ADM211EARS - 4/5 RS-232 Transceiver, 200 kbps | Analog Devices
料号: ADM211EARS ✗ 停产ADM211EARS 概述
An RS-232 transceiver is a bidirectional interface IC that converts logic-level UART signals into RS-232 line levels and converts received RS-232 levels back into CMOS-compatible logic. The ADM211EARS belongs to the broader hierarchy of RS-232 interface transceivers, line drivers, line receivers, and communications interface ICs. Its multi-channel arrangement allows one package to carry four outgoing data channels and five incoming channels, reducing the component count in multi-port equipment.
Key features include four drivers, five receivers, operation from a single 5 V rail, and data rates up to 200 kbps. The shutdown control disables the charge pump, transmitters, and receivers, allowing the interface to reduce power consumption when communication is inactive. Analog Devices identifies the family as conforming to the EIA-232-E and CCITT V.28 specifications and as suitable for environments where a 12 V supply is unavailable.
The ADM211EARS uses the ADM2xxE interface architecture for robust point-to-point RS-232 links. Its line-facing protection is specified at ±15 kV ESD, making it applicable to equipment whose serial ports may be connected externally or through long cable runs. The interface operates from 5 V, allowing it to share a common supply rail with CMOS logic in many embedded and industrial control systems.
Typical uses include industrial serial controllers, point-of-sale terminals, test equipment, data acquisition systems, and multi-channel RS-232 port expansion. The four drivers and five receivers make the part especially useful where a system has more peripheral serial links than a single UART can support. Because the part is obsolete, new designs should verify availability and consider a listed parametric equivalent before committing a new design to this exact suffix.
For layout, route each RS-232 line directly to its corresponding connector-side network and place the specified 0.1 µF charge-pump capacitor close to the device. Keep logic-side traces away from cable-side inputs, and confirm the shutdown-control polarity and timing against the ADM211E datasheet before enabling the interface in firmware.
This page consolidates the ADM211EARS lifecycle position, verified equivalent candidates, package information, interface parameters, and practical integration guidance so engineers can evaluate an obsolete 28-SSOP transceiver without repeating the same cross-reference work.
直接替换替代料: ADM211EARS ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ADM211EARS (相同外形与封装尺寸) ——差异在于 Maximum Data Rate, Package, Product Type.
ADM211ARSZ
✅ 直接替换联系询价
查看数据手册 →ADM211EARSZ
✅ 直接替换联系询价
查看数据手册 →ADM211EARS 规格参数
| Product Type | RS-232 transceiver |
| Driver Count | 4 drivers |
| Receiver Count | 5 receivers |
| 电源电压 | 5 V |
| Maximum Data Rate | 200 kbps |
| Interface Standard | EIA-232-E and CCITT V.28 |
| 封装 | 28-lead SSOP |
| 安装类型 | Surface mount |
| ESD Protection | ±15 kV |
| Charge-Pump Capacitor | 0.1 µF |
| Shutdown Function | Disables the charge pump, transmitters, and receivers |
| EMI/EMC Compliance | EMI/EMC-compliant |
| 引脚数 | 28 pins |
ADM211EARS 28-lead ssop 引脚配置指南
ADM211EARS(28-lead ssop 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ADM211EARS.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADM211EARS 适用于 6 应用s: Industrial Serial Port Expansion, Point-of-Sale Terminal Interface, Data Acquisition and Test Equipment, Legacy Computer Serial Backplane, Instrument Communication Hub, Maintenance of Legacy RS-232 Equipment.
Industrial Serial Port Expansion
The ADM211EARS fits legacy industrial controllers that need more RS-232 links than a single UART can provide. Its four drivers and five receivers allow one 28-SSOP device to manage four outbound channels while monitoring a fifth inbound signal, reducing the number of separate interface packages on the board. Operation from one 5 V rail simplifies system partitioning, and the 200 kbps rate supports both standard baud-rate links and faster legacy transfers. The ±15 kV ESD protection is particularly valuable when the ports connect to removable cables or external equipment. For a maintenance design, retain the original pin assignments and verify the shutdown behavior against the Analog Devices ADM211E documentation.
推荐
Point-of-Sale Terminal Interface
The ADM211EARS is appropriate for point-of-sale equipment that connects several peripherals through legacy RS-232 ports. Four driver outputs can support receipt printers, scanners, or other peripherals that transmit data toward the terminal, while five receiver inputs allow the controller to receive responses from multiple devices. The single 5 V supply allows the interface to operate alongside CMOS controller logic, while 200 kbps performance covers conventional serial transactions. The shutdown function can reduce power use during idle periods, provided firmware observes the manufacturer timing requirements. Because the exact ADM211EARS suffix is obsolete, new point-of-sale platforms should evaluate the currently documented equivalent rather than designing around an unsupported part number.
推荐
Data Acquisition and Test Equipment
The ADM211EARS suits legacy laboratory and test systems that must communicate with several RS-232 instruments. Four transmit channels can carry commands toward separate test platforms, and five receive channels can collect responses or status information. Its 200 kbps maximum rate is more than sufficient for instruments using common UART baud rates, while the 5 V-only architecture simplifies integration with embedded controller boards. Shutdown provides a means to disable the interface and its charge pump when measurements are complete. External connectors should include suitable protection and grounding practices in addition to the device’s ±15 kV ESD rating. Confirm channel polarity and enable timing in the manufacturer pin and timing tables before connecting powered test equipment.
