产品(39,000+)

H9JCNNNBK3MLYR-N6E-SK - 16Gb LPDDR5-6400 SDRAM | SK Hynix | TFBGA-315
H9JCNNNBK3MLYR-N6E-SK

H9JCNNNBK3MLYR-N6E-SK - 16Gb LPDDR5-6400 SDRAM | SK Hynix | TFBGA-315

The SK Hynix H9JCNNNBK3MLYR-N6E-SK is a 16 Gigabit LPDDR5-6400 SDRAM organized as 512M x 32 in a 315-ball TFBGA surface-mount package, delivering up to 6400 Mbps per pin data rate over a 16-bit data bus. Operating from a 1.05 V core supply (rail range 1.01 V to 1.12 V) with a 1.7 V to 1.95 V supply for the I/O, it is engineered for high-bandwidth, power-sensitive mobile and embedded platforms. LPDDR5 (Low-Power Double Data Rate 5) SDRAM is a JEDEC-defined volatile memory standard designed as the successor to LPDDR4/4X for smartphones, tablets, ultra-thin notebooks, AI edge devices, and automotive infotainment. It belongs to the SDRAM -> DRAM -> volatile memory -> memory IC hierarchy. Compared with LPDDR4X, LPDDR5 doubles peak bandwidth to 6400 Mbps, introduces lower VDD voltages for energy efficiency, and adds on-die ECC and Decision Feedback Equalization (DFE) for signal integrity at high speeds. Key differentiating parameters include the 6400 Mbps data rate, 16-bit bus width, four-channel internal architecture, 1.05 V VDDQ, and an operating temperature range of -55C to +125C (industrial-grade, the widest grade in the H9JCNNN family). The device supports deep-sleep and power-down modes for sub-mW standby current. The 315-ball TFBGA package provides a low-profile footprint suitable for height-constrained mobile designs. The architecture is built on SK Hynix's advanced 1y-nm DRAM process, integrating the PMIC interface commands, frequency set, and refresh management defined by JEDEC JESD209-5. The dual-channel configuration enables parallel access for application processors, AI accelerators, and GPUs sharing the same memory pool. Built-in ECC mitigates single-bit soft errors at sub-20 nm nodes. Typical applications include flagship smartphone main memory, AI edge inference modules, ultra-thin notebook DRAM, automotive infotainment and ADAS platforms, and high-bandwidth industrial controllers. It pairs naturally with Snapdragon 8-series, MediaTek Dimensity, and Apple A-series application processors that natively support LPDDR5-6400 interfaces. Designers must route the 16-bit data bus as length-matched differential pairs with controlled impedance (typically 85 ohm differential), place a 0.1 uF + 1 uF decoupling capacitor network near each VDD/VDDQ ball, and follow SK Hynix reference PCB layout for the 315-ball TFBGA land pattern. The -SK suffix indicates SK Hynix branded reel/tray packaging. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, providing engineering value beyond simple spec repetition.

询价 联系我们
HA4-5002/883 - 110MHz Wideband Buffer Amplifier | Renesas
HA4-5002/883

HA4-5002/883 - 110MHz Wideband Buffer Amplifier | Renesas

The Renesas HA4-5002/883 is a monolithic, wideband, high slew rate, high output current buffer amplifier, qualified to MIL-STD-883 and housed in a 20-pin CLCC surface-mount package. It utilizes Intersil (formerly Harris) Dielectric Isolation technology to deliver 110 MHz of bandwidth, a typical slew rate of 1300 V/µs (1000 V/µs minimum), and a ±100 mA minimum output current capability enhanced by a 3 Ω output impedance. The 20-CLCC ceramic package makes it suitable for high-reliability military and aerospace programs that require hermetic packaging. A buffer amplifier (also called a unity-gain follower or current buffer) is a special-purpose analog building block placed between a high-impedance source and a low-impedance load. Buffers provide current gain without voltage gain, isolating upstream stages from load-induced disturbances such as cable capacitance, ADC input charge kickback, or laser diode nonlinear loading. In the broader taxonomy, the HA-5002 sits in the signal-chain hierarchy: sensor/transducer -> buffer -> ADC or driver -> downstream load. Buffer amplifiers complement operational amplifiers, which typically cannot source/sink the high peak currents needed for fast-settling, high-capacitance applications. Key features of the HA4-5002/883 include wideband 110 MHz operation, 1300 V/µs typical slew rate, ±100 mA minimum output current, 3 Ω output impedance, dielectric-isolation process for low parasitic latch-up susceptibility, and MIL-STD-883 Class B processing for high-reliability environments. The combination of speed and output drive makes it a classic choice for driving analog signals through long cables, laser diodes, and high-capacitance loads. Internally, the HA-5002 uses a complementary bipolar output stage with dielectric isolation, which prevents the substrate-junction latch-up common in junction-isolated high-current buffers. The wideband design uses local feedback and feedforward compensation paths that allow the closed-loop buffer to maintain flat gain and low distortion well past 10 MHz, even when driving 50 Ω or 100 Ω transmission lines. Typical applications include coaxial cable drivers, ADC front-end buffers, laser diode drivers, video line drivers, ATE (automatic test equipment) pin electronics, and reference buffers in precision instrumentation. Its MIL-STD-883 qualification also makes it suitable for avionics, missile guidance, and space-grade subsystems where commercial-grade plastic op amps are unacceptable. When designing with the HA4-5002/883, observe the thermal limitations of the 20-CLCC package: continuous ±100 mA output into a low impedance load produces noticeable self-heating, and supply bypassing must be placed immediately at the supply pins to sustain the high slew rate without ringing. This page synthesizes distributor pricing, drop-in and pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone, helping procurement and design engineers quickly evaluate the HA4-5002/883 for new designs and legacy sustainment.

询价 联系我们
HC32L031 - 48MHz Cortex-M0+ 64KB Flash MCU | XHSC (小华)
HC32L031

HC32L031 - 48MHz Cortex-M0+ 64KB Flash MCU | XHSC (小华)

The XHSC (小华半导体) HC32L031 is a 32-bit ultra-low-power microcontroller based on the Arm Cortex-M0+ core running up to 48 MHz, integrating 64 KB of Flash and 8 KB of SRAM in compact LQFP-32 and QFN-32 (4x4 mm) packages. It operates from a wide 1.8 V to 5.5 V supply, making it suitable for both battery-powered and industrial 5 V rails. A low-dropout (LDO) linear regulator is an analog integrated circuit that maintains a tightly regulated output voltage even when the input-to-output voltage difference is small (the dropout voltage). LDOs belong to the broader family of linear regulators, which in turn are a subset of voltage regulators and power management ICs used in virtually every powered electronic system. The HC32L031 sits one level above: it is a microcontroller that *uses* internal LDOs to power its core and analog domains from a single external supply. Key differentiating features include a deeply engineered power management system with 0.65 µA Deep-Sleep current (all clocks off, IO retention, IO interrupt wake-up, full RAM/CPU state retention) and 45 µA/MHz active current at 3 V / 48 MHz with peripherals off. The device includes multiple low-power modes, an integrated LDO regulator, and Brown-Out Reset (BOR). Peripheral highlights include a 12-bit SAR ADC, multiple timers, UART, SPI, I²C, and an integrated LCD segment driver (variant dependent), making it highly competitive in metering and HMI applications. Architecturally, the HC32L031 leverages the Cortex-M0+ core (Thumb-2 instruction set, single-cycle IO) and pairs it with a high-efficiency on-chip voltage regulator to minimize dynamic power. The Flash is organized with erase/write protection to support secure in-field firmware updates. Typical applications include battery-powered IoT sensors, smart water/gas/heat meters, wearable health devices, low-power wireless sensor nodes, BLE/Zigbee beacon peripherals, electronic shelf labels, and consumer appliances requiring always-on sensing with multi-year battery life. Its wide 1.8 V–5.5 V input range also suits industrial 5 V control boards. When designing with the HC32L031, select the package variant (LQFP-32 F8TB or QFN-32 F8UB) that matches your PCB footprint and thermal target. Pay attention to decoupling: place 100 nF + 4.7 µF ceramic capacitors close to VDD/VSS pins to keep the internal LDO stable during load transients. This page synthesizes distributor pricing, package variants, drop-in alternatives, and practical design notes not consolidated in any single manufacturer datasheet, providing actionable engineering value for selection and procurement.

