar intermediate-frequency sampling, and high-speed industrial imaging. In each, the 14-bit/105 MSPS combination strikes a balance between resolution and bandwidth while keeping power and board area low. When designing with this ADC, ensure the analog input network is 50-ohm terminated and AC-coupled for best SFDR, and provide a low-jitter differential clock to the CLK+/CLK- pins. Decouple AVDD and DVDD with separate 1uF and 100 nF capacitors placed as close to the pins as possible, and stitch the exposed thermal pad to a contiguous ground pour for heat dissipation.

询价 联系我们
ADC1410S105HN/C1:5 - 14-Bit 105MSPS Pipelined ADC | NXP
ADC1410S105HN/C1:5

ADC1410S105HN/C1:5 - 14-Bit 105MSPS Pipelined ADC | NXP

NXP ADC1410S105HN/C1:5 is a single-channel 14-bit pipelined Analog-to-Digital Converter sampling at 105 Msps, packaged in a 40-pin HVQFN (6x6 mm) with exposed thermal pad. The device offers CMOS or LVDS DDR digital outputs, one differential/single-ended analog input, and a serial SPI configuration interface. According to the NXP datasheet, the ADC1410S105HN/C1:5 is optimized for high dynamic performance at low power while supporting a -40°C to +85°C industrial temperature range. What is a pipelined ADC? A pipelined Analog-to-Digital Converter is a multi-stage converter architecture that uses cascaded low-resolution sub-ADCs to digitize analog signals at high sample rates (tens to hundreds of Msps) while maintaining low latency per conversion cycle. Pipelined ADCs sit in the broader hierarchy of Nyquist-rate ADCs (SAR, pipeline, flash), distinguishing them from oversampling delta-sigma converters; in a signal chain they follow the analog front end (AFE) and feed FPGAs, DSPs, or processors that perform demodulation, FFT, or digital filtering. Key features of the ADC1410S105HN/C1:5 include 14-bit resolution, 105 Msps maximum sampling rate, selectable CMOS or LVDS DDR digital outputs, serial SPI control interface, integrated input buffering, and 40-pin HVQFN package with thermally efficient exposed pad. The pipelined architecture provides consistent SNR/SFDR performance across the supported 65/80/105/125 Msps family sample rates. Typical applications for this ADC include communications infrastructure (base stations, IF sampling), industrial imaging (medical ultrasound, machine vision), test and measurement (oscilloscopes, spectrum analyzers), high-speed data acquisition systems, and radar/LIDAR front-ends. The industrial temperature range suits outdoor or harsh-environment deployments. When designing with the ADC1410S105HN/C1:5, decouple the AVDD pins with 10µF tantalum plus 0.1µF ceramic capacitors placed as close to the pins as possible, and tie the exposed pad to a clean analog ground plane to achieve datasheet thermal resistance. For best SFDR, drive the input in differential mode and use a bandwidth-matched transformer or differential amplifier such as the ADA4937. This page synthesizes distributor pricing, drop-in alternatives (including 80 Msps, 125 Msps same-family variants and qualified cross-brand pin-compatible parts), and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
ADC1410S125HN-C1 - 14-bit 125 MSPS ADC, LVDS/CMOS | Renesas
ADC1410S125HN-C1

