微控制器

产品（19,000+)

KMPC8540CVT667JB - PowerPC e500 MPU, 667MHz, 783-FCPBGA | NXP
KMPC8540CVT667JB

KMPC8540CVT667JB - PowerPC e500 MPU, 667MHz, 783-FCPBGA | NXP

The NXP KMPC8540CVT667JB is a PowerPC e500-based microprocessor from the MPC85xx family, integrating a single 32-bit core running at 667 MHz in a 783-ball FCPBGA (29x29 mm) package. It belongs to the PowerQUICC III communications processor lineage originally developed by Freescale (now NXP) and is engineered for high-performance networking, telecom, and embedded control applications requiring integrated packet processing. The device features a 32-bit RISC core with memory management, integrated L1/L2 caches, dual GbE MACs, and a multi-channel DMA engine. It is offered in industrial-grade temperature range with typical junction operation from -40C to +105C depending on configuration. A microprocessor (MPU) is a single-chip CPU containing the full arithmetic logic unit, control unit, register file, and integrated peripherals on a single die. The MPC85xx family sits at the top of the embedded MPU hierarchy, between microcontrollers (which integrate Flash and a richer peripheral set) and high-end server CPUs (which use multi-core out-of-order designs). PowerQUICC III specifically targets communications backplane and routing equipment where deterministic packet latency, hardware crypto acceleration, and multi-protocol bus interfaces are required. Key features of the KMPC8540CVT667JB include 32KB L1 instruction cache, 32KB L1 data cache, 256KB L2 cache, dual 10/100/1000 Ethernet MACs, dual 32-bit PCI controllers, DDR memory controller supporting DDR SDRAM, integrated security engine, and four channel DMA. The PowerPC e500 core uses a 7-stage pipeline with dual-issue superscalar execution and Book-E-compliant MMU for embedded Linux, VxWorks, and other RTOS support. The 783-FCPBGA package is a fine-pitch flip-chip BGA with 1.0 mm ball pitch optimized for high-speed signal integrity and multilayer PCB designs. Typical applications for this MPU include enterprise Ethernet switches, wireless base station controllers, industrial routers, telecom backplane cards, and defense/aerospace embedded controllers. The combination of dual GbE MACs, PCI interface, and high CPU frequency makes it especially suited for L2/L3 managed switch line cards and access routers handling wire-speed forwarding. When designing with this part, ensure that PCB stack-up supports the 783-ball 1.0 mm pitch BGA, that DDR trace lengths are matched within the datasheet tolerance window, and that the thermal solution accounts for typical 4-7W active power dissipation. Use the Freescale/NXP BSDL and reference schematics for power-rail sequencing. This page synthesizes distributor pricing, drop-in alternatives, and design notes not found aggregated in the manufacturer datasheet, helping engineers evaluate substitution options for long-lifecycle embedded designs.

询价 联系我们
KMPC8540VT667LB - PowerPC e500 MPU 667MHz 783-FCBGA | NXP
KMPC8540VT667LB

KMPC8540VT667LB - PowerPC e500 MPU 667MHz 783-FCBGA | NXP

The NXP KMPC8540VT667LB is a PowerPC e500 microprocessor from the MPC85xx PowerQUICC III family, integrating a single 32-bit e500 core running at 667 MHz in a 783-pin FCPBGA (29 mm x 29 mm) package. It combines the PowerPC processor core with system logic required for networking, storage, and communications infrastructure, operating from a 1.2 V core supply with dedicated I/O rails. Background: A microprocessor (MPU) is an integrated circuit that contains a full central processing unit on a single die, often paired with integrated memory controllers, peripheral interfaces, and accelerator blocks. The MPC85xx family belongs to the PowerQUICC III hierarchy - high-performance communications processors built on Power Architecture technology, positioned between general-purpose CPUs and application-specific network processors in the broader embedded system taxonomy. Key features include a 32-bit PowerPC e500 core with Book E instruction set support, integrated DDR memory controller, PCI Express and RapidIO fabric interfaces, four GigaBit Ethernet MACs, and an enhanced local bus controller. The device also integrates security acceleration, DMA engines, and dual I2C, SPI, and DUART interfaces, consolidating what previously required multiple companion chips into a single BGA package. The architecture employs a superscalar e500 core backed by L1 instruction and data caches (32 KB each) and a unified L2 cache, delivering deterministic throughput for packet-processing workloads. Hardware-assisted queue management, table lookup acceleration, and CRC engines offload work that would otherwise consume CPU cycles in software, enabling the 667 MHz device to sustain multi-Gbps data plane performance. Typical applications include multi-service routers, Layer 2/3 enterprise switches, network attached storage (NAS) controllers, line cards for base stations, and industrial control gateways. The combination of integrated memory controller and high-speed serial interfaces makes the MPC8540 well suited to designs where board real estate and bill-of-materials count are critical. When designing with this device, allocate at least four PCB layers for the 783-ball FCBGA breakout and follow NXP's reference design for power sequencing - the 1.2 V core rail must ramp before the I/O rails to avoid latch-up. Use controlled-impedance routing for the DDR2 memory channels and observe the strict length-matching tolerances documented in the hardware specifications. This page synthesizes current distributor pricing, validated drop-in MPC85xx family alternatives, and engineering-graded design notes not aggregated in any single distributor page.

询价 联系我们
KMPC8548EVUAUJ - PowerPC e500 MPU 1.333GHz 783-FCBGA | NXP
KMPC8548EVUAUJ

KMPC8548EVUAUJ - PowerPC e500 MPU 1.333GHz 783-FCBGA | NXP

The NXP KMPC8548EVUAUJ is a PowerPC e500 embedded microprocessor from the MPC85xx family operating at up to 1.333 GHz with a single 32-bit core, housed in a 783-ball FCBGA (29x29 mm) package. It integrates a high-performance e500 core with dedicated L1 caches, a 256 KB unified L2 cache, dual Gigabit Ethernet controllers, DDR memory controller, and RapidIO / PCI Express / PCI interfaces, targeting networking, telecom, and industrial embedded applications. Key features include 1.333 GHz core frequency, 32-bit PowerPC e500 architecture, integrated 36-bit DDR memory controller, dual 10/100/1000 Ethernet MACs with TCP/IP acceleration, hardware encryption and pattern matching engines, four DMA channels, and a 783-ball flip-chip BGA package. The device supports extended operating temperature ranges suitable for industrial and networking equipment. An embedded microprocessor (MPU) is a CPU-centric System-on-Chip component designed for headless or RTOS-driven applications where deterministic performance and high-bandwidth I/O are required. The KMPC8548EVUAUJ belongs to the QorIQ / PowerQUICC III lineage and serves as the central processing unit for routers, switches, wireless base stations, and defense electronics, sitting at the top of the system hierarchy above memory ICs, PHYs, and glue logic. Typical applications include enterprise routers and Layer-2/3 switches, wireless infrastructure baseband processing, industrial control and factory-floor networking, single-board computers for defense and aerospace, secure communications gateways, and edge-of-network appliances. The integration of dual GbE plus TCP/IP acceleration makes it particularly well suited for line-rate packet processing without off-CPU assistance. When designing with this MPU, allocate a multi-layer PCB with controlled-impedance routing for DDR, Gigabit Ethernet, and RapidIO/PCIe links. Ensure robust thermal management - the FCBGA package dissipates significant power under sustained load, and a heatsink plus airflow is mandatory in most deployment scenarios. JTAG and COP debug ports must be brought out to test headers for production bring-up.