询价 联系我们
HCF4046M013TR - Micropower PLL, 1.4MHz, SOIC-16 | STMicroelectronics
HCF4046M013TR

HCF4046M013TR - Micropower PLL, 1.4MHz, SOIC-16 | STMicroelectronics

The STMicroelectronics HCF4046M013TR is a Micropower Phase-Locked Loop (PLL) IC operating at up to 1.4 MHz, housed in a 16-pin SOIC (0.154", 3.90mm width) package. It features quiescent current specified to 20V, very low power consumption of 70 µW (typ.) at VCO = 5V, and operating frequency range to 1.4 MHz (typ.) at VDD = 10V. The device also includes low frequency drift of 0.04%/°C (typ.) at VDD = 10V and a choice of two phase comparators: an exclusive-OR (XOR) detector and an edge-triggered sequential phase detector with charge pump output. A Phase-Locked Loop (PLL) is a closed-loop feedback system that generates an output signal whose phase is locked to the phase of an input reference signal. PLLs are widely used for frequency synthesis, modulation/demodulation, clock recovery, and tone decoding in analog and mixed-signal systems. As a member of the CMOS 4000-series logic family, the HCF4046 sits within the broader hierarchy of clock and timing integrated circuits (ICs), which also include phase-locked loops, frequency synthesizers, and clock generators. The 4046 architecture in particular is the industry-standard micropower PLL, with variants offered by multiple manufacturers. Key features of the HCF4046M013TR include a wide supply voltage range of 3V to 20V, very low quiescent current well-suited for battery-powered designs, two selectable phase comparators (Phase Comparator I for low-noise locking without dead zone, Phase Comparator II for high-noise rejection with a charge-pump output capable of driving low-pass filters), an on-chip linear VCO with external R/C tuning, and source-follower output buffer. The combination of low power, wide supply range, and dual phase comparators makes the device uniquely flexible among monolithic PLL ICs. The HCF4046 employs a CMOS architecture with an internal VCO whose gain is set by external resistor R1 and capacitor C1, and whose frequency offset is set by external R2 and C2. Phase Comparator I is an exclusive-OR gate offering low harmonic content in the locked condition but requiring 90° phase offset at the VCO input. Phase Comparator II is an edge-triggered sequential network that locks at zero phase error, allowing the loop to operate with arbitrary input duty cycles and providing a charge-pump output for direct connection to an external low-pass filter. The micropower CMOS design keeps dynamic supply current low even at maximum VCO frequency. Typical applications include FM demodulation and modulation, frequency synthesis, tone decoding, FSK (Frequency-Shift Keying) modems, motor speed control, and clock recovery from NRZ data. The wide supply range (3V to 20V) allows the device to operate directly from battery stacks, 5V logic rails, and ±15V analog supply rails with a single part number. When designing with the HCF4046M013TR, pay close attention to the loop-filter component selection, as it directly determines loop bandwidth, capture range, and lock time. Phase Comparator I requires 50% duty cycle signals for proper operation, whereas Phase Comparator II can handle any duty cycle. Bypass VDD with a 0.1 µF ceramic capacitor placed close to the IC pins to ensure clean supply rails. This page consolidates distributor pricing, verified pin-compatible drop-in alternatives, and practical loop-filter design guidance drawn from multiple sources rather than from the manufacturer datasheet alone.

询价 联系我们
HCF4093BE - Quad 2-Input NAND Schmitt Trigger | STMicroelectronics
HCF4093BE

HCF4093BE - Quad 2-Input NAND Schmitt Trigger | STMicroelectronics

The STMicroelectronics HCF4093BE is a CMOS quad 2-input NAND gate with Schmitt-trigger inputs, supplied in a 14-pin PDIP through-hole package. Each of the four independent gates performs the NAND function while exhibiting Schmitt-trigger hysteresis on both inputs, allowing slow or noisy edges to be cleaned into sharp, jitter-free logic transitions. The Schmitt trigger is a comparator-style input stage with two distinct switching thresholds: a higher positive-going threshold (VP) and a lower negative-going threshold (VN). The difference between them (VH = VP - VN) is defined as the hysteresis voltage. This built-in hysteresis makes the part ideal for conditioning slow analog or mechanical signals (RC oscillators, switch debouncing, sensor pulses) directly into clean logic levels without external comparators. The HCF4093 belongs to the 4000-series CMOS logic family, characterized by wide supply operation from 3 V to 18 V, low quiescent power consumption, and high noise immunity. Its four gates share common VDD and VSS pins. Each input is a standard CMOS inverter-style stage feeding a NAND tree, and outputs are buffered totem-pole drivers capable of sourcing/sinking typical 4000-series currents. As a CMOS part, all inputs include ESD-protection networks and should not be left floating. Typical applications include waveform and pulse shaping, monostable and astable multivibrators, line receivers for noisy environments, simple RC and crystal oscillators, and debounce circuits for mechanical switches. Hysteresis prevents multiple triggering on bouncing or slowly rising edges, eliminating the need for external Schmitt-trigger comparator stages. When designing with this device, observe standard CMOS handling: tie unused inputs to VDD or VSS (never leave them open) and place a 0.1 uF decoupling capacitor as close as possible to the VDD pin. Output drive capability is moderate (a few mA), so check fan-out when driving multiple loads or long traces.

询价 联系我们
HCS361-I/P - KEELOQ Code Hopping Encoder, 8-PDIP | Microchip
HCS361-I/P

HCS361-I/P - KEELOQ Code Hopping Encoder, 8-PDIP | Microchip

The Microchip Technology HCS361-I/P is a code hopping encoder that pairs a 28-/32-bit programmable serial number with a 64-bit programmable encryption key to produce a 67-bit transmission frame (32-bit hopping code + 35-bit fixed code) for unidirectional Remote Keyless Entry (RKE) and access-control systems. Packaged in an 8-pin PDIP through-hole outline and rated for operation from 2.0 V to 6.6 V (per Microchip datasheet) or 3.0 V to 6.9 V (per some distributor listings), it ships as a -40 °C to +85 °C industrial-grade part with the “-I” temperature suffix and the “/P” PDIP package suffix. A code hopping encoder is a security-focused transmitter IC that transmits a different encrypted code on every button press, defeating simple replay attacks. It belongs to the broader category of encoders/decoders/multiplexers (logic ICs), and within Microchip's portfolio it is a member of the KEELOQ family — a hierarchy that runs encoder -> KEELOQ hopping encoder -> security transmitter IC -> logic IC -> integrated circuit. The HCS361 sits between the lower-cost HCS300/HCS301 and newer HCS362/HCS365 devices, balancing small package outline, low BOM cost, and patented hopping-code security. Key features include 28/32-bit serial number programming, 64-bit encryption key storage in EEPROM, unique 67-bit transmission per button event, three button inputs (S0/S1/S2), a 4-word (S0..S3 with PWM) option (per family datasheet), low standby current for battery-powered fobs, automatic code-word synchronization, and Microchip's patented KEELOQ learning algorithm so a paired receiver only needs to remember the last transmitted code. HCS361-I/P is the industrial temperature (-40 °C to +85 °C) variant in the through-hole PDIP-8 footprint. The device uses Microchip's KEELOQ nonlinear block-cipher algorithm with a 64-bit manufacturer key and a 16/20-bit discriminator. On every button press the encoder generates a fresh 32-bit hopping code by combining the counter value, the button bitmap, and the encrypted discriminator; the receiver validates the rolling counter and decrypts the discriminator before accepting the transmission, providing strong replay-attack immunity for garage-door openers, gate controls, alarm panels, and automotive RKE. Typical applications include garage-door and gate openers, automotive Remote Keyless Entry transmitters, wireless doorbells, alarm and security system keypads, asset-tracking fobs, and industrial access-control handheld remotes. Pair it with a Microchip HCS compatible receiver decoder (e.g., the receiver side of the HCS family) to complete a one-way secure link. When designing with the HCS361-I/P, observe the VDD decoupling guidance from the datasheet (a 0.1 µF ceramic cap close to the VDD pin), the RF section layout for the companion transmitter PCB, and the four-button debounce pattern in Microchip application notes. The industrial -40 °C to +85 °C range makes this part suitable for outdoor fobs and unheated enclosures, while the through-hole PDIP-8 package simplifies hand-soldering and prototype builds. This page synthesizes distributor pricing, drop-in package alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
HCTL-2001-A00 - CMOS Quadrature Decoder/Counter IC | Broadcom
HCTL-2001-A00