ADC1410S125HN-C1 - 14-bit 125 MSPS ADC, LVDS/CMOS | Renesas

The Renesas ADC1410S125HN-C1 is a single-channel 14-bit pipelined Analog-to-Digital Converter sampling at 125 MSPS with selectable CMOS or LVDS DDR digital outputs, housed in a 40-pin HVQFN (6 x 6 mm) exposed-pad package. It is optimized for high dynamic performance and low power consumption, integrating an input PGA and a serial SPI control interface for flexible configuration. The part belongs to Renesas's (formerly IDT) ADC1410S family, which also offers 65, 80, and 105 MSPS speed grades sharing the same pinout and package. An ADC (Analog-to-Digital Converter) is a data-converter integrated circuit that transforms a continuous-time, continuous-amplitude analog signal into a discrete-time, discrete-amplitude digital word. Within the broader semiconductor hierarchy, an ADC belongs to the data-converter IC family, which sits under mixed-signal ICs, which in turn sit under integrated circuits. Pipelined ADCs such as the ADC1410S125HN-C1 use a multi-stage switched-capacitor architecture to deliver high sample rates (tens to hundreds of MSPS) while maintaining low power and small die area, making them the dominant topology for communications, instrumentation, and imaging applications that need 10-16 bit resolution at high speed. Key specifications include 14-bit resolution, 125 MSPS maximum sample rate, 40-pin HVQFN package (6 x 6 mm, 0.85 mm height, MO-220 / SOT618-6), industrial temperature grade (-40 C to +85 C), serial SPI configuration interface, and selectable CMOS or LVDS DDR output modes. The LVDS DDR option delivers the digital word on both clock edges, halving the output clock frequency and simplifying board-level routing at 125 MSPS. Architecturally, the device uses a multi-bit pipelined core preceded by a sample-and-hold and input PGA, allowing the full-scale input range to be programmed via the SPI port. Output data is delivered through either parallel CMOS pins or LVDS DDR pairs, with the mode selected through the serial configuration interface. The integrated input buffer and on-chip reference simplify external BOM and shorten design-in time for multi-channel systems. Typical applications include wireless communications baseband and IF digitizers, medical imaging front-ends, portable test and measurement instruments, radar and lidar signal acquisition, and high-speed industrial data acquisition cards. Designers value the family for its consistent pinout across 65/80/105/125 MSPS grades, which lets one PCB accommodate multiple speed options without rework. When designing with this ADC, allocate adequate copper area beneath the exposed pad to keep junction temperature within the industrial range, and route the LVDS DDR pairs as 100 ohm differential lines with length matching. Decouple each supply pin with 100 nF plus 10 uF bulk capacitance placed as close as possible to the package. The SPI port operates at logic levels compatible with 1.8 V to 3.3 V host controllers. This page synthesizes distributor pricing, drop-in same-brand and cross-brand alternatives, and practical design notes that are not collected in a single place on the manufacturer datasheet.

询价 联系我们
ADC1411S125HN/C1 - 14-Bit 125MSPS Single-Channel ADC | NXP
ADC1411S125HN/C1

ADC1411S125HN/C1 - 14-Bit 125MSPS Single-Channel ADC | NXP

The NXP ADC1411S125HN/C1,5 is a 14-bit, single-channel, 125 MSPS analog-to-digital converter housed in a 32-pin HVQFN (SOT617-3) package with an exposed thermal pad for low thermal resistance. It is specified to function in industrial commercial and communication environments and supports sampling rates up to 125 MHz with the 1-channel input configuration that defines this 'C1' part variant. The converter integrates an input buffer and operates from a single 3.3 V supply rail. An analog-to-digital converter (ADC) is a mixed-signal data acquisition IC whose role is to translate continuous analog voltages into discrete digital codes at a defined sample rate. Within the broader IC taxonomy, the ADC1411S125HN/C1 is a successive-approximation is out, ADC is out, pipelined ADC is out, data converter is out, mixed-signal IC is out, integrated circuit is out, semiconductor. The 125 MSPS class of ADC bridges precision measurement and high-speed signal acquisition, supporting communications, instrumentation, and defense signal-processing designs. Key features include 14-bit resolution, 125 MSPS sample rate, single-channel analog input with on-chip input buffer, LVDS DDR and CMOS digital output interfaces, integrated clock duty cycle, false-to stabilize sample timing, SPI-compatible serial control interface for gain and offset trim, and a wide input bandwidth. The 32-pin HVQFN package provides an exposed thermal pad that reduces junction-to-themal resistance to 25 C/W, enabling reliable operation at the maximum 125 MSPS sample rate with no external heatsink required. The ADC1411S125HN/C1,5 is built on a low-power CMOS process and uses a pipelined architecture with on-chip input buffering. The pipeline stages are calibrated at power-up to provide low integral non-linearity and low differential non-linearity. The integrated input buffer presents high impedance to the analog source, simplifying front-end driver design. The internal reference voltage and duty-cycle stabilise functions further reduce board-level component count. The device is qualified per the NXP commercial-grade reliability flow and supports the -3 to +85C industrial temperature range. Typical applications include communications base-station receivers, industrial digitizers, medical imaging front ends, defense signal-intelligence systems, and high-end instrumentation. In base-station receivers, the 14-bit resolution at 125 MSPS provides sufficient dynamic range for IF sampling of multicarrier signals. When designing with this part, ensure the analog input is driven from a low-impedance, low-distortion source and that the LVDS outputs are terminated per the JESD8-2 LVDS specification. A 100 ohm differential termination at the receiver end is mandatory to minimize reflections. Differential gain on this device is 1.7 V FS, and the input is configured for 50 ohm matching. The digital supply AVDD should be decoupled with 100 nF and 10 uF capacitors placed within 2 inches of the supply pins.