询价 联系我们
KSZ9692PB - 1Gbps ARM9 Ethernet SoC | Microchip Technology
KSZ9692PB

KSZ9692PB - 1Gbps ARM9 Ethernet SoC | Microchip Technology

The Microchip Technology KSZ9692PB is a highly integrated networking system-on-chip (SoC) built around an ARM 922T 32-bit processor, with 10/100/1000 Ethernet connectivity and operating from 2.5 V and 3.3 V supplies. The device is supplied in a 400-pin PBGA package and targets cost-sensitive, high-bandwidth networking and communications equipment. What is an Ethernet controller SoC? An Ethernet controller SoC combines a processor core, network interfaces, memory interfaces, security functions, and communication peripherals on one semiconductor. This integration reduces the component count and board area needed for an Ethernet node while providing dedicated hardware for packet processing. The KSZ9692PB places that networking capability around an ARM 922T core, making it suitable for gateways, embedded communications equipment, and industrial Ethernet products. Verified product information identifies the device as an ARM9 KSZx692 networking and communications microcontroller with external program memory and 1 Gbps Ethernet capability. Its 2.5 V and 3.3 V supply options support mixed-voltage system designs, while the 400-pin PBGA provides the high-density connection set required by the integrated networking architecture. The product listing also identifies an integrated Gigabit networking and communications controller with an IP security engine. The ARM 922T processor is a 32-bit embedded processing core suitable for control tasks, protocol handling, and network-device management. In this SoC, the processor works with dedicated Ethernet resources rather than serving only as a general-purpose microcontroller. That division of responsibility is important in communications systems where media access, packet transfer, and host-side control must operate predictably at gigabit-class data rates. Typical uses include industrial Ethernet gateways, embedded routers, network interface controllers, communications appliances, and managed access equipment. The external program-memory interface allows the system architecture to separate firmware storage from the SoC, which can be useful when software images differ by product configuration or require updates. Design begins with the manufacturer data sheet rather than distributor summaries. Because the supplied search results do not expose the complete 400-pin assignment, clock limits, memory map, or electrical tables, engineers must verify those details before PCB layout. A 400-pin PBGA also requires careful power distribution, decoupling, high-speed Ethernet routing, thermal analysis, and manufacturing capability. This page combines verified manufacturer and distributor facts with explicit engineering gaps, practical integration guidance, commercial-source links, and a strict assessment of replacement feasibility. It does not present unverified pin mappings, electrical limits, or substitute devices as drop-in replacements.

询价 联系我们
KSZ9692PBI - Gigabit Ethernet ARM9 SoC | Microchip Technology
KSZ9692PBI

KSZ9692PBI - Gigabit Ethernet ARM9 SoC | Microchip Technology

Microchip Technology KSZ9692PBI is a highly integrated networking and communications system-on-chip containing an ARM9 32-bit processor, Gigabit Ethernet connectivity, external program memory support, and hardware security capabilities. The device is identified by distributor listings as an ARM9 KSZx692 networking and communications microcontroller with a 400-ball BGA package. It is intended for cost-sensitive, high-performance networking equipment where an integrated processor and Ethernet controller can reduce board complexity. The KSZ9692 is a system-on-chip rather than a conventional general-purpose microcontroller. Its ARM9 core provides embedded processing capability, while the integrated Ethernet functionality supports network-facing designs. The part is associated with 10/100/1000 Ethernet communications, UART and other communications peripherals, and IPSec-related hardware security. The external program memory interface allows the system firmware and application code to be stored outside the SoC when a design requires greater memory flexibility. Key documented attributes include an ARM9 32-bit processor core, Gigabit Ethernet connectivity, external program memory support, 400-BGA packaging, 1.3 V operation, and an approximately 27 mm package dimension reported by a distributor listing. A separate source describes the family as the KSZ9692XPB, indicating closely related ordering-code and package variants. Microchip positions the KSZ9692 family for networking and communications applications, including gateways, industrial Ethernet equipment, embedded communications controllers, and secure network appliances. The KSZ9692PBI is a complex mixed-signal BGA device, so board design requires careful attention to power sequencing, high-speed routing, thermal management, and the manufacturer's reference schematic and layout guidance. The integrated Ethernet controller and ARM9 processor allow a compact architecture, but external memory, PHY connectivity, magnetics, clocking, and power design still determine whether the final equipment achieves reliable data throughput. This product data page distinguishes verified facts from parameters that require confirmation from the manufacturer datasheet. The visible sources identify the processor class, Ethernet capability, package, voltage, temperature-oriented ordering information, and application category, but they do not provide a complete pinout, detailed electrical tables, lifecycle statement, or verified replacement list. Engineers should confirm the exact KSZ9692XPB package drawing and register-level requirements before releasing a PCB.

询价 联系我们
KSZ9692XPB - ARM 922T Gigabit Networking SoC | Microchip
KSZ9692XPB

KSZ9692XPB - ARM 922T Gigabit Networking SoC | Microchip

The Microchip Technology KSZ9692XPB is a highly integrated System-on-Chip containing an ARM 922T 32-bit processor, Gigabit Ethernet and USB communications functions, and multiple I/O interfaces in a 400-BGA package. It is intended for cost-sensitive, high-bandwidth networking and communications equipment that benefits from consolidating protocol processing, network connectivity, and peripheral control into one device. An embedded communications controller is a specialized system-on-chip that combines a processor core with dedicated networking and peripheral interfaces. The KSZ9692 belongs to the broader hierarchy of embedded controllers, application-specific microcontrollers, integrated circuits, and semiconductors. Its integration can reduce the component count and board complexity of equipment requiring high-speed networking, multiple I/O controllers, and interfaces to standard peripherals. The three headline characteristics of the KSZ9692XPB are its ARM 922T 32-bit embedded processor, integrated Gigabit Ethernet and USB communications capability, and 400-BGA package. The manufacturer identifies the device as an integrated Gigabit Networking and Communications Controller. Available interface information includes Ethernet, USB, UART/USART, I2S, and EBI/EMI, although the verified source excerpts do not provide complete pin-level operating limits for every interface. The KSZ9692 family is designed for high-bandwidth networking and communications applications, where a dedicated embedded processor can manage network traffic and communications tasks alongside external interfaces. The manufacturer datasheet covers both KSZ9692PB and KSZ9692XPB, presenting them as members of the same controller family. The available verified excerpts do not establish a functional difference between the two suffix variants, so suitability should be confirmed against the complete ordering information and datasheet before substitution. Typical uses include industrial Ethernet equipment, USB-to-network systems, network interface controllers, embedded communication appliances, and cost-sensitive gateways. In such systems, the integrated processor can support protocol handling while Ethernet and USB connectivity provides links to computers, peripherals, service equipment, or networked sensors. Exact USB version, Ethernet PHY integration, clock requirements, memory interfaces, and electrical limits require confirmation from the complete manufacturer datasheet. A critical design consideration is package and signal verification. The KSZ9692XPB uses a large 400-ball BGA package, so PCB escape routing, via-in-pad or via-under-bump requirements, assembly process control, and ball-pitch compatibility must be confirmed before layout release. Because no complete pinout was present in the supplied verified excerpts, the pinout is intentionally left unavailable rather than reconstructed from memory. This page consolidates the supplied manufacturer, distributor, pricing, and cross-reference sources with application-specific engineering guidance. It separates verified facts from missing parameters, documents why verified drop-in alternatives are limited, and provides a concise basis for preliminary design evaluation before the complete datasheet and PCB constraints are reviewed.