推荐
Legacy Computer Serial Backplane
The ADM211EARS can support service and control ports on legacy computer, server, and peripheral equipment that uses multiple RS-232 channels. Four drivers and five receivers provide a concentrated interface for configuration links, diagnostic ports, and auxiliary equipment connections. The 200 kbps capability covers short control traffic and conventional serial console traffic without requiring a separate 12 V rail. A single 5 V supply is useful in equipment where logic rails already exist and board space is constrained. The shutdown mode lets the controller disable all transmitters, receivers, and the charge pump during inactive periods. Maintain the original connector-side routing and avoid long unprotected traces near high-energy switching nodes to preserve the intended EMI/EMC behavior.
推荐
Instrument Communication Hub
The ADM211EARS is useful in a communication hub that centralizes RS-232 connections for remote sensors, laboratory instruments, or service equipment. The receiver surplus allows one additional incoming channel to be monitored without adding another package, while the 200 kbps rate supports many conventional instrument protocols. The interface’s single 5 V requirement simplifies powering in compact controller assemblies, and the shutdown control can isolate the interface during firmware updates or bus idle periods. The ±15 kV ESD protection adds defense at connector-adjacent circuits, although cable routing and grounding remain essential parts of a reliable implementation. Use the manufacturer’s recommended application circuit and charge-pump capacitor placement to minimize emissions and maintain stable line levels.
推荐
Maintenance of Legacy RS-232 Equipment
The ADM211EARS is most directly applicable to repair and component-replacement work on legacy RS-232 equipment that uses the exact 28-SSOP footprint. Its four-driver, five-receiver arrangement and 5 V supply simplify like-for-like board maintenance, particularly for equipment with multiple serial accessories. The documented shutdown function and 200 kbps rate match the established interface behavior expected by older control firmware. Because the suffix is obsolete, traceable stock may be limited, so procurement should identify the exact package and marking requirements. Any substitute must be checked against the manufacturer pin descriptions for driver outputs, receiver inputs, shutdown polarity, ground connections, and the charge-pump capacitor pin before installation.
推荐
推荐产品汇总
工程参考数据: ADM211EARS ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ADM211ARSZ | ADM211EARSZ |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 28-SSOP | 28-SSOP | 28-SSOP |
| Product Type | 4/5 RS-232 transceiver | RS-232 interface transceiver | RS-232 interface transceiver |
| Driver Count | 4 drivers | 4 drivers | 4 drivers |
| Receiver Count | 5 receivers | 5 receivers | 5 receivers |
| Supply Voltage | 5 V | 5 V | 5 V |
| Interface Standards | EIA-232-E and CCITT V.28 | EIA-232-E and CCITT V.28 | EIA-232-E and CCITT V.28 |
关键差异点
- Four transmit channels in one multi-channel interface package (对比 MAX3221IPWR)
- Documented parametric relationship for obsolete-board replacement (对比 ADM211ARSZ)
- Higher channel count than a single-port RS-232 transceiver (对比 TJA1057GTK/3Z)
- Single-supply RS-232 operation with integrated control (对比 MAX3221CDBR)
设计说明
Place the specified 0.1 µF charge-pump capacitor close to the ADM211EARS charge-pump pin and follow the Analog Devices ADM211E recommended application layout. Keep the four driver outputs and five receiver inputs on the connector side of the board, and place the logic-side UART connections on the opposite side. This separation reduces capacitive coupling between cable-attached lines and low-level digital signals while preserving a short return path to ground.
Do not assume that every RS-232 transceiver with a similar channel count is pin-compatible. Verify driver-output positions, receiver-input positions, ground pins, shutdown polarity, and the charge-pump capacitor connection against the manufacturer pin descriptions. The ADM211ARSZ is the closest documented parametric equivalent for the ADM211EARS, but an approval still requires schematic-level comparison against the 28-SSOP footprint and the original board’s connector wiring.
The device provides ±15 kV ESD protection, but connector protection still depends on correct board layout and cable practices. Keep RS-232 traces short, route them away from switching nodes and high-current power paths, and use a continuous ground reference. Apply the manufacturer’s recommended charge-pump capacitor placement because an extended charge-pump loop can increase emissions and reduce margin in EMI-sensitive equipment.
The ADM211EARS uses a single 5 V supply, so route a local decoupling network to the device according to the recommended application circuit. Enable the shutdown control only after pending transmissions have completed, and restore it using the timing specified by Analog Devices. Shutdown disables the charge pump, transmitters, and receivers, making it useful for reducing consumption in equipment that spends substantial time with unused serial ports.
合规信息
Analog Devices describes the ADM2xxE family as compliant with the EU EMC directive. The ADM211EARSZ comparison record refers to RoHS compliance, but no specific compliance statement for the ADM211EARS suffix was established, so the affected fields remain unknown. AEC-Q100 qualification does not apply to this non-automotive interface transceiver.