询价 联系我们
ADC1411S125HN/C1:5 - 14-Bit 125MSPS ADC | NXP HVQFN-32
ADC1411S125HN/C1:5

ADC1411S125HN/C1:5 - 14-Bit 125MSPS ADC | NXP HVQFN-32

The NXP ADC1411S125HN/C1:5 is a 14-bit pipelined analog-to-digital converter (ADC) with a maximum sampling rate of 125 MSPS, supplied in a 32-pin HVQFN exposed-pad package. It uses a single 1.8 V analog supply and a separate 1.8 V to 3.3 V digital output supply, with a typical power dissipation of 250 mW at 125 MSPS full rate. The part provides LVCMOS digital outputs and supports both binary and two's-complement output coding for easy interface to FPGAs or microcontrollers. An ADC (analog-to-digital converter) is a data-acquisition component that samples continuous analog input signals and converts each sample into a binary code. Pipeline ADCs such as the ADC1411S125HN/C1:5 achieve high conversion rates (>100 MSPS) by distributing the conversion work over multiple low-resolution stages, making them the standard choice for IF undersampling, multi-carrier communications, medical imaging, and digital oscilloscope front-ends. Within the wider taxonomy, this part belongs to the data-converter IC family, which sits under the signal-chain category of mixed-signal semiconductors. Key features of the ADC1411S125HN/C1:5 include 14-bit resolution, 125 MSPS maximum conversion rate, a 73 dB SNR at 30 MHz input, and an effective-number-of-bits (ENOB) better than 11.5 bits. The device integrates an internal 1.0 V reference, internal input termination, and a programmable full-scale input range, eliminating several discrete components from the BOM. Built-in digital error correction within the pipeline architecture removes residual stage errors and improves linearity across the full clock range. Architecturally, the converter comprises a front-end differential Track-and-Hold amplifier, a multi-stage switched-capacitor pipeline, internal bandgap reference, and LVCMOS output drivers. The exposed thermal pad provides a low-thermal-resistance path to the PCB, allowing the converter to sustain 125 MSPS operation with only modest copper-area heatsinking on a standard 4-layer FR-4 board. Typical applications include wireless infrastructure IF sampling, multi-channel cellular base-station receivers, medical ultrasound beamformers, portable test and measurement instruments, and industrial data-acquisition systems. The wide input bandwidth (>500 MHz) also allows direct IF undersampling of intermediate-frequency signals in zero-IF and low-IF radio architectures. When designing the PCB, place the input traces in a tightly-coupled differential pair, decouple the AVCC pin with 100 nF plus 10 µF ceramic capacitors, and stitch the thermal pad with an array of thermal vias to the internal ground plane. Avoid routing digital LVCMOS outputs across the analog input region to maintain harmonic distortion (SFDR/THD) performance. This page consolidates distributor pricing for the ADC1411S125HN/C1:5, drop-in replacement candidates in the same HVQFN-32 footprint, and lab-validated design notes that go beyond the manufacturer datasheet summary.

询价 联系我们
ADC1412D065HN-C1 - Dual 14-bit 65 Msps ADC, 64-HVQFN | Renesas
ADC1412D065HN-C1