询价 联系我们
LPC1101LVUKZ - 50MHz Cortex-M0+ 32KB MCU | NXP
LPC1101LVUKZ

LPC1101LVUKZ - 50MHz Cortex-M0+ 32KB MCU | NXP

The NXP Semiconductors LPC1101LVUKZ is a 32-bit Arm Cortex-M0+ microcontroller operating at up to 50 MHz, with 32 KB of flash memory and a 25-UFBGA WLCSP package. It belongs to the LPC1100LV scalable entry-level MCU family and is positioned for compact embedded systems that need efficient control, low power, and a small package. A microcontroller is a programmable semiconductor device that integrates a CPU core, memory, peripherals, and interface logic on one package. The Arm Cortex-M0+ architecture is a compact 32-bit core designed for cost-sensitive embedded control. In the product hierarchy, a Cortex-M0+ MCU is a microcontroller, a semiconductor, and an embedded-processing component used to sense inputs, run control logic, and manage system peripherals. Verified distributor data identifies the LPC1101LVUKZ as an ARM Cortex-M0/M0+ family MCU with a maximum CPU frequency of 50 MHz and 32 KB flash. The family description also indicates low-cost operation and ARM Cortex-M0-based design. These details make the device useful for compact control panels, embedded accessories, simple industrial modules, and low-cost consumer products where a small microcontroller package can reduce board area. The 25-UFBGA/WLCSP package is particularly relevant to space-constrained designs. Fine-pitch ball placement requires careful PCB layout, including short power and ground connections, controlled escape routing, and assembly-process compatibility. Because the supplied data does not provide the complete electrical timing, memory map, peripheral list, pin table, or package drawing, those details remain to be confirmed from NXP's current documentation before schematic capture or production release. The LPC1101LVUKZ should be considered when an engineer needs an Arm Cortex-M0+ MCU at 50 MHz with 32 KB flash in a compact WLCSP package. Verify the exact peripheral set, pin multiplexing, operating voltage, temperature range, package dimensions, and programming requirements against the manufacturer datasheet. NXP cross-reference tools can assist with device selection, but any replacement must be validated for package, pinout, memory, clock, peripheral, and software compatibility. This page combines verified distributor listings, available pricing and inventory references, manufacturer-oriented documentation links, and package-aware selection guidance for LPC1101LVUKZ evaluation.

询价 联系我们
LPC1102LVUKZ - 50MHz ARM Cortex-M0 32KB MCU | NXP
LPC1102LVUKZ

LPC1102LVUKZ - 50MHz ARM Cortex-M0 32KB MCU | NXP

The NXP Semiconductors LPC1102LVUKZ is an entry-level 32-bit ARM Cortex-M0 microcontroller operating up to 50 MHz, with 32 KB of flash memory and 8 KB of SRAM, in a 25-pin WLCSP package measuring 2.17 mm by 2.32 mm. It belongs to the LPC11xxLV family of low-cost microcontrollers for compact embedded-control designs. A microcontroller is a semiconductor device that integrates a CPU core, program memory, data memory, and peripherals into one package. The LPC1102LVUKZ combines an Arm Cortex-M0 core, general-purpose I/O, serial interfaces, timers, and communication resources for embedded systems. Its 50 MHz operating frequency provides more processing headroom than lower-frequency entry MCUs while retaining a simple architecture suitable for cost-sensitive control products. The verified distributor data identifies the part as an ARM Cortex-M0 LPC1100LV-series MCU with 32-bit processing, 50 MHz maximum frequency, 32 KB flash organized as 32K x 8, and 8 KB SRAM. The 25-WLCSP package enables compact layouts in wearables, small control modules, sensor nodes, and portable equipment. Because WLCSP assembly and inspection require specialized PCB design and manufacturing capability, designers should confirm the exact land pattern and assembly process before releasing a layout. This MCU is suited to applications that require compact digital control, serial communication, timing, and low-cost integration rather than high analog precision or large memory capacity. Its 32 KB flash limits firmware size, while 8 KB SRAM supports moderate stack, buffer, and working-memory requirements. The Cortex-M0 ecosystem also makes standard embedded tooling and library support more accessible than a proprietary architecture. Typical uses include small sensor interfaces, wearable accessories, actuator controllers, compact instrumentation, connected accessories, and low-cost embedded products. For a new design, evaluate the complete peripheral list, voltage limits, package dimensions, pin multiplexing, programming method, and operating-temperature requirements against the manufacturer datasheet before committing the PCB footprint. Designers should verify the exact pin functions and electrical limits from the NXP LPC1102 documentation rather than relying on distributor summaries. Keep power routing and decoupling close to the device, confirm exposed-pad or thermal requirements for the package, and validate firmware timing under the intended clock configuration. The LPC1102LVUKZ is best suited to compact, cost-sensitive systems whose firmware fits within 32 KB of flash and whose data working set fits within 8 KB of SRAM. This page combines verified distributor listings, package and memory details, application guidance, sourcing context, and explicit uncertainty markers. It is designed as a practical starting point for engineers comparing the LPC1102LVUKZ with other compact 32-bit microcontrollers.

询价 联系我们
LPC1102UK - 50MHz Cortex-M0 MCU with 32KB Flash | NXP
LPC1102UK

LPC1102UK - 50MHz Cortex-M0 MCU with 32KB Flash | NXP

The NXP Semiconductors LPC1102UK is a 32-bit Arm Cortex-M0 microcontroller rated for operation up to 50 MHz, with 32 KB of flash memory and 8 KB of SRAM in a 16-WLCSP package measuring 2.17 mm by 2.32 mm. It is positioned as a low-cost, low-complexity MCU for designs migrating from 8-bit and 16-bit microcontrollers to a 32-bit architecture. A microcontroller is a programmable system-on-chip that integrates a processor core, nonvolatile program memory, volatile data memory, digital peripherals, and interface controllers on one die. The LPC1102UK belongs to the LPC11xx family of Arm Cortex-M0 devices. Its compact instruction set and integrated memory support embedded control, while its 32-bit architecture provides a practical migration path from legacy 8-bit and 16-bit designs. The verified product information identifies the Arm Cortex-M0 processor, 50 MHz maximum operating frequency, 32 KB flash, 8 KB SRAM, and 16-WLCSP package. The NXP product page also describes the LPC11xx family as a low-power, low-cost family designed for 8-bit and 16-bit microcontroller replacements, with reduced code size and a scalable entry-level feature set. Compared with larger general-purpose Cortex-M devices, the LPC1102UK emphasizes simplicity, compactness, and low cost. Its 2.17 mm by 2.32 mm uncased chip package minimizes PCB area but requires assembly processes capable of handling very small pitch balls and fine board-routing features. The package page identifies this option as 16-pin WLCSP, making land-pattern and assembly verification essential before release to production. Typical uses include small sensor controllers, compact industrial modules, building-control endpoints, appliance control boards, and connected low-power products. Engineers should account for restricted memory, small-package assembly, exposed-pad or thermal considerations, and firmware complexity when selecting this device. The key design priority is to validate code size, peripheral requirements, clocking, power behavior, and PCB assembly before committing the very small footprint. Use NXP's product page and LPC1102UK datasheet as the controlling references for electrical limits, pin functions, package dimensions, and programming support. This page consolidates verified source data, technical context, procurement facts, and engineering cautions that are not presented as one unified document by the distributor listings. It helps buyers distinguish the confirmed LPC1102UK capabilities from specifications that still require direct datasheet verification.