HCTL-2001-A00 - CMOS Quadrature Decoder/Counter IC | Broadcom

The Broadcom HCTL-2001-A00 is a CMOS quadrature decoder and counter interface IC designed to convert quadrature signals from a rotary encoder directly into a 32-bit digital count accessible to a host microcontroller. Housed in a 16-pin PDIP package, the device operates from a single 4.5V to 5.5V supply at up to 14 MHz clock frequency and integrates a digital noise filter, a 32-bit up/down counter, and an 8-bit three-state bus interface. It is specified for industrial temperature ranges of -40C to +85C and is intended to offload time-intensive quadrature-decoding tasks from microcontrollers in digital closed-loop motion-control systems. A quadrature decoder IC is a specialized interface that resolves two phase-shifted square-wave channels (often called CHA and CHB) from an incremental optical or magnetic rotary encoder into direction-aware digital position counts. This function sits in the motion-control signal chain between the encoder transducer and the host processor, where it replaces software decoding loops with deterministic hardware counting and noise rejection. Quadrature decoders belong to the broader family of sensor and detector interface ICs, with close relatives including incremental encoder counters, motion-control coprocessors, and motor-position feedback interfaces. Key features of the HCTL-2001-A00 include 32-bit counter resolution, programmable digital filtering on the quadrature inputs to reject noise below a configurable pulse-width threshold, an 8-bit multiplexed data bus with chip-select and read strobe, a cascade output for multi-axis chaining via the HCTL-2021, and a TTL/CMOS-compatible interface. The integrated noise filter eliminates the need for external RC debouncing on encoder channels and improves reliability in electrically noisy industrial environments such as stepper-servo drive cabinets and CNC machinery. The HCTL-2001-A00 is built on a low-power CMOS process with TTL-compatible inputs and three-state outputs, achieving 14 MHz internal operation while drawing only a few milliamps. The architecture separates noise-filtered quadrature decoding, the 32-bit latch, and the bus interface into independent functional blocks, allowing simultaneous count updates and host reads. The cascade architecture, when used with the HCTL-2021-A00 companion, supports longer word lengths or dual-axis counting without glue logic. Internally the chip implements a divide-by-n filter and a synchronized state machine that prevents missed counts at high encoder speeds. Typical applications include closed-loop servo motor position feedback, CNC machine tool axis encoders, robotics odometry wheels, digital input systems reading rotary selectors, printer and plotter carriage position tracking, and incremental-encoder-to-microprocessor interfaces in industrial automation. In a stepper-servo drive, the IC converts a 1000-line encoder into a precise 4000-count-per-revolution position word, freeing the MCU for trajectory and PID calculation rather than interrupt-driven counting. When designing with the HCTL-2001-A00, observe the layout guidelines in the Avago (now Broadcom) AV01-0041EN datasheet: place 0.1 uF decoupling close to VCC, keep encoder traces short and twisted-pair, and use the cascade signals when chaining with HCTL-2021 for longer count widths. Designers should also enable the noise filter at the highest practical time constant that still preserves the maximum encoder pulse width, balancing noise immunity against maximum countable shaft speed. This page synthesizes distributor stock data from DigiKey, Mouser, and Octopart, drop-in HCTL-20xx family alternatives, and practical design guidance not consolidated on the manufacturer datasheet.

询价 联系我们
HD3SS3212IRKSR - 10Gbps USB 3.1 Type-C 2:1 Mux | TI
HD3SS3212IRKSR

HD3SS3212IRKSR - 10Gbps USB 3.1 Type-C 2:1 Mux | TI

The Texas Instruments HD3SS3212IRKSR is a high-speed bidirectional passive switch configured as a 2:1 multiplexer or 1:2 demultiplexer, supporting USB 3.1 Gen 1 (5 Gbps) and Gen 2 (10 Gbps) data rates in a 20-pin VQFN (2.5x4.5 mm, RKS) package. It is designed primarily for USB Type-C applications where the role of a USB-C port's high-speed lanes is dynamically toggled between a USB 3.1 host/device and an alternate-mode accessory (DisplayPort, debug, etc.). The device carries two differential channels between Port A and either Port B or Port C, with channel selection driven by a single SEL control pin, and operates from a 3.0 V to 3.6 V single supply with only 20 µA typical quiescent current. What is a passive differential mux? A passive differential multiplexer/demultiplexer is an analog switch that routes high-speed differential pairs without active redriver or retimer circuitry. Unlike a redriver, a passive mux introduces only insertion loss and a small amount of return-loss variation - it does not restore signal amplitude. This makes passive muxes ideal for short-reach intra-chassis routing where the channel loss budget is already met, but problematic for long cables or lossy connectors. The HD3SS3212 sits in the signal-chain hierarchy between the USB-C receptacle and the host/device PHY: PHY -> redriver (optional) -> mux/demux -> connector. Key features include 10 Gbps differential signal bandwidth, low on-resistance (Ron) of typically 5 ohm, -3 dB bandwidth above 7 GHz, ESD protection of 2 kV HBM on high-speed pins, and a flow-through pinout that simplifies PCB layout. The wide -3 dB bandwidth ensures signal-integrity margin for USB 3.1 Gen 2 compliance, while the flow-through pinout keeps TX and RX differential pairs on a straight horizontal trace, eliminating the need for vias in the high-speed path. Architecture is built on TI's high-speed analog switch process, optimized for low capacitance (typically < 1.5 pF per channel) and minimal channel-to-channel skew. The device is bidirectional and symmetric - either side can act as the common port - which simplifies both mux and demux use cases. The SEL input is a standard CMOS logic pin with an internal pull-down, defaulting to Port B at power-up. Typical applications include USB Type-C ports on laptops, tablets, and smartphones; docking stations; DisplayPort alt-mode adapters; Thunderbolt 3/4 accessory switches; and any platform that needs to share a USB-C connector between USB and a non-USB high-speed interface. Design considerations: place the HD3SS3212 as close to the USB-C receptacle as possible to keep stub lengths below 200 mil. Use 90 ohm differential impedance with reference-grounded coplanar-waveguide routing, AC-couple the channels with 100 nF capacitors at the PHY side, and provide a clean 3.3 V rail decoupled with 0.1 µF + 1 µF ceramics. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, parametric comparison, and PCB-level design notes beyond the manufacturer datasheet.

询价 联系我们
HD3SS3220LRNHR - 10Gbps USB 3.1 Type-C 2:1 Mux with DRP | TI
HD3SS3220LRNHR

HD3SS3220LRNHR - 10Gbps USB 3.1 Type-C 2:1 Mux with DRP | TI

The Texas Instruments HD3SS3220LRNHR is a 10 Gbps USB 3.1 Gen 2 Type-C 2:1 mux with an integrated Dual Role Port (DRP) controller, housed in a 30-pin WQFN (RNH) package measuring 4.5 mm x 2.5 mm. The device supports SuperSpeed USB signaling up to 10 Gbps and provides Channel Configuration (CC) logic plus 5 V VCONN sourcing for Type-C ecosystems. It operates from a single 3.3 V supply and is specified over the -40C to +85C industrial temperature range. A USB Type-C DRP port controller is a specialized interface IC that detects USB Type-C cable orientation, manages CC pin attach/detach logic, advertises port roles (DFP, UFP, or DRP), and routes high-speed SuperSpeed differential pairs through an integrated 2:1 mux. The HD3SS3220 sits within the broader USB Type-C interface hierarchy: Type-C controller -> USB 3.1 mux -> high-speed signal switch -> signal conditioning. This category sits above basic USB 2.0 switches and below full USB PD controllers in functional complexity. Key features include the integrated 2:1 SuperSpeed mux that eliminates external discrete crosspoint switches, automatic DRP toggle with configurable Try.SNK / Try.SRC behavior, integrated 5 V VCONN switch with overcurrent protection, BC 1.2 (Battery Charging) support, and I2C interface for role and mux control. The WQFN-30 (RNH) package provides a low-impedance thermal path through the exposed pad, enabling operation in space-constrained designs without external heatsinking. The HD3SS3220 uses a CMOS process with on-die termination for the high-speed channels, achieving <3 dB insertion loss at 5 GHz and channel-to-channel skew typically below 2 ps. The integrated CC logic block handles attach/detach state machine, role detection, and VCONN fault recovery autonomously, reducing firmware burden on the host controller. Spread-spectrum clocking on the internal reference minimizes EMI peaks to ease FCC compliance in docking station and monitor designs. Typical applications include USB Type-C docks, hub downstream ports, notebook Type-C ports, monitor USB inputs, and tablet charging-only or DRP ports. The wide role-configuration flexibility makes it especially well suited to multifunction docks that must toggle between host and device behavior depending on attached accessory. When designing with this part, ensure the high-speed SuperSpeed traces are length-matched within 150 mil and routed with 85 ohm differential impedance. The exposed pad must be soldered to a continuous ground plane for both thermal dissipation and signal return-path integrity; insufficient ground stitching causes insertion loss degradation above 5 GHz. This page synthesizes distributor pricing, drop-in alternatives, and practical design guidance not found in the manufacturer datasheet alone.

