ADM234LANZ - 100kbps Quad RS-232 Driver | Analog Devices
料号: ADM234LANZ ✓ 量产中ADM234LANZ 概述
An RS-232 line driver is a communications interface integrated circuit that converts logic-level signals from a host, controller, or data-acquisition system into bipolar voltage levels suitable for transmission over a serial link. It belongs to the interface IC hierarchy, specifically the line-driver and transceiver class used to bridge digital logic and legacy serial communication ports.
The ADM234LANZ provides four driver channels, a maximum supply voltage of 5.5 V, CMOS technology, and a 100 kbps maximum data rate. Its industrial temperature grade supports use in factory automation, industrial controls, instrumentation, and embedded equipment where RS-232 compatibility must coexist with a modern single-supply architecture. The through-hole PDIP package also favors repairable industrial assemblies and designs assembled with conventional DIP sockets.
Each driver channel provides the electrical voltage translation required for RS-232 signaling, while the integrated charge-pump circuitry generates the positive and negative transmitter levels from the +5 V supply. This architecture reduces the external component count compared with a discrete RS-232 implementation and avoids separate power rails for the interface. Designers should still treat the driver outputs as differential-voltage, bipolar signaling nodes rather than ordinary CMOS logic outputs.
Typical applications include RS-232 links in industrial controllers, laboratory instruments, barcode and test equipment, legacy data-collection systems, and service interfaces for embedded machinery. The device is particularly suitable when a modern controller has a 5 V UART but the peripheral connection still requires EIA-232-E levels. Its four channels support several independent transmit paths where the system needs more than one serial endpoint.
For reliable implementation, place the driver close to the connector or protected board edge, route each RS-232 output as a differential pair, and provide the supply and ground connections required by the Analog Devices datasheet. Add appropriate surge and ESD protection when the cable leaves the enclosure, and account for the non-inverting logic thresholds and slew behavior when designing system-level timing.
This page consolidates the exact ADM234LANZ electrical ratings, verified package information, sourcing guidance, cross-reference findings, and practical implementation considerations. It also distinguishes ordering and package variants from true pin-compatible replacements so engineers can make a controlled substitution without assuming that every similar RS-232 part is electrically identical.
直接替换替代料: ADM234LANZ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ADM234LANZ (相同外形与封装尺寸) ——差异在于 Package, Product Type, Maximum Data Rate, DC-DC Converter, Supply Voltage.
ADM234LARZ
✅ 直接替换📋 参考替代料(不在目录中)
ADM234LJNZ
✅ 直接替换联系询价
查看数据手册 →ADM234LAQ
✅ 直接替换联系询价
查看数据手册 →ADM234LAR
✅ 直接替换联系询价
查看数据手册 →MAX234EPE+
✅ 直接替换📋 参考替代料(不在目录中)
ADM234LANZ 规格参数
| Product Type | Quad RS-232 line driver |
| Driver Channel Count | 4 channels |
| Receiver Channel Count | 0 channels |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Maximum Supply Voltage | 5.5 V |
| Maximum Data Rate | 100 kbps |
| Technology | CMOS |
| Interface Standard | EIA-232-E and V.28 |
| 封装 | PDIP-16, MO-095AC |
| Terminal Count | 16 terminals |
| 安装类型 | Through-hole |
| Package Shape | Rectangular |
| Temperature Grade | Industrial |
| 数据速率 | 100 kbps |
ADM234LANZ 引脚配置
| 引脚 1 | R1OUT — Receiver 1 output |
| 引脚 2 | R2OUT — Receiver 2 output |
| 引脚 3 | R3OUT — Receiver 3 output |
| 引脚 4 | R4OUT — Receiver 4 output |
| 引脚 5 | T1IN — Driver 1 input |
| 引脚 6 | T2IN — Driver 2 input |
| 引脚 7 | T3IN — Driver 3 input |
| 引脚 8 | T4IN — Driver 4 input |
| 引脚 9 | GND — Ground |
| 引脚 10 | T4OUT — Driver 4 output |
| 引脚 11 | T3OUT — Driver 3 output |
| 引脚 12 | T2OUT — Driver 2 output |
| 引脚 13 | T1OUT — Driver 1 output |
| 引脚 14 | V+ — Positive supply |
| 引脚 15 | ON — Power shutdown control |
| 引脚 16 | GND — Ground |
典型应用
ADM234LANZ 适用于 6 应用s: Industrial Controller RS-232 Port, Laboratory Test Instrument Interface, Data Acquisition System, Legacy Equipment Retrofit, Barcode and Identification Equipment, Embedded Service and Configuration Port.