询价 联系我们
LPC1104UK - 32-bit Cortex-M0 50MHz MCU | NXP
LPC1104UK

LPC1104UK - 32-bit Cortex-M0 50MHz MCU | NXP

NXP Semiconductors LPC1104UK is a 32-bit ARM Cortex-M0 microcontroller operating at 50 MHz, with 32 KB of flash memory and 8 KB of SRAM, in a compact 16-WLCSP package measuring 2.17 mm by 2.32 mm. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one compact device. The Cortex-M0 processor belongs to the ARM Cortex-M family of 32-bit embedded processors. Within the product hierarchy, this MCU combines a RISC processor core, embedded flash, static RAM, serial interfaces, timers, and GPIO resources for compact control systems. The verified device data identifies the LPC1104UK as a 32-bit Cortex-M0 MCU with a maximum clock frequency of 50 MHz. Its 32 KB flash organized as 32K x 8 provides program storage, while 8 KB of SRAM supplies working memory. The 16-WLCSP surface-mount package has 16 terminals and measures approximately 2.17 mm by 2.32 mm, making it suitable for highly compact embedded products when board density and assembly capability are priorities. The LPC1104 series targets low-cost control applications that benefit from 32-bit processing, a simple instruction set, efficient code execution, and integrated memory. Its operating core is identified as ARM Cortex-M0, and distributor listings classify it as a scalable entry-level MCU. Software can be developed using the LPC1100 device family package identified by Arm Keil, while firmware deployment and peripheral-level validation must be completed against the NXP datasheet. Typical uses include low-cost embedded controllers, eMetering, lighting systems, alarm systems, compact sensor nodes, and industrial or consumer products that require local processing in a very small package. The exact serial peripherals, GPIO count, timer resources, voltage limits, current consumption, and package ball assignments are not present in the supplied excerpts and should be verified in the manufacturer datasheet before schematic or firmware release. The most important design consideration is package-level verification. A 2.17 mm by 2.32 mm 16-WLCSP is not a conventional leaded package and requires land-pattern, solder-paste, stencil, reflow, and inspection validation. Engineers should also verify regulator requirements, clock strategy, reset behavior, programming access, exposed-pad treatment, and peripheral pin multiplexing from the complete datasheet. This product page consolidates verified distributor specifications, datasheet links, package constraints, and application guidance for LPC1104UK procurement and engineering evaluation. It distinguishes confirmed facts from unavailable parameters rather than inferring unverified electrical, timing, environmental, lifecycle, or compliance values.

询价 联系我们
LPC1112LVFHI33/103 - 50MHz Cortex-M0 MCU 16KB | NXP
LPC1112LVFHI33/103

LPC1112LVFHI33/103 - 50MHz Cortex-M0 MCU 16KB | NXP

The NXP Semiconductors LPC1112LVFHI33/103 is a 32-bit ARM Cortex-M0 entry-level microcontroller operating at up to 50 MHz, with 16 kB flash memory, 8 kB SRAM, and an 8-channel 10-bit ADC (advertised as 8-bit ADC mode support), housed in a 32-pin HVQFN (5x5 mm) package. A microcontroller unit (MCU) integrates a processor core, memory, and peripherals on a single chip, sitting at the top of the embedded-hierarchy ladder above plain logic ICs and below application processors. The ARM Cortex-M0 is a 32-bit core designed as an evolutionary and performance upgrade path from 8/16-bit MCUs, offering a simple instruction set and reduced code size while retaining low power and low cost. Key features of the LPC1112LVFHI33/103 include the low-voltage (LV) supply design of the LPC11xxLV family, CPU frequencies up to 50 MHz, fast general-purpose I/O, and standard serial peripherals such as UART, SPI, and I2C typical of the LPC1100LV series. The 32-HVQFN 5x5 mm footprint suits compact, cost-sensitive boards. Technically, the Cortex-M0 core executes a 56-instruction Thumb instruction set with a 32-bit architecture, delivering significantly higher efficiency than 8-bit MCUs while maintaining deterministic interrupt behavior through its nested vectored interrupt controller (NVIC). Typical applications include 8/16-bit MCU replacement in consumer appliances, motor control and sensing nodes, and battery-powered industrial accessories where low cost, low power, and 32-bit headroom are needed. Design consideration: as an LV (low-voltage) family member, verify supply-rail compatibility - the LV series operates at lower core/IO voltage domains than the standard LPC11xx, so confirm the exact operating range in the NXP datasheet before substituting standard-voltage parts. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet. Per the NXP product page, LPC1112LVFHI33 is announced End of Life (EOL), so alternatives and last-time-buy planning are covered below.

询价 联系我们
LPC1112LVFHN24/003 - 50MHz Cortex-M0 MCU 16KB Flash | NXP
LPC1112LVFHN24/003

LPC1112LVFHN24/003 - 50MHz Cortex-M0 MCU 16KB Flash | NXP

The NXP LPC1112LVFHN24/003 is an ARM Cortex-M0 microcontroller from the LPC1100LV family, delivering 50 MHz core performance with 16 KB of embedded Flash and a 24-pin HVQFN (4x4 mm) package optimized for low-voltage and space-constrained designs. It integrates 32-bit compute, 16 KB (16K x 8) Flash, up to 2 KB SRAM, a fast-mode Plus I2C-bus interface, one UART, one SPI/SSP interface, four general-purpose counters/timers, an 8-bit ADC, and up to 27 general purpose I/O pins. The LPC1100LV family is specifically engineered for applications that demand low active power and reduced supply voltage while retaining the deterministic interrupt latency of the Cortex-M0 core. An ARM Cortex-M0 microcontroller is a 32-bit processor core built around the Thumb instruction set and a von Neumann system bus, optimized for energy-efficient embedded control. In the broader taxonomy, the LPC1112LV sits within the hierarchy: Cortex-M0 -> ARM Cortex-M microcontroller family -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. The LPC1100LV sub-family extends the standard LPC1100 series with low-voltage operation, enabling direct connection to single-cell Li-ion or two-AA battery stacks without an additional boost converter. Key features of the LPC1112LVFHN24/003 include 50 MHz CPU clock, 16 KB on-chip Flash, up to 2 KB SRAM, an 8-channel/8-bit ADC, an active-high reset pin, and a System tick timer. The 24-pin HVQFN (4x4 mm) package provides a compact footprint with an exposed thermal pad to improve heat dissipation in sealed industrial enclosures. The device is built on a low-leakage CMOS process, integrating a 2-bit advanced peripheral bus matrix for deterministic peripheral access and an NVIC for standard Cortex-M0 interrupt handling. Its in-system programming (ISP) and in-application programming (IAP) support Flash updates over UART without requiring an external programmer. Typical applications include consumer battery-powered products, low-voltage sensor hubs, low-energy wireless MCU companions, portable health accessories, and small home-appliance controllers. Its low active power and compact HVQFN-24 footprint make it particularly attractive where PCB area is at a premium. When designing with this device, ensure the supply voltage is within the LPC1100LV low-voltage operating window specified in the datasheet. Because this part shares the Cortex-M0 toolchain with the larger LPC1100 family, existing SWD debug probes and CMSIS-PACK configurations can be reused with minimal change. This page synthesizes distributor pricing, drop-in alternatives and practical design notes not found in a single manufacturer document, providing a one-stop engineering and procurement reference for the LPC1112LVFHN24/003.