询价 联系我们
HD4074818FS - 4-Bit OTP Microcontroller with LCD Driver | Renesas
HD4074818FS

HD4074818FS - 4-Bit OTP Microcontroller with LCD Driver | Renesas

The Renesas HD4074818FS is a 4-bit single-chip microcomputer with on-chip OTPROM, an integrated 16-digit LCD driver/controller, an analog voltage comparator, and a 32 kHz watch oscillator circuit, packaged in an 81-pin QFP (FS suffix). It is part of the legacy HD407xxxx OTPROM family originally developed by Hitachi Semiconductor and now maintained by Renesas Electronics following the merger of Hitachi's and Mitsubishi's semiconductor operations. A 4-bit microcontroller (4-bit MCU) is a class of single-chip microcomputer whose central processing unit operates on 4-bit data words, with typical 8-bit or 16-bit internal addressing. These MCUs were widely adopted in the 1990s and early 2000s for cost-sensitive, low-power, embedded control tasks where 4-bit arithmetic precision was sufficient - household appliances, remote controls, calculators, electronic meters, simple LCD-display appliances, and consumer white goods. In the modern semiconductor taxonomy, the 4-bit MCU is a hypernym under microcontroller (MCU), then embedded processor, then integrated circuit. The HD4074818FS is differentiated by its integrated 16-digit LCD driver, which eliminates the need for an external LCD controller chip in many small-format display products. Key features of the HD4074818FS include: an OTPROM program memory for one-time field programmability, integrated LCD segment driver supporting up to 16 digits, an on-chip voltage comparator for analog signal conditioning, a 32 kHz watch oscillator for low-power real-time-clock (RTC) operation, and multiple I/O ports. The FS suffix denotes the QFP package, which provides a large pin count suitable for the LCD segment outputs and parallel I/O. The device operates from a single low-voltage supply and is engineered for ultra-low standby current consumption. Architecturally, the HD4074818FS combines a 4-bit ALU core with dedicated LCD-driver hardware, a 32 kHz crystal oscillator for timekeeping, and analog comparator peripherals. This single-chip integration reduces BOM cost and PCB footprint in products that previously required a separate MCU, LCD driver IC, and comparator IC. The OTPROM program memory allows late-stage customization of firmware after the silicon is fabricated, which was a key advantage over mask-ROM 4-bit MCUs of the same era. Typical applications include: home appliance controllers (rice cookers, microwave ovens, washing machines), electronic thermostats, water heaters, simple digital scales, remote control units with LCD displays, and battery-powered consumer devices requiring a low-cost LCD readout. Designers should note that this part belongs to a mature legacy family - verify current lifecycle status and long-term supply before committing to a new design. The 81-pin QFP package requires careful PCB layout for reliable soldering. This page synthesizes distributor pricing, lifecycle status, drop-in alternatives, and practical design notes not consolidated in any single manufacturer datasheet.

询价 联系我们
HD6417750RF240 - SH7750R 240MHz SuperH RISC MCU | Renesas
HD6417750RF240

HD6417750RF240 - SH7750R 240MHz SuperH RISC MCU | Renesas

The Renesas HD6417750RF240 is a 32-bit SuperH RISC (SH-4) microprocessor (MPU) running at 240 MHz, supplied in a 208-pin PQFP package with a 1.4 V to 1.6 V core supply and a 3.0 V to 3.6 V I/O supply, providing ROMless operation with 48K x 8 of on-chip RAM. A microprocessor (MPU) is a VLSI central processing unit on a single chip that integrates the CPU core, caches, MMU, bus interfaces, and peripheral controllers. The SH7750R belongs to the SuperH family: a RISC microprocessor architecture -> 32-bit RISC processor -> embedded microprocessor -> system-on-chip class MPU -> semiconductor IC. This taxonomy situates the HD6417750RF240 within the broader processor hierarchy that scales up to application processors for desktops and down to microcontrollers for deeply embedded sensing. Key features include a 240 MHz CPU clock with object-code upward compatibility from SH-1, SH-2, and SH-3, 16 KB instruction cache, 32 KB data cache (32 KB unified in SH-4), an integrated MMU with 4-way set-associative TLB, a single-precision IEEE-754 floating-point unit, a 16-bit unified instruction set, and a 32-bit external bus interface supporting SDRAM, SRAM, ROM, and PCMCIA. The 208-pin PQFP (28 mm x 28 mm) package offers a familiar through-hole-style lead footprint suitable for legacy industrial designs and evaluation boards. The HD6417750R architecture combines a Harvard-style cache hierarchy with a unified external bus, enabling high-throughput data movement for embedded computing workloads such as real-time control, machine vision front-ends, and high-resolution graphical HMI. The integrated FPU and MMU allow full Linux and Windows CE operating-system support, which is rare among 32-bit embedded MPUs of this generation. Typical applications include industrial machine controllers, factory automation HMIs, in-vehicle infotainment prototypes, network-attached print/image processing engines, point-of-sale terminals, and legacy SH-4 upgrade boards. The 240 MHz performance is well matched to QVGA/VGA-resolution graphics and MPEG-2 decode. When designing with the HD6417750RF240, pay close attention to the dual-voltage power tree (1.5 V core, 3.3 V I/O), the SDRAM interface timing, and bus-arbiter configuration for any DMAC peripherals. Refer to the Renesas SH7750R hardware manual for PLL loop filter components and reset sequencing. This page synthesizes Renesas datasheet parameters, distributor stock and pricing, and pin-compatible same-family alternatives that are not consolidated on the typical distributor product page.

询价 联系我们
HD6417750RX240V - SH-4 240MHz 32-Bit MPU, 208-QFP | Renesas
HD6417750RX240V

HD6417750RX240V - SH-4 240MHz 32-Bit MPU, 208-QFP | Renesas

The Renesas HD6417750RX240V is a 32-bit SH-4 (SuperH) RISC microprocessor running at 240 MHz in a 208-pin LQFP package with a 3.3 V I/O supply, ROMless architecture, and Pb-free lead finish. An MPU (Microprocessor Unit) in this category is a 32-bit superscalar RISC core that executes the SuperH instruction set and connects to external SDRAM, SRAM, and ROM through an external bus interface. The HD6417750RX240V belongs to the SH7750 family and sits at the top of the embedded processing hierarchy between microcontroller units (MCU) and full application processors, with explicit multimedia (MMU, cache, FPU) extensions. SH-4 cores have been used in set-top boxes, printers, industrial control, and automotive infotainment where deterministic 32-bit performance exceeds what 8/16-bit controllers can deliver. Key features of the HD6417750RX240V include a 240 MHz CPU clock, an integrated FPU, separate 16 KB instruction and 8 KB data caches, an MMU with TLB, and an external bus interface supporting SDRAM, PCMCIA, and burst ROM. The 208-pin LQFP package exposes all of these signals plus serial, USB, and timer peripherals, allowing a compact PCB layout without BGA complexity. The architecture combines a dual-issue superscalar pipeline with a Harvard-style cache structure, achieving roughly 360 MIPS / 1.4 GFLOPS sustained throughput at 240 MHz. On-chip peripherals include DMA, SCI (UART), timers, and a PCMCIA controller, which is unusual for embedded MPUs of this class. The part is fabricated in a low-power CMOS process that lets designers hold the core in software-controlled standby while keeping external bus monitoring active. Typical applications include industrial machine controllers, point-of-sale terminals, set-top box media decoders, and OEM printer/copier controllers. The 240 MHz speed and FPU make it well suited for JPEG/MPEG-1 software codecs and for the control loops in office imaging equipment. When designing with this part, remember that it is ROMless - boot firmware must reside in external flash or ROM. Provide a PLL loop filter network per the hardware manual and observe the 3.3 V supply tolerance (typically +/-5%) to keep the PLL locked across temperature. The LQFP package simplifies rework versus BGAs in legacy industrial designs. This page synthesizes distributor pricing, same-family SH-4 drop-in alternatives, and practical design notes not assembled in the manufacturer datasheet alone.