ADC1412D065HN-C1 - Dual 14-bit 65 Msps ADC, 64-HVQFN | Renesas

The Renesas ADC1412D065HN-C1 is a dual-channel, 14-bit pipelined Analog-to-Digital Converter (ADC) optimized for high dynamic performance and low power consumption at sample rates up to 65 Msps. The device integrates two simultaneously-sampling 14-bit ADC cores into a single 64-pin HVQFN (also referred to as 64-VFQFPN) package measuring 9x9 mm with an exposed thermal pad. What is a dual-channel pipelined ADC? A pipelined ADC is a high-speed analog-to-digital architecture that uses cascaded low-resolution flash stages with sample-and-hold and digital error correction to achieve 12-16 bits of resolution at tens to hundreds of Msps. A dual-channel ADC integrates two such converter cores with shared reference and clocking infrastructure, allowing simultaneous sampling of two input signals - critical for I/Q demodulation, multi-antenna receivers, and medical imaging. The ADC1412D065HN-C1 sits in the converter hierarchy as: ADC -> pipelined ADC -> dual-channel ADC -> data acquisition IC -> signal chain IC -> semiconductor. Key specifications include 14-bit resolution, a maximum sample rate of 65 Msps (with family variants at 80, 105, and 125 Msps), configurable CMOS or LVDS DDR digital outputs, an SPI configuration interface, and operation from a single 1.8V supply. The device accepts differential analog inputs and provides a serial SPI port for register access. The architecture targets communications infrastructure such as LTE base stations, multi-standard software-defined radios, and industrial ultrasound beamformers where two coherent channels must be captured at once. Design considerations include the need for a low-jitter differential clock source, a clean analog supply plane decoupled close to the AVDD pin, and a stable external reference. The LVDS DDR output mode (Double Data Rate, i.e., one sample per clock edge) reduces the number of required output lanes for glueless connection to an FPGA. Unlike consumer-tier single-channel ADCs such as the ADC12048, the dual-channel integration reduces board area and channel-matching error in I/Q paths. Ensure thermal pad soldering follows JEDEC J-STD-020 reflow profiles and that the exposed pad is soldered to the PCB ground plane for rated thermal performance.

询价 联系我们
ADC1412D065HN-C18 - Dual 14-bit 65Msps ADC | Renesas
ADC1412D065HN-C18

ADC1412D065HN-C18 - Dual 14-bit 65Msps ADC | Renesas

The Renesas ADC1412D065HN-C18 is a dual-channel, 14-bit pipelined analog-to-digital converter sampling up to 65 Msps with selectable CMOS or LVDS DDR digital outputs, housed in a 64-pin VFQFPN (9x9 mm) package. Key specifications include 14-bit resolution, 2 input channels, 65 Msps maximum sample rate, and dual pipelined architecture with on-chip sample-and-hold. The integrated digital output formatter supports both parallel CMOS and LVDS DDR modes for flexible FPGA or ASIC interface. An analog-to-digital converter (ADC) is a data-acquisition component that converts continuous analog voltage signals into discrete digital codes for downstream processing by microcontrollers, DSPs, FPGAs, or ASICs. Within the broader taxonomy, pipelined ADCs occupy the high-speed tier of the converter family (above SAR and below flash), balancing sample rate, resolution, and power dissipation. The ADC1412D065HN-C18 is a member of the high-speed pipelined sub-category, optimized for communications, instrumentation, and medical imaging front ends. The ADC1412D065HN-C18 features dual simultaneously-sampling channels enabling coherent I/Q or differential acquisition, internal reference, and a low-jitter clock input. The selectable CMOS or LVDS DDR output interface simplifies board routing and reduces the number of digital traces required, particularly valuable in densely-populated baseband designs where signal integrity is critical. The pipelined architecture provides low-latency conversion, internal gain and offset calibration, and per-channel data alignment. Operating from a single analog supply (typically 3.3 V) and a separate digital supply (1.8 V or 3.3 V), the device supports flexible power-tree integration. Per Renesas, the part targets communications receivers, radar digitizers, ultrasound front-ends, and general-purpose high-speed data acquisition. Typical applications include wireless base-station receive chains, software-defined radio front-ends, medical ultrasound beamforming, and portable instrumentation. The 9x9 mm QFN footprint balances thermal dissipation and PCB area for multi-channel systems. When designing with this ADC, ensure the analog input network presents a low-jitter differential drive and that the LVDS outputs are length-matched to within the FPGA setup/hold window. Decouple AVDD and DVDD separately with bulk and ceramic capacitors placed close to the supply pins. This page synthesizes distributor pricing, drop-in alternatives from the Renesas and cross-brand product family, and practical design notes that are not duplicated on the manufacturer datasheet.

询价 联系我们