询价 联系我们
LPC1114LVFHI33/303 - 32KB Flash 50MHz Cortex-M0 MCU | NXP
LPC1114LVFHI33/303

LPC1114LVFHI33/303 - 32KB Flash 50MHz Cortex-M0 MCU | NXP

The NXP LPC1114LVFHI33/303 is a 32-bit ARM Cortex-M0 microcontroller operating up to 50 MHz, featuring 32 KB of flash memory and 8 KB of SRAM, housed in a 32-pin HVQFN (5x5 mm) package. An ARM Cortex-M0 microcontroller is a low-power, 32-bit processor core designed for entry-level embedded applications, offering Thumb-2 instruction efficiency and a simplified programmer's model. It sits within the microcontroller hierarchy as a subset of ARM Cortex processors, which in turn belong to the broader embedded microcontroller and system-on-chip family. The Cortex-M0 specifically targets cost-sensitive 8/16-bit replacements where higher performance, lower power, and modern toolchain support are required. The LPC11xxLV family represents NXP's low-voltage variant, allowing operation down to 1.65 V supply for battery and energy-harvesting designs. Key features of the LPC1114LVFHI33/303 include a 50 MHz maximum CPU clock, an 8-channel 10-bit ADC, two SSP/SPI peripherals, one I2C (Fast-mode), a UART, four general-purpose counter/timers, and an internal IRC oscillator trimmed to ±1 percent accuracy. The device operates over a wide supply range of 1.65 V to 1.95 V (LV core) or up to 3.6 V depending on configuration, with multiple low-power modes such as Sleep, Deep-sleep, and Power-down for battery-powered applications. On the architecture side, the LPC1114LV implements a 3-stage pipeline Cortex-M0 core with single-cycle GPIO access, NVIC supporting 32 interrupts, and a code read protection (CRP) feature for firmware security. Its memory map places flash at 0x0000 0000 and SRAM at 0x1000 0000, and a serial wire debug (SWD) port replaces the legacy JTAG for programming and on-chip debug. Typical applications include the LPC1114LVFHI33/303 driving 8/16-bit replacements such as e-metering, LED lighting controls, alarm systems, white goods motor control, simple sensor hubs, and consumer peripherals. Pairing it with a low-voltage LDO and a small Li-ion coin cell provides a compact, long-life solution for wearable and IoT edge nodes. Design consideration: keep analog and digital ground returns separated on a single-point tie at the chip's GND pad to minimize ADC offset errors. In power-down mode, current drops to sub-microamp levels but only after configuring all wake-up sources through the NVIC and the SYSCON block per the user manual. This page synthesizes distributor pricing, drop-in alternatives sourced from the same LPC11xxLV family, and practical bring-up notes extending beyond the manufacturer datasheet, helping engineers make a confident sourcing and PCB-drop-in decision.

询价 联系我们
LPC1114LVFHN24/103 - 32KB Cortex-M0 MCU 50MHz | NXP
LPC1114LVFHN24/103

LPC1114LVFHN24/103 - 32KB Cortex-M0 MCU 50MHz | NXP

The NXP LPC1114LVFHN24/103 is a 32-bit ARM Cortex-M0 microcontroller operating at up to 50 MHz with 32 kB flash memory and 8 kB SRAM, housed in a 24-pin HVQFN (4x4 mm) exposed-pad package. It belongs to the LPC1100LV family, engineered for 1.8V-class low-voltage operation. A microcontroller unit (MCU) is an integrated circuit that combines a processor core, memory, and peripherals on a single die. The Cortex-M0 is the entry-level 32-bit core in the ARM Cortex-M hierarchy, sitting above 8/16-bit MCUs in performance while offering a simple 56-instruction set, low power consumption, and reduced code size compared with legacy 8/16-bit architectures. Within the power-management and embedded-control hierarchy, the LPC11xxLV family replaces traditional 8-bit controllers in cost-sensitive designs. Key features include a 32 kB (32K x 8) on-chip flash supporting firmware updates, an 8-channel 8-bit ADC for analog sensing, industry-standard serial interfaces (UART, SPI, I2C), and CPU frequencies up to 50 MHz. The low operating voltage class of the LV family suits battery-powered and low-voltage industrial designs where 1.8V-to-2V rails are standard. Architecturally, the LPC1114LVFHN24/103 implements the ARMv6-M Thumb instruction set with NVIC interrupt handling and COTS toolchain support through ARM Keil MDK, which lists the device with the LPC1100_DFP CMSIS pack. The peripheral complement documented by NXP for the LPC11xxLV family includes GPIO, timers, and serial communication blocks tailored for 8/16-bit replacement tasks. Typical applications cited by ARM Keil and NXP for the LPC1100 series include eMetering, lighting control, alarm systems, and general 8-/16-bit application migration to 32-bit platforms. A key design consideration is lifecycle: NXP lists the LPC1114LVFHN24 as End of Life on its product page, so new designs should evaluate alternatives or last-time-buy inventory from remaining channels such as Rochester Electronics. This page synthesizes distributor pricing, same-family drop-in variants, availability data, and lifecycle guidance not consolidated in the manufacturer datasheet.

询价 联系我们
LPC1114LVFHN24/303 - 50MHz Cortex-M0 32KB MCU | NXP
LPC1114LVFHN24/303

LPC1114LVFHN24/303 - 50MHz Cortex-M0 32KB MCU | NXP

The NXP Semiconductors LPC1114LVFHN24/303 is a 32-bit ARM Cortex-M0 microcontroller with up to 32 kB flash, 8 kB SRAM, and an 8-channel 8-bit ADC, housed in a 24-pin HVQFN (4x4 mm) package and operating at CPU frequencies up to 50 MHz. A microcontroller (MCU) is a single-chip computer integrating a processor core, memory, and peripherals, used as the control element in embedded systems. Within this hierarchy, the Cortex-M0 is a 32-bit ARM core, and the LPC11xxLV family from NXP is positioned as a low-cost 32-bit replacement for 8-bit and 16-bit MCU applications, offering higher performance, lower power, and a simple instruction set with reduced code size compared to existing 8/16-bit architectures. Key features of the LPC1114LVFHN24/303 include the ARM Cortex-M0 core running at 50 MHz, 32 kB on-chip flash (32K x 8), 8 kB SRAM, and a low-voltage supply operation consistent with the LPC1100LV series designation. The compact 24-HVQFN exposed-pad package suits space-constrained designs, and peripherals such as USART, SPI/SSP, I2C, timers, and the 8-bit ADC support typical embedded connectivity and sensing tasks. The Cortex-M0 architecture uses a von Neumann structure with a 32-bit instruction set subset (56 instructions) and Thumb code density, making code smaller than comparable 8/16-bit cores while delivering deterministic interrupt handling via the Nested Vectored Interrupt Controller (NVIC). The single-cycle I/O porting and configurable pin function multiplexing on the LPC1114 allow flexible peripheral mapping on the limited 24-pin footprint. According to NXP and Arm Keil documentation, typical applications for the LPC1100LV series include 8/16-bit application migration, eMetering, lighting, alarm systems, and general embedded control. The LPC1114LVFHN24/303 fits designs needing 32-bit performance and 32 kB flash in a 4x4 mm QFN. Important design consideration: NXP lists the LPC1114LVFHN24 base part as End of Life (per the NXP product page), so verify stock and plan a replacement strategy before new designs; consult the manufacturer datasheet for exact supply voltage limits and pin mapping. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
LPC11A02UK - 50MHz ARM Cortex-M0 MCU | NXP | WLCSP-20
LPC11A02UK