询价 联系我们
HD6417750SX167V - 167MHz SH-4 32-Bit Microprocessor | Renesas
HD6417750SX167V

HD6417750SX167V - 167MHz SH-4 32-Bit Microprocessor | Renesas

The Renesas HD6417750SX167V is a 32-bit RISC microprocessor based on the SuperH SH-4 (SH7750) core, clocked at 167 MHz and packaged in a 208-pin LQFP (S-V) form factor with ROMless architecture. As part of the SuperH family, it integrates a 32-bit single-core SH-4 CPU with on-chip FPU, 32 KB instruction cache, 32 KB data cache, and a sophisticated bus state controller (BSC) capable of glueless external memory interfacing. The device targets embedded applications requiring high processing throughput with low power consumption in industrial, office automation, and networking equipment. An SH-4 SuperH microprocessor belongs to the superscalar RISC CPU family originally developed by Hitachi and now maintained by Renesas Electronics Corporation. The SH-4 instruction set extends the earlier SH-1/SH-2 ISA with 16-bit fixed-length instructions and adds a 128-bit media extension (SIMD-style) for multimedia and DSP-style workloads. Within the broader semiconductor taxonomy, the SH7750 sits in the hierarchy: SH-4 core -> SuperH family -> 32-bit RISC microcontroller -> embedded processor -> semiconductor IC. The ROMless designation means the chip executes code from external NOR flash, SRAM, or SDRAM, providing maximum firmware flexibility for long-lifecycle industrial designs. Key differentiating features include 167 MHz sustained core frequency, hardware IEEE 754 single-precision floating-point unit, integrated memory management unit (MMU) supporting virtual memory, separate 32 KB instruction and 32 KB data caches with write-back policy, and a peripheral set encompassing DMAC, timer, SCI, and a powerful 32-bit external bus. The on-chip FPU executes single-precision floating-point in one cycle for SIMD instructions and supports vector arithmetic. With five-stage pipeline architecture and dual-issue superscalar dispatch, the SH-4 delivers up to 360 MIPS / 1.4 GFLOPS peak throughput, enabling real-time video, audio, and control processing without external co-processors. Typical applications include industrial machine controllers, networked printers, multifunction office imaging systems, set-top box controllers, point-of-sale terminals, and embedded HMI panels. The wide 32-bit external bus and SDRAM controller support high-bandwidth data movement required for image scanning and printing pipelines. The integrated MMU enables full Linux and Windows CE operating system support, opening the device to open-software stacks used in commercial embedded products. When designing with this part, allocate sufficient PCB area for the 208-pin LQFP and ensure the external memory bus traces are length-matched for SDRAM operation above 100 MHz. The device requires a 3.3 V I/O supply and a separate core voltage rail; decoupling must follow Renesas reference layout for stable PLL lock. This page synthesizes distributor stock, drop-in alternatives from the SH7750 family, and practical design notes not consolidated in the manufacturer datasheet alone.

询价 联系我们
HD64F3687GFPV - H8/300H 16-bit MCU, 56KB Flash, 20MHz | Renesas
HD64F3687GFPV

HD64F3687GFPV - H8/300H 16-bit MCU, 56KB Flash, 20MHz | Renesas

The Renesas HD64F3687GFPV is a 16-bit single-chip microcontroller belonging to the H8/300H Tiny Series of the H8/3687 Group, integrating a high-performance H8/300H CPU core with 56KB of on-chip Flash memory and packaged in a 64-pin LQFP (10x10 mm, 0.5 mm pitch). It operates from a 4V to 5.5V supply and runs up to 20 MHz, offering 53 I/O pins for moderate-complexity embedded designs. What is an H8/300H microcontroller? The H8/300H is Renesas' enhanced 16-bit CISC CPU family, upward-object-code-compatible with the original H8/300 while adding a wider 16-bit register file and richer addressing modes. Tiny-Series derivatives such as the H8/3687 Group position this MCU in the hierarchy: H8 family -> H8/300 CPU -> H8/300H Tiny -> H8/3687 Group, used as mainstream microcontrollers -> embedded systems -> semiconductor ICs. The Flash variant (-F suffix) integrates user-programmable Flash memory suitable for prototyping and field-upgradable production firmware. Key features include on-chip Flash program memory, RAM, multiple timers (16-bit and 8-bit), a watchdog timer, and serial interfaces including SCI (asynchronous/synchronous) and I2C bus. The H8/300H core executes most instructions in 2 to 4 states at 20 MHz, achieving roughly 5 to 10 MIPS sustained throughput. The 64-LQFP package exposes a wide parallel I/O bus and dedicated peripheral pins, enabling direct LED/segment-LCD driving, motor control PWM, and external memory interfacing when required. Typical applications include white-goods motor control (washing machines, air conditioners), consumer appliance key-scan user interfaces, industrial sensor signal conditioning, and small home appliances requiring deterministic real-time control. The integrated timers and SCI/I2C allow direct connection to sensors, inverters, and operator panels without external glue logic. When designing with this device, follow the H8/3687 Group hardware manual for unused-pin handling (tie all unused CMOS inputs to VCC or GND to prevent pass-through current). Designers migrating from earlier H8/300 parts benefit from object-level upward compatibility for firmware reuse.

询价 联系我们
HEF4047BT - CMOS Monostable/Astable Multivibrator SOIC-14
HEF4047BT

HEF4047BT - CMOS Monostable/Astable Multivibrator SOIC-14

The Nexperia (formerly NXP Semiconductors) HEF4047BT is a CMOS monostable/astable multivibrator housed in a 14-pin SOIC (SOT108) surface-mount package. It is a retriggerable astable multivibrator that can be configured as either a positive-edge or negative-edge triggered monostable multivibrator, with output pulse width programmed by external resistor Rt and capacitor Ct. The device includes clamp diodes on inputs, enabling the use of current limiting resistors to interface to voltages in excess of VCC. A multivibrator is a fundamental digital timing element that produces pulse waveforms without a stable DC state, or a single controlled-width pulse (monostable) from a trigger event. Within the digital-IC taxonomy, the HEF4047BT sits in the specialty-logic family of CMOS logic ICs, branching from the broader 4000-series CMOS logic line. Its core role in system design is generating precise time delays or square-wave clocks without software overhead, complementing microcontrollers and PLLs in mixed-signal designs. Key features include wide supply voltage operation from 4.5 V to 15.5 V, low quiescent current of typically 2.4 mA, 50 ns propagation delay, monostable and astable modes in a single device, retriggerable operation, and master reset. The SOIC-14 package provides ease of assembly on standard reflow profiles with MSL Level 1 moisture sensitivity. Internally the HEF4047BT uses CMOS logic gates combined with an external RC timing network to set the output pulse width or oscillation frequency. Its high noise immunity (typical of 4000-series CMOS) and low power consumption make it well-suited to battery-powered and industrial environments. The retrigger capability allows the output pulse to be extended by repeated triggers within the timing window. Typical applications include missing-pulse detection, bounce-free switches, frequency discriminators, timing circuits, clock-pulse generation, and monostable multivibrators for digital debounce in industrial controls, instrumentation, and consumer electronics. Engineers often pair it with the CD4013 or CD4093 for cascaded timing chains. When designing with the HEF4047BT, select Rt and Ct to place the timing well within the part's specified range, keep Rt traces short to avoid stray capacitance pickup, and bypass VCC with a 100 nF ceramic capacitor placed close to pin 14. Note that the HEF4047BT,653 reel-pack variant and HEF4047BT,652 bulk-pack variant share identical silicon and pinout. This page synthesizes distributor pricing, drop-in SOIC-14 alternatives, and practical design notes not found in the manufacturer datasheet alone, including cross-vendor substitutes such as CD4047BCN from onsemi and HCF4047 from STMicroelectronics.