Industrial Controller RS-232 Port
The ADM234LANZ fits industrial controllers that retain an EIA-232-E or V.28 service port while their logic circuitry operates from +5 V. Its four driver channels can serve independent serial outputs, while the 4.5 V to 5.5 V supply range eliminates the need for separate ±12 V rails. The 100 kbps rate is adequate for configuration consoles, legacy peripherals, and short-distance supervisory links. Keep each transmitter route paired with the interface ground and place external protection near connectors exposed to industrial cable transients.
推荐
Laboratory Test Instrument Interface
Test instruments commonly expose RS-232 for legacy analyzers, fixtures, and service computers, and the ADM234LANZ supplies four single-ended-to-bipolar driver channels without external ±12 V power. A 100 kbps ceiling is appropriate for command traffic, status reporting, and low-speed measurement data rather than continuous high-bandwidth transfers. The PDIP-16 package supports prototype boards and repairable laboratory equipment. Place protection at the D-sub connector and keep analog measurement grounds separate from RS-232 return-current paths to prevent cable transients from corrupting readings.
推荐
Data Acquisition System
The ADM234LANZ can provide legacy acquisition systems with multiple outbound RS-232 paths from a +5 V controller. Its four drivers suit multi-channel instrument trigger, status, and configuration outputs, with the 100 kbps rate supporting command and control traffic. Because the part contains transmitters but no receivers, incoming measurement data requires a separate receiver or transceiver stage. Keep the interface ground referenced to the source ground and apply cable-side surge protection without adding excessive capacitance to the driver outputs.
推荐
Legacy Equipment Retrofit
Retrofits of legacy serial equipment often require a modern controller to drive older RS-232 peripherals while retaining a +5 V power architecture. The ADM234LANZ provides four bipolar transmitter outputs at rates up to 100 kbps, making it suitable for configuration commands and short control exchanges. The through-hole PDIP-16 package is useful where socketed boards and field repairability matter. Before installation, verify the legacy device uses true RS-232 levels rather than TTL, and include external protection for cables connected outside the enclosure.
推荐
Barcode and Identification Equipment
Barcode readers, optical identification stations, and access-control peripherals may use RS-232 command links with rates below 100 kbps. The ADM234LANZ's four driver channels permit a single +5 V controller to address several outbound identification or status paths. Its CMOS implementation and 4.5 V to 5.5 V operating range align with modern embedded supply rails, while the PDIP package simplifies through-hole industrial assembly. Maintain short driver traces, use twisted-pair cabling, and place ESD protection at the external connector.
推荐
Embedded Service and Configuration Port
Embedded machinery often retains an RS-232 configuration port for diagnostics, firmware loading, and factory setup even when the main controller uses modern serial interfaces. The ADM234LANZ generates the required EIA-232-E transmitter levels from one 4.5 V to 5.5 V supply, and its 100 kbps rate is suitable for setup consoles and short diagnostic exchanges. The industrial-grade labeling supports deployment in controlled equipment environments. Confirm the exact temperature limits, provide shutdown control if required by the design, and protect every externally accessible line.
推荐
推荐产品汇总
工程参考数据: ADM234LANZ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ADM234LARZ | ADM234LJNZ | ADM234LAQ | ADM234LAR | MAX234EPE+ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Maxim Integrated |
| Package | PDIP-16, MO-095AC | PDIP-16 | DIP-16 | PDIP-16 | PDIP-16 | PDIP-16 |
| Maximum Data Rate | 100 kbps | 100 kbps-class | 120 kbps | 100 kbps-class | 100 kbps-class | 120 kbps |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
关键差异点
- Single +5 V supply replaces external bipolar rails (对比 ADM232AARW)
- Four dedicated transmitter channels (对比 MAX234EPE+)
- Direct fit in industrial through-hole assemblies (对比 ADM234LJNZ)
设计说明
Do not treat the ADM234LANZ as a complete RS-232 transceiver. It contains four transmitters and no receiver channels, so bidirectional communication requires a separate