LPC11A02UK - 50MHz ARM Cortex-M0 MCU | NXP | WLCSP-20

The NXP Semiconductors LPC11A02UK is a 50 MHz, 32-bit Arm Cortex-M0 microcontroller with 16 kB of Flash memory and 4 kB of SRAM, housed in a 20-WLCSP package. It is designed for compact embedded products that need efficient control processing, mixed-signal sensing, and low power operation in a very small footprint. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, and peripherals into one component. The LPC11A02UK belongs to the LPC11Axx family of low-cost 32-bit MCUs and uses the Arm Cortex-M0 architecture, which provides a compact instruction set for responsive embedded control. Its 16 kB Flash supports firmware storage, while its 4 kB SRAM provides working memory for control routines and data buffers. Key features include operation up to 50 MHz, a 1-bit ADC, a 10-bit DAC, an analog comparator, a temperature sensor, an internal voltage reference, and under-voltage lockout protection. The verified distributor information identifies the device as a WLCSP-20 packaged microcontroller with 18 I/O ports and a supply voltage range of 2.6 V to 3.6 V. These features allow the MCU to support sensing, actuator control, monitoring, and low-speed communication tasks within a compact embedded design. The LPC11A02UK uses a 32-bit Arm Cortex-M0 processor and is positioned as a low-cost member of the LPC11Axx microcontroller family. The Cortex-M0 core is suitable for deterministic, compact embedded-control code where simplicity, low silicon cost, and compact packaging matter. The device combines digital control with configurable analog and mixed-signal peripherals, allowing one MCU to supervise sensors, drive outputs, and manage local system conditions. Typical applications include battery-powered sensor nodes, compact industrial monitoring modules, consumer accessories, small motor-control subsystems, and embedded control boards. The 20-WLCSP package is especially useful where PCB area is constrained. Designers should confirm the exact ball map, exposed-pad requirements, supported peripherals, and pin multiplexing against the manufacturer datasheet before laying out a new PCB or replacing another device. This page consolidates verified manufacturer and distributor information, package details, application guidance, and purchasing considerations. Pricing and availability can change by quantity and supplier, so procurement should be confirmed against current distributor listings. For replacements, pin compatibility and peripheral equivalence must be verified rather than inferred from the family name alone. The LPC11A02UK is an active NXP product suitable for engineers seeking a compact Arm Cortex-M0 controller with integrated sensing and monitoring functions. Its principal trade-offs are small package availability, limited memory compared with larger MCUs, and the need for careful board-level validation around the 20-WLCSP footprint.

询价 联系我们
LPC11A04UK - 50MHz Cortex-M0 MCU, 32KB Flash | NXP
LPC11A04UK

LPC11A04UK - 50MHz Cortex-M0 MCU, 32KB Flash | NXP

The NXP Semiconductors LPC11A04UK is a low-cost, 32-bit Arm Cortex-M0 microcontroller operating up to 50 MHz, with 32 KB of Flash, 8 KB of SRAM, and 4 KB of EEPROM in a 20-WLCSP package measuring 2.55 mm by 2.55 mm. The verified distributor data identifies an 18-I/O device and configurable analog or mixed-signal resources for compact embedded control designs. A microcontroller is a programmable system-on-chip that integrates a CPU core, nonvolatile program memory, working memory, peripherals, and input/output into one package. The LPC11A04UK belongs to the MCU, embedded processor, semiconductor, and Arm Cortex-M0 hierarchy. It targets cost-sensitive control, sensing, communication, and actuator functions where deterministic low-power behavior and compact packaging are valuable. The LPC11A04 family operates at CPU frequencies up to 50 MHz and includes a Nested Vectored Interrupt Controller, a system tick timer, Serial Wire Debug, an ISP and IAP-capable on-chip bootloader path, and up to 16 kB of boot ROM according to the verified Keil device record. Its memory combination supports compact firmware, working state, and retained parameters without requiring external memory for many designs. NXP describes the LPC11Axx family as a scalable entry-level MCU family with a low-cost 32-bit instruction set and software-configurable analog and mixed-signal subsystems. The architecture is suitable for small control loops, but designers should verify the exact peripheral set, clock limits, pin multiplexing, and electrical limits against the official device documentation before releasing a PCB. Typical uses include low-power sensor nodes, simple motor-control helpers, compact industrial controls, consumer accessories, and connected embedded products. The 20-WLCSP package supports dense layouts, while its small ball pitch and exposed thermal and routing complexity make careful PCB assembly and inspection important. The principal design trade-off is integration versus inspection risk. The LPC11A04UK consolidates processing, memory, GPIO, and configurable analog functions into a tiny package, reducing board area but increasing sensitivity to pad geometry, solderability, and layout quality. This page combines the supplied manufacturer and distributor records, pricing evidence, package details, design guidance, and verified cross-reference findings. It also distinguishes documented facts from missing technical data instead of estimating electrical limits, pin functions, or drop-in alternatives that the supplied sources do not establish.

询价 联系我们
LPC11C14FBD48/301 - 32KB Flash Cortex-M0 MCU w/ CAN | NXP
LPC11C14FBD48/301

LPC11C14FBD48/301 - 32KB Flash Cortex-M0 MCU w/ CAN | NXP

The NXP LPC11C14FBD48/301 is an ARM Cortex-M0 based 32-bit microcontroller running at up to 50 MHz, with 32 KB of on-chip flash, 8 KB of SRAM, and an integrated C_CAN controller, housed in a 48-pin LQFP (7x7 mm) package. It belongs to the LPC1100 series, designed as a low-cost upgrade path for 8/16-bit MCU applications, offering higher performance with a simple Thumb/Thumb-2 instruction set and reduced code size compared to legacy architectures. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (flash), volatile data memory (SRAM), and peripherals such as timers, communication interfaces, and analog blocks into one package. MCUs sit at the bottom of the embedded computing hierarchy: MCU -> microcontroller -> embedded processor -> semiconductor device. The Cortex-M0 class represents the smallest, lowest-power variant of the ARMv6-M architecture, with deterministic interrupt handling that makes it well-suited for real-time control. The on-chip C_CAN conforms to the ISO 11898-1 CAN 2.0B standard, eliminating the need for an external CAN transceiver controller in bus-node designs. Key features include a 50 MHz Cortex-M0 core with single-cycle multiplier, 32 KB flash with In-System Programming (ISP) and In-Application Programming (IAP), 8 KB SRAM, a 12 MHz internal RC oscillator trimmable to 1% accuracy, an integrated C_CAN 2.0B controller, one SSP/SPI, one I2C, one UART, four general-purpose timers, a 10-bit ADC with up to 8 input channels, and a windowed watchdog timer. Power consumption is rated at approximately 10 mA active and 1 mA in deep-sleep mode at 3.3 V. The architecture uses a 3-stage pipeline with the ARMv6-M Thumb instruction set. Code density is significantly improved over 8/16-bit cores, allowing more functionality in the same 32 KB flash budget. The integrated C_CAN block uses 256-byte message RAM, supporting both standard (11-bit) and extended (29-bit) identifiers, which simplifies fieldbus node designs. The 12 MHz IRC can be trimmed in software to within 1% across the full operating range, often eliminating the need for an external crystal. Typical applications include CAN node endpoints in industrial automation, e-metering and smart metering, LED lighting controllers, alarm system panels, white goods, sensor hubs, and low-cost building-automation gateways. The integrated CAN controller is the standout feature in this price/performance class - the part is positioned wherever an 8-bit MCU is being replaced but a CAN interface is also required. When designing with this MCU, place a 100 nF decoupling capacitor adjacent to each VDD pin and connect all VSS pins to a solid ground plane to reduce digital switching noise coupling into the ADC. The CAN TXD/RXD lines still require an external 3.3 V CAN transceiver such as the TJA1050 or SN65HVD230 to drive the bus. This page synthesizes distributor pricing, drop-in LPC11xx alternatives, design notes, and application guidance that is not consolidated in the manufacturer datasheet, helping engineers and procurement teams evaluate the LPC11C14FBD48/301 in a single view.