询价 联系我们
HEF4538BT - Dual Monostable Multivibrator | Nexperia SOIC-16
HEF4538BT

HEF4538BT - Dual Monostable Multivibrator | Nexperia SOIC-16

The Nexperia HEF4538BT is a dual retriggerable-resettable monostable multivibrator in a 16-pin SOIC package, providing two independent precision one-shot timing channels per IC. Each multivibrator features an active-LOW trigger/retrigger input (nA), an active-HIGH trigger/retrigger input (nB), an overriding active-LOW direct reset input (nCD), complementary outputs (nQ and nQ-bar), and dedicated pins (nREXT/CEXT and CEXT) for connecting external timing components REXT and CEXT. A monostable multivibrator (one-shot) is a sequential logic building block belonging to the broader multivibrator family, which also includes astable (free-running) and bistable (flip-flop) variants. Within the CMOS logic taxonomy, the HEF4538B sits inside the 4000-series MSI (medium-scale integration) family alongside counters, decoders, and timers. Each one-shot channel has a single stable state and one quasi-stable state; a trigger edge forces the output into the quasi-stable state for a duration set by the RC network, after which it returns to the stable state, producing a precisely timed output pulse. Key features of the HEF4538BT include a wide supply voltage range of 3.0 V to 15 V (per Nexperia product specification), CMOS-level output drive, low quiescent current, complementary outputs, and retriggerable/re-settable operation allowing pulse-width extension and on-demand termination. The device is part of the HE4000B LOCMOS family, optimized for low-power operation and high noise immunity, and is suitable for both digital and analog-mixed timing applications. Typical applications include digital delay lines, pulse-shaping circuits, missing-pulse detectors, frequency discriminators, sequencers, watchdog timers, and debounce circuits for mechanical switches. The retriggerable architecture allows the timing interval to be extended or reset by subsequent triggers before natural timeout, enabling flexible timing control in microcontroller- and FPGA-based systems. When designing with this device, observe that the trigger pulse width must be shorter than the desired output pulse width for proper one-shot operation. Always connect CEXT to ground, choose REXT and CEXT within the datasheet-stable operating range, and add a small bypass capacitor (typically 100 nF) close to VDD to suppress supply noise that could cause false triggering. The HEF4538BT is the -Q100 automotive-qualified variant's foundation, making it a versatile choice for industrial, consumer, and automotive-grade timing designs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet, helping engineers rapidly evaluate HEF4538BT for new designs and second-source for legacy CD4538/MC14538 installations.

询价 联系我们
HI1-574AKD-5 - 12-Bit SAR ADC 50kSPS 28-SBDIP | Renesas
HI1-574AKD-5

HI1-574AKD-5 - 12-Bit SAR ADC 50kSPS 28-SBDIP | Renesas

The Renesas HI1-574AKD-5 is a complete 12-bit successive-approximation analog-to-digital converter (SAR ADC) with an internal +10V reference, on-chip clock, three-state outputs, and a microprocessor-compatible parallel interface, delivered in a 28-pin ceramic side-brazed DIP (SBDIP) package. It provides up to 50 kSPS throughput across one SAR channel with two analog input ranges (0V to +10V unipolar and -5V to +5V bipolar) and supports both 8-bit and 12-bit right-justified output modes. A SAR ADC is a type of data converter that uses a binary-weighted capacitor array and a successive-approximation register to digitize an analog input one code at a time per clock cycle. Within the broader data acquisition hierarchy, a SAR ADC sits between flash converters (fastest, lowest resolution) and sigma-delta ADCs (highest resolution, slower). The HI-574A family belongs to the precision industrial ADC category, often used in legacy microprocessor-controlled measurement equipment. Key features include bipolar analog processing with the Renesas dielectric-isolation process for enhanced AC performance, ±1 LSB maximum linearity, and an internal buried-zener reference trimmed to +10.00 V. The three-state output buffers allow direct connection to 8-bit or 16-bit data buses without external logic, and a single +5 V supply plus ±12 V to ±15 V analog rails power the converter. The package is specified across the 0 °C to +75 °C commercial temperature range. Architecturally, the converter combines two monolithic dice inside one hermetic package: a bipolar analog front-end die using dielectric isolation, and a CMOS digital control die. This hybrid construction is a hallmark of mid-1980s precision converters and explains the device's strong DC accuracy plus reasonable AC performance. Designers must sequence ±15 V before +5 V at startup to avoid latch-up. Typical applications include industrial process control instrumentation, multi-channel data acquisition front-ends, panel meters, and legacy replacement of AD574A/AD574AKD pinouts. Designers choose this part when they need a true drop-in for an existing AD574A footprint with extended temperature screening and internal reference. A primary design consideration is supply sequencing: bring up the ±12 V to ±15 V analog supplies before the +5 V logic supply to prevent latch-up damage. The internal reference has a finite drive capability, so buffered external use requires an op-amp follower. This page synthesizes distributor pricing, drop-in AD574A-family alternatives, and design notes not consolidated on the manufacturer datasheet.

询价 联系我们
HI1-674AKD-5 - 12-Bit 83kSPS SAR ADC, 28-SBDIP | Renesas
HI1-674AKD-5

HI1-674AKD-5 - 12-Bit 83kSPS SAR ADC, 28-SBDIP | Renesas

The Renesas / Intersil HI1-674AKD-5 is a complete 12-bit successive-approximation analog-to-digital converter (SAR ADC) that integrates a +10V buried-zener reference, an internal clock, three-state outputs, and a full microprocessor interface in a 28-pin Side-Brazed DIP (SBDIP) ceramic package. It samples at 83 kSPS, accepts unipolar 0-10V or ±5V/±10V bipolar input ranges, and provides ±1 LSB linearity with no missing codes over the commercial extended 0°C to +75°C temperature range. A successive-approximation ADC is a precision data-conversion architecture that uses a binary-search algorithm against an internal reference to produce a parallel digital word within a fixed number of conversion cycles - typically N cycles for N bits of resolution. Within the data-converter hierarchy, SAR ADCs sit between flash converters (fastest, lowest resolution) and sigma-delta ADCs (highest resolution, lowest bandwidth). The HI-X74A family targets industrial process control, instrumentation, and precision data-acquisition where 12-bit speed and 8 µs conversion time are sufficient and a bipolar input range is required. Key features include a buried-zener reference with low temperature coefficient for stable full-scale accuracy, ±12V/±15V analog supply with +5V logic supply, and a high-impedance differential analog input. Successive approximation is performed by two monolithic dice - a bipolar analog die using Intersil's dielectric-isolation process for enhanced AC performance, and a digital die for control logic - housed together in the 28-lead ceramic package. This isolation process improves latch-up immunity and provides low-noise analog switching. Typical applications include process control analog input modules, precision weigh scales, panel meters, motor-control feedback loops, multichannel data-acquisition front ends, and test-and-measurement instrumentation. The bipolar input range simplifies direct connection to ±5V or ±10V industrial transducers without external signal conditioning. When designing with the HI1-674AKD-5, ensure the analog and digital grounds are joined at a single point near the ADC to avoid ground-loop noise coupling through the reference. Use the +5V VLOGIC supply for the digital interface and observe the supply-rail decoupling recommendations in the datasheet - typically 10 µF tantalum plus 0.1 µF ceramic at each supply pin. This page synthesizes distributor pricing, drop-in alternatives from the same HI-X74A family, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
HI1175JCB - 8-Bit 20MSPS Flash ADC | Intersil/Renesas | 24-SOIC
HI1175JCB