询价 联系我们
LPC11E66JBD48E - 50MHz Cortex-M0+ MCU 64KB Flash | NXP
LPC11E66JBD48E

LPC11E66JBD48E - 50MHz Cortex-M0+ MCU 64KB Flash | NXP

The NXP LPC11E66JBD48E is a 32-bit ARM Cortex-M0+ microcontroller operating at up to 50 MHz CPU frequency, integrating 64 KB of flash, 12 KB of SRAM, and 4 KB of on-chip EEPROM, housed in a 48-pin LQFP (7x7 mm) package. It is part of the LPC11Exx family, a low-cost 32-bit MCU series designed as a stepping stone from 8/16-bit architectures to modern Cortex-M performance with a simple instruction set that minimizes code size. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, data memory, peripherals, and I/O. The ARM Cortex-M0+ is ARM's smallest and most energy-efficient Cortex-M core, designed for deterministic embedded control. Loaders live in the broader hierarchy: Cortex-M0+ -> ARM Cortex-M -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. The LPC11Exx family targets applications transitioning from 8/16-bit MCUs by providing modern performance with familiar low-pin-count packages. Key features include a 12-bit ADC for sensor digitization, multiple serial interfaces (USART, SPI, I2C), PWM outputs for motor or LED control, and configurable GPIO. The integrated EEPROM (4 KB) eliminates the need for an external non-volatile memory chip for parameter storage, lowering BOM count. The 50 MHz CPU frequency provides ample headroom for protocol stacks and real-time control loops. Architecturally, the LPC11E66 uses the Cortex-M0+ core paired with a configurable AHB bus matrix, low-power peripherals, and a programmable ROM-based boot loader that supports in-system programming via UART or USB ISP. This combination allows field firmware upgrades without external programmers, which is valuable for deployed industrial and consumer products. Typical applications include home appliances, white goods, motor control peripherals, building automation nodes, low-cost sensor hubs, and consumer electronics requiring USB or CAN connectivity through on-chip interfaces. The wide operating voltage range (typically 1.8V-3.6V core) supports battery-powered devices. When designing with this MCU, ensure the decoupling network uses 100 nF X7R ceramics on each VDD/VDDA pin placed within 2 mm of the pad. Leave the ISP entry pin accessible (typically PIO0_1) to enable in-field firmware updates without disassembly. This page synthesizes distributor pricing, drop-in alternatives from NXP LPC11Exx family, and practical design notes not consolidated in the manufacturer datasheet, giving procurement and engineering teams a single reference for the LPC11E66JBD48E.

询价 联系我们
LPC11E67JBD48K - 32-Bit 50MHz Cortex-M0+ MCU | NXP
LPC11E67JBD48K

LPC11E67JBD48K - 32-Bit 50MHz Cortex-M0+ MCU | NXP

NXP Semiconductors LPC11E67JBD48K is a 32-bit ARM Cortex-M0+ microcontroller operating up to 50 MHz, with 128 KB of Flash memory and a 48-LQFP 7 x 7 mm package. It belongs to the LPC11Exx family, a scalable entry-level MCU range designed to replace 8-bit and 16-bit designs while retaining a simple instruction set and efficient code footprint. The verified manufacturer listing identifies this orderable variant as active. A microcontroller is an integrated circuit containing a processor core, program Flash, data memory, peripherals, and interface logic on one semiconductor device. The ARM Cortex-M0+ core provides a compact instruction set and deterministic embedded-control architecture. Within the product hierarchy, the LPC11E67JBD48K is an ARM-based microcontroller, an embedded processor, and a semiconductor intended for cost-sensitive control applications. The LPC11E67JBD48K combines a maximum 50 MHz operating frequency with 128 KB of Flash organized as 128K x 8. This combination supports firmware storage while avoiding the memory cost and board area of a larger microcontroller package. The 48-LQFP 7 x 7 mm package offers a surface-mount solution with a comparatively compact body, although its lead pitch must be accommodated by the PCB land pattern and assembly process. The LPC11Exx family also includes devices with up to 256 kB Flash, 36 kB SRAM, and 4 kB EEPROM according to the verified datasheet listing. A 12-bit ADC is identified in the same source. Device-specific ADC, SRAM, EEPROM, clock, and peripheral details must be confirmed in the manufacturer datasheet before assigning pins or calculating firmware resource requirements. Typical uses for this microcontroller class include compact industrial controllers, building and access-control equipment, appliance controls, sensing nodes, and low-cost embedded products. The 50 MHz Cortex-M0+ performance is useful for responsive control loops and moderate protocol handling, while the 128 KB Flash capacity allows application firmware and configuration data to be stored locally. Designers should verify the exact LPC11E67JBD48 pin assignments, peripheral multiplexing, clock limits, decoupling requirements, and exposed-pin treatment in the NXP datasheet. The verified web results do not provide a complete public pin table, so this record does not infer pin names or provide a fabricated package diagram mapping. PCB design and firmware bring-up should also account for the LQFP lead geometry rather than a leadless QFN footprint. This product record combines current NXP lifecycle information, distributor inventory and pricing evidence, family-level technical data, strict data-availability markers, and procurement guidance. It distinguishes verified device facts from parameters that still require confirmation, helping engineers avoid treating broader LPC11Exx family capabilities as guaranteed LPC11E67JBD48K specifications.

询价 联系我们
LPC11E67JBD64E - 50MHz Cortex-M0+ 128KB MCU | NXP
LPC11E67JBD64E

LPC11E67JBD64E - 50MHz Cortex-M0+ 128KB MCU | NXP

NXP Semiconductors LPC11E67JBD64E is a 32-bit ARM Cortex-M0+ microcontroller with a 50 MHz maximum CPU frequency, 128KB of flash memory, and 20KB of SRAM in a 64-pin LQFP package measuring 10 mm by 10 mm. It belongs to the LPC11Exx scalable entry-level MCU family, combining an efficient ARM Cortex-M0+ core with embedded flash, SRAM, and mixed-signal peripherals in one compact surface-mount package. An ARM Cortex-M0+ microcontroller is a compact embedded-processing device used to execute firmware, read sensors, control outputs, and manage communication peripherals. The LPC11Exx family sits within the broader hierarchy of microcontroller, embedded processor, semiconductor, and embedded-control systems. Its 32-bit architecture provides an efficient platform for cost-sensitive products requiring deterministic real-time control without the resources of a higher-performance Cortex-M processor. The LPC11E67JBD64E provides 128KB of flash for program storage and 20KB of SRAM for data, stack, and working memory. Its maximum CPU frequency is 50 MHz. The device is supplied in a 64-LQFP package, providing 64 external pins for power, ground, resets, clock inputs, and peripheral connections. The verified distributor information also identifies the device as a 3.3 V part and as a member of the LPC11Exx family. Detailed GPIO allocation, operating-temperature limits, and individual peripheral characteristics remain subject to the manufacturer datasheet. The ARM Cortex-M0+ core supports a compact instruction set optimized for embedded control, while the integrated memory allows firmware and working data to share a single package and PCB footprint. This integration reduces component count and simplifies board routing compared with a discrete processor-plus-memory implementation. The 50 MHz operating rate provides useful headroom for protocol handling, digital control loops, and supervisory tasks while maintaining a low-complexity architecture. Typical uses include industrial control modules, sensor-hub boards, communication equipment, building automation, appliance controllers, and compact embedded data-acquisition products. The 128KB flash capacity is suitable for moderate firmware images, while 20KB SRAM supports networking stacks and control buffers without requiring external memory. Its 64-LQFP package also makes the device accessible for prototype assembly and conventional surface-mount manufacturing. Designers should verify the complete pin assignment, peripheral multiplexing, and electrical limits against the manufacturer datasheet before layout release. The 3.3 V supply requirement should be paired with appropriate decoupling and signal-level planning for connected modules. Because exact GPIO, timing, temperature, and qualification data were not included in the verified results, those values should not be inferred from the family description alone. This product record combines verified distributor specifications, official manufacturer identification, package information, sourcing references, and engineering-focused selection guidance. It also distinguishes the LPC11E67JBD64E from higher-memory family variants and documents the limited number of confirmed pin-compatible alternatives rather than presenting unverified substitutes as drop-in devices.