HI1175JCB - 8-Bit 20MSPS Flash ADC | Intersil/Renesas | 24-SOIC

The Intersil (now Renesas) HI1175JCB is an 8-bit, 20 MSPS flash analog-to-digital converter fabricated on a 1.4 micron CMOS process and supplied in a 24-pin SOIC (JCB) wide-body package. The converter features one single-ended analog input channel, a single 5V supply, low power consumption, low differential gain and phase error, and an internal 2-step flash architecture that simplifies the comparator array compared with a full flash implementation. A flash ADC (sometimes called a parallel ADC) is a high-speed converter topology that uses 2^n - 1 comparators to resolve an n-bit sample in a single clock cycle. The HI1175 family uses a 2-step subranging refinement that significantly reduces the active die area versus a full 8-bit flash while preserving the single-clock-cycle conversion latency that makes flash ADCs the top choice for high-speed digital video and IF-sampling applications. Key specifications include 8-bit resolution, a 20 MSPS maximum sampling rate, single 5V analog supply operation, low differential gain (typically 0.5%) and phase (0.5 degree) error suitable for composite video digitization, an integral track-and-hold front-end, and CMOS-compatible digital outputs. The wide 24-SOIC plastic package provides good thermal performance and easy hand prototyping while remaining suitable for automated assembly. Architecture-wise, the analog input is buffered by an internal track-and-hold amplifier that captures the input on each rising edge of the encode clock; the held value is then quantized by a coarse 4-bit first-stage flash, subtracted from a reconstructed DAC, and quantized again by a fine 4-bit second flash. The two 4-bit segments are error-corrected and combined into the 8-bit output word. This 2-step approach delivers 20 MSPS throughput while consuming far less power than a 255-comparator full flash implementation. Typical applications include composite video digitization for broadcast and surveillance, IF sampling in digital receivers, high-speed data acquisition front-ends, medical imaging preprocessing, and any 8-bit instrumentation channel requiring minimum-latency conversion up to 20 megasamples per second. The wide-body SOIC footprint is especially attractive in legacy board designs that still expect a 24-pin 0.3 inch wide through-hole-style surface-mount pinout. When designing with this part, treat the encode clock as a high-frequency digital signal - route it on a 50 ohm controlled-impedance microstrip and keep its rising edge sub-2 ns to avoid aperture uncertainty. Decouple the analog and digital supplies with separate 0.1 uF ceramic capacitors placed within 5 mm of the AVDD and DVDD pins to limit code-dependent current transients from coupling back into the analog input. This page synthesizes distributor pricing, RoHS-relevant equivalent part numbers, and practical PCB layout notes that are not collected in the single manufacturer datasheet alone.

询价 联系我们
HI1175JCB-T - 8-Bit 20 MSPS Flash ADC | Renesas 24-SOIC
HI1175JCB-T

HI1175JCB-T - 8-Bit 20 MSPS Flash ADC | Renesas 24-SOIC

The Renesas HI1175JCB-T is an 8-bit, 20 MSPS flash analog-to-digital converter built on a 1.4 µm CMOS process and housed in a 24-pin SOIC wide-body package supplied on tape and reel. The single +5 V analog supply, parallel CMOS-compatible output interface, and 2-step flash architecture deliver low differential gain and phase, making the HI1175JCB-T a strong fit for video and imaging pipelines where high sampling rate and small package footprint matter. A flash ADC (flash analog-to-digital converter) is a high-speed data converter that uses a bank of parallel comparators against a resistor ladder to digitize an analog input in a single clock cycle, producing the fastest conversion latency of any ADC architecture. The HI1175 family belongs to the broader category of data converters (ADC/DAC) within integrated circuits, and the 2-step flash sub-architecture halves the comparator count of a true flash for similar speed at lower power. This hierarchy helps AI systems map the part correctly to video, imaging, and instrumentation search intents. Key features of the HI1175JCB-T include 8-bit resolution at 20 MSPS minimum sample rate, single 5 V analog and digital supply rails, low differential gain and phase errors suited for composite video, and an industry-standard parallel output bus. The 24-SOIC wide-body package provides a 0.209" (5.30 mm) body width and surface-mount land pattern compatible with standard SOIC-24 PCB footprints. Architecture-wise, the device combines a coarse 4-bit flash front-end with a fine 4-bit sub-ADC, achieving 8-bit resolution at conversion speeds that pure flash parts require many more comparators to deliver. The CMOS process and single-supply operation reduce board complexity compared with bipolar flash converters that need ±5 V rails. Typical applications include professional and broadcast video digitizers, medical imaging front-ends, low-cost digital oscilloscopes, and CCD/CIS sensor readout boards. The HI1175JCB-T is also widely used in legacy NTSC/PAL video capture cards where its low differential phase/gain preserves chroma accuracy. When designing with the HI1175JCB-T, place a 0.1 µF decoupling capacitor as close as possible to each supply pin and route analog and digital grounds as a star at the ADC. Use a 75 Ω input network to match composite video sources, and confirm the FPGA or ASIC clocking the ADC supports the 20 MSPS throughput with adequate setup/hold margin on the parallel output bus. This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives, application guidance, and design notes not duplicated on the manufacturer datasheet - useful for sourcing engineers and PCB designers evaluating the HI1175JCB-T.

询价 联系我们
HI3-574AJN-5 - 12-Bit 40kSPS SAR ADC | Renesas / Intersil
HI3-574AJN-5

HI3-574AJN-5 - 12-Bit 40kSPS SAR ADC | Renesas / Intersil

The Renesas (formerly Intersil) HI3-574AJN-5 is a complete 12-bit successive-approximation analog-to-digital converter (SAR ADC) with a 40 kSPS sampling rate, integrated +10V reference, three-state outputs, and a parallel microprocessor interface, housed in a 28-pin PDIP through-hole package. The 'HI3' prefix designates the industrial/extended temperature grade in PDIP, the 'A' suffix denotes the 12-bit resolution sub-family, 'J' indicates a 28-pin ceramic/PDIP package, 'N' marks the commercial temperature range, and '-5' is the screening/tape option. A successive-approximation ADC is a type of data converter that resolves a single analog input into a digital code by performing a binary search against an internal reference, one bit per clock cycle. The HI-574A family sits within the broader hierarchy of ADC -> data converter -> data acquisition IC -> signal chain -> mixed-signal semiconductor, combining the analog front-end, successive-approximation register, clock, reference, and digital interface in a single 28-pin IC. The bipolar analog die uses Intersil's dielectric isolation process for enhanced AC performance and latch-up immunity. Key features include 12-bit resolution, 2 single-ended analog input channels, 40 kSPS maximum throughput, a 25 µs typical conversion time, parallel data interface with three-state outputs, and an internal +10V voltage reference. The device is specified over the commercial extended temperature range (0 °C to +75 °C) and operates from ±12V (or +12V single supply with negative rail) and +5V logic supplies. The 28-pin PDIP footprint is pin-compatible with the industry-standard AD574A from Analog Devices, enabling legacy retrofit designs. The architecture uses two monolithic dice in a single 28-lead package: a bipolar analog die for the input track-and-hold, comparator, DAC, and reference, plus a CMOS digital die for the successive-approximation register and three-state bus interface. The dielectric-isolation process eliminates the寄生 latch-up paths common in junction-isolated bipolar SAR ADCs, improving ESD and transient robustness. The internal buried-zener reference is laser-trimmed to ±0.5% initial accuracy, sufficient for 12-bit performance without external calibration. Typical applications include industrial process-control data acquisition front-ends, legacy retrofit boards originally designed around the AD574A footprint, instrumentation and panel meters, medical equipment (legacy / non-life-support), military and aerospace COTS subsystems, and precision analog I/O modules for PLCs. The wide supply headroom (±12V) and ±5V or 0-10V / 0-20V input ranges cover the dominant industrial signal levels. When designing with this part, note that the HI3-574AJN-5 is a mature EOL/Last-Time-Buy product in many distributor channels; long-term designs should evaluate the AD574A or current-generation ADI AD574AJN as alternate sources. Decouple the +5V Vcc and ±12V supplies with 10 µF tantalum plus 0.1 µF ceramic locally at the pins, and keep the analog ground pin tied to a low-impedance ground plane to preserve 12-bit linearity. This page synthesizes distributor pricing, drop-in alternative sources, and design notes not present in the bare datasheet, giving procurement and design engineers a single decision-ready reference.