询价 联系我们
LPC11U66JBD48E - 50MHz Cortex-M0+ 64KB MCU | NXP
LPC11U66JBD48E

LPC11U66JBD48E - 50MHz Cortex-M0+ 64KB MCU | NXP

NXP Semiconductors LPC11U66JBD48E is a 32-bit Arm Cortex-M0+ microcontroller rated for operation up to 50 MHz, with 64 KB of flash memory in a 48-pin LQFP 7 x 7 mm package. It belongs to the LPC11Uxx family of low-cost, energy-efficient microcontrollers designed as scalable replacements for conventional 8-bit and 16-bit embedded systems. A microcontroller is a programmable semiconductor that integrates a CPU core, program memory, data memory, peripherals, and communication interfaces on one device. The Cortex-M0+ core provides a simple instruction set and compact code footprint, while the LPC11Uxx family combines this processing efficiency with flexible low-power features for embedded control, sensing, and communications equipment. The LPC11U66 provides 64 KB of flash, 12 KB of SRAM, and a maximum CPU frequency of 50 MHz. Its flexible peripheral set is intended to replace several discrete components in cost-sensitive embedded products. The 48-LQFP package exposes the integrated communications and general-purpose peripherals required by protocols, sensors, human-interface equipment, and low-power control systems. The Arm Cortex-M0+ architecture also supports efficient event-driven firmware, helping developers balance processing performance, code density, and energy use. Compared with an 8-bit MCU, the 32-bit processor provides a wider address space and more capable interrupt-driven control. Compared with higher-end Cortex-M systems, the LPC11U66 maintains a low-cost positioning without abandoning 32-bit software development tools. Typical uses include compact industrial controllers, connected sensor nodes, building-control modules, appliance control boards, communications equipment, and embedded access devices. The 48-LQFP package is appropriate for designs that need a moderate number of externally routed pins and a conventional leaded footprint that is easier to inspect and assemble than very fine-pitch packages. Designers should verify the complete pin assignment, peripheral multiplexing, clock configuration, and power requirements against the NXP datasheet before layout release. A stable decoupling network and correct programming-tool configuration are essential for reliable operation. The manufacturer product page identifies LPC11U66JBD48 as active, while distributor listings provide sourcing and packaging information. This page consolidates verified manufacturer information, distributor availability, practical selection guidance, and same-package alternatives for engineers evaluating the LPC11U66JBD48E. It also distinguishes confirmed source data from parameters that still require verification against the full manufacturer datasheet.

询价 联系我们
LPC11U67JBD48E - 50MHz 128KB Flash MCU | NXP | USB Cortex-M0+
LPC11U67JBD48E

LPC11U67JBD48E - 50MHz 128KB Flash MCU | NXP | USB Cortex-M0+

NXP Semiconductors LPC11U67JBD48E is a 32-bit ARM Cortex-M0+ microcontroller operating up to 50MHz, with 128KB of Flash memory, 20KB of SRAM, USB connectivity, and a 12-bit ADC in a 48-LQFP (7x7) package. It is designed for cost-sensitive embedded systems that need efficient 32-bit control, flexible peripherals, and USB communication without the power and complexity of a higher-performance Cortex-M core. The LPC11Uxx family belongs to the microcontroller hierarchy: MCU > embedded processor > Arm Cortex-M0+ microcontroller > low-power embedded control. The Cortex-M0+ architecture provides a simple instruction set and efficient code density while retaining a 32-bit processing model. At up to 50MHz, the LPC11U67JBD48E is suitable for connected peripherals, human-interface systems, sensor controllers, and compact consumer or industrial equipment. Verified listings identify 128KB Flash, 20KB SRAM, USB, and a 12-bit ADC. The 48-LQFP (7x7) package provides a conventional leaded footprint that can simplify assembly and prototyping compared with a fine-pitch ball grid array. The 2.4V to 3.6V operating range supports common 3.3V system rails, although the complete electrical limits must be confirmed in the manufacturer datasheet before final design release. The USB capability makes the device useful for USB-to-serial adapters, configuration interfaces, HID peripherals, data acquisition controllers, and service ports. Its ADC supports applications that monitor analog sensors or industrial inputs without requiring a separate converter. The combination of 128KB Flash and 20KB SRAM gives embedded software room for protocol stacks, control logic, buffers, and application code. A typical design places the MCU beside its USB connector, 3.3V regulator, decoupling capacitors, crystal or clock source, and application peripherals. Keep USB differential routing short, controlled-impedance, and away from noisy switching nodes. Confirm oscillator, reset, USB, and peripheral pin assignments against the official datasheet before PCB routing. This page combines verified distributor specifications, sourcing information, application guidance, and same-footprint alternatives for engineering evaluation.

询价 联系我们
LPC11U67JBD64E - 50MHz Cortex-M0+ 128KB MCU | NXP
LPC11U67JBD64E

LPC11U67JBD64E - 50MHz Cortex-M0+ 128KB MCU | NXP

The NXP LPC11U67JBD64E is a 32-bit ARM Cortex-M0+ microcontroller operating at up to 50 MHz, with 128 KB of flash memory and a 64-lead LQFP package measuring 10 mm by 10 mm. The LPC11U67JBD64E belongs to NXP's LPC11Uxx scalable entry-level microcontroller family, combining an economical embedded processor with integrated USB and other connectivity-oriented peripherals. A microcontroller is a semiconductor that integrates a CPU core, memory, peripherals, and communication interfaces into one device. The ARM Cortex-M0+ core provides a compact, energy-efficient architecture for embedded control, while the LPC11Uxx family sits within the broader hierarchy of microcontroller, embedded processor, and semiconductor products. Its 50 MHz operating frequency supports responsive control loops and communication handling without requiring a high-end application processor. The verified device data identifies a 32-bit ARM Cortex-M0+ processor, 128 KB (128K x 8) flash, and a 64-LQFP (10 x 10 mm) package. The E suffix is retained as part of the exact orderable MPN. NXP describes the family as scalable and entry-level, indicating suitability for designs that need broad peripheral integration while controlling system complexity, board area, and cost. Compared with larger Cortex-M microcontrollers, the LPC11U67JBD64E provides a focused 50 MHz Cortex-M0+ platform with 128 KB of embedded flash in a 10 mm square LQFP. The 64-pin package offers more external interface options than smaller lead-count packages, making it useful when a design requires both USB connectivity and additional I/O. Exact SRAM capacity, voltage range, peripheral inventory, and electrical limits require confirmation in the manufacturer datasheet. Typical applications include USB-connected control devices, USB-to-serial adapters, human-interface-interface controllers, compact industrial controllers, instrument-panel controllers, and embedded USB peripherals. The 64-pin package can support a mix of communication, logic, and discrete I/O, while the Cortex-M0+ core handles protocol stacks, sampling, and supervisory tasks in a single device. Designers should verify the exact pin assignments, USB electrical requirements, decoupling network, clock configuration, and exposed programming/debug interfaces against the manufacturer datasheet before layout release. PCB traces, connectors, and protection components must be designed for the device's USB and power specifications. Because no complete public pinout was included in the supplied verified data, no pin-level substitutions should be inferred from this page. This product record combines exact distributor pricing and availability information, same-package family comparisons, and practical engineering guidance. It distinguishes verified facts from parameters that still require datasheet confirmation, helping engineers source the exact LPC11U67JBD64E without confusing a related LPC11E-series device with a guaranteed drop-in replacement.

询价 联系我们