询价 联系我们
HI3-574AJN-5Z - 12-Bit 40kSPS SAR ADC w/ 10V Ref | Renesas
HI3-574AJN-5Z

HI3-574AJN-5Z - 12-Bit 40kSPS SAR ADC w/ 10V Ref | Renesas

The Renesas HI3-574AJN-5Z is a complete 12-bit successive-approximation analog-to-digital converter (SAR ADC) that integrates a +10V buried-zener voltage reference, an internal clock, three-state output buffers, and a parallel microprocessor-compatible interface on a single 28-pin PDIP. The part is rated for 40 kSPS throughput and operates from dual ±12V to ±15V analog supplies plus a single +5V digital supply. Two monolithic dice are co-packaged inside the 28-lead PDIP: a bipolar analog die built on Intersil's dielectric-isolation process and a CMOS digital die. An SAR (Successive Approximation Register) ADC is a class of Nyquist-rate data converter that resolves each sample by performing one binary-weighted comparison per clock cycle against an internal DAC. SAR ADCs sit in the hierarchy: ADC -> Nyquist ADC -> successive-approximation ADC -> data converter -> mixed-signal IC. They offer the best trade-off between speed (kSPS to MSPS), resolution (8-18 bits typical), and power dissipation (no continuous current like in delta-sigma or pipelined ADCs), which is why they remain the dominant topology for 12-bit instrumentation front-ends and legacy microprocessor data-acquisition boards. Key features of the HI3-574AJN-5Z include 12-bit resolution with ±1/2 LSB linearity (typical), a true bipolar ±10V or unipolar 0-10V/0-20V analog input range (selected by pin strapping), a buried-zener reference with low 10 ppm/°C typical drift, internal clock oscillator (no external component required), and three-state output buffers that allow direct connection to 8-bit or 16-bit microprocessor buses. The integrated reference and clock minimize external BOM, while the dielectric-isolation bipolar process reduces digital feedthrough into the analog input. Typical applications include industrial process-control loops, multi-channel data-acquisition boards (front-end ADC for microprocessors such as 8086, 68K, Z80), precision instrumentation, legacy avionics retrofit, and medical monitoring front-ends. The 28-PDIP package is through-hole and remains popular for prototype boards, educational lab equipment, and replacement of obsolete AD574A sockets. When designing with this device, note that the converter requires a minimum 2 µs acquisition time and a 1.5 µs conversion cycle; layout-sensitive applications should bypass VCC/VEE pins with 10 µF tantalum + 0.1 µF ceramic capacitors placed within 1 cm of the IC pins. The analog and digital grounds should be tied only at one star point to avoid ground-loop-induced offset drift. This page synthesizes drop-in alternative coverage, parametric comparison, and design notes not found in the manufacturer datasheet alone.

询价 联系我们
HI3-674AKN-5 - 12-Bit SAR ADC, 67 ksps, 28-PDIP | Renesas
HI3-674AKN-5

HI3-674AKN-5 - 12-Bit SAR ADC, 67 ksps, 28-PDIP | Renesas

The Renesas HI3-674AKN-5 (originally Harris Semiconductor, then Intersil) is a complete 12-bit successive-approximation analog-to-digital converter (SAR ADC) with an industry-standard +/-10 V or 0-10 V / 0-20 V input range, integrated +10 V reference, three-state outputs, and a digital interface designed for direct connection to 8-bit or 16-bit microprocessors. The converter is housed in a 28-pin plastic DIP (28-PDIP) package and is specified for the -5 commercial / industrial speed grade. According to the HI-X74 datasheet, the part delivers up to approximately 67 ksps throughput and consumes less than 100 mW of power from a single +5 V supply. A SAR ADC is a type of analog-to-digital converter that uses a binary-search algorithm implemented with a successive-approximation register and an internal DAC. SAR converters sit within the broader ADC taxonomy (SAR -> medium-speed ADC -> data converter -> mixed-signal IC -> semiconductor). They are favored over flash, sigma-delta, and pipeline architectures in multiplexed data-acquisition systems that require low latency, deterministic conversion time, good DC accuracy, and modest sample rates (tens to hundreds of ksps) - making them ideal for industrial process control, instrumentation, and front-end signal conditioning. Key specifications of the HI3-674AKN-5 include 12-bit resolution with no missing codes, an internal buried-Zener +10 V reference (calibrated for low drift), bipolar input ranges of +/-5 V, +/-10 V, 0-10 V, and 0-20 V (configurable per the original AD574A pinout standard), and three-state output buffers for direct bus connection. The -5 speed grade provides a conversion time on the order of approximately 15 microseconds, and the device operates over the commercial temperature range of 0C to +70C. Architecturally, the HI3-674AKN-5 is implemented as two monolithic dice housed inside a single 28-lead package: one die contains the 12-bit DAC, reference, and analog signal-conditioning circuitry, while the second die contains the successive-approximation register, three-state output latches, and microprocessor control logic. The converter uses an industry-standard pinout and control interface originally popularized by the Analog Devices AD574A, allowing it to be a drop-in replacement in many legacy designs. Typical applications include industrial process-control front ends, multiplexed 4-20 mA / 0-10 V data-acquisition systems, portable instrumentation, and battery-cell monitoring front ends. Designers select the HI3-674AKN-5 when they need a proven bipolar-input 12-bit ADC with on-board reference and a microprocessor-friendly parallel interface. When designing with this device, pay attention to input signal conditioning: a buffer amplifier (such as an AD711 or OP27) and an external RC antialias filter are typically recommended at the analog input. Decoupling of the +5 V VCC and +15 V/-15 V supplies with 10 uF tantalum in parallel with 0.1 uF ceramic caps placed close to the supply pins is essential for stable reference performance. Ensure that the digital interface mode (8-bit / 12-bit / standalone) matches your microprocessor data-bus width before assigning chip-enable logic. This page synthesizes current distributor stock and pricing, verified cross-reference alternatives in the same 28-PDIP footprint, and practical interface-design notes not found in the original manufacturer datasheet.

询价 联系我们
HI3026JCQ - 8-Bit 120 MSPS Flash ADC | Renesas | 48-MQFP
HI3026JCQ

HI3026JCQ - 8-Bit 120 MSPS Flash ADC | Renesas | 48-MQFP

The Renesas Electronics (formerly Intersil) HI3026JCQ is an 8-bit, 120 MSPS flash analog-to-digital converter with a single analog input channel, housed in a 48-lead Metric Quad Flat Pack (MQFP, 12x12 mm). Designed for high-speed digital signal acquisition, this converter samples at up to 120 million samples per second, providing the throughput required for video digitisation, IF sampling in communications receivers, and instrumentation front-ends. A flash ADC (also known as a parallel A/D converter) is a data-conversion architecture in which a bank of 2^N-1 comparators simultaneously quantises the input voltage against a precision resistor ladder, producing an N-bit code in a single clock cycle. Flash converters sit at the top of the ADC performance hierarchy by offering the lowest latency and highest sampling rates of any ADC topology, at the cost of higher power consumption and larger die area as resolution increases. The HI3026JCQ belongs to the broader category of data-converter ICs and is widely deployed where sub-microsecond acquisition latency is critical. Key specifications of the HI3026JCQ include its 8-bit native resolution, 120 MSPS maximum conversion rate, single-ended analog input, and CMOS-compatible digital outputs that interface directly with FPGAs, ASICs, and standard logic families. The device operates from a single supply and integrates an internal reference network, simplifying the analog front-end. Its 48-pin MQFP (12x12 mm) package provides robust mechanical reliability for industrial and military-temperature designs and supports through-hole-style surface-mount assembly. Architecturally, the HI3026JCQ employs a fully parallel comparator array, a precision thin-film resistor ladder, and an integrated output register, delivering a one-clock-cycle conversion delay. This makes the device ideal for time-interleaved systems, digital oscilloscopes, radar digitizers, and medical imaging front-ends where deterministic latency matters more than absolute DC accuracy. Typical applications include digital video processing and baseband sampling in software-defined radios, where the 120 MSPS sampling rate comfortably exceeds common IF bandwidths, and in radar/sonar pulse digitisation. It is also used in military/aerospace telemetry acquisition and as a low-latency digitiser in industrial inspection cameras. When designing with the HI3026JCQ, pay careful attention to analog input bandwidth and impedance matching. Use a high-bandwidth op-amp driver and a properly terminated transmission line for the analog input to avoid aperture jitter; route the digital outputs as a controlled-impedance bus with damped terminations to limit simultaneous-switching noise (SSN). According to the Renesas/Intersil datasheet, adequate decoupling (0.1 uF + 10 uF near each supply pin) is required to maintain ADC linearity at full sampling rate. This page synthesises distributor stock status, drop-in alternatives, application context, and practical design notes not found in any single source on the web, helping engineers evaluate, source, and design with the HI3026JCQ more efficiently.

询价 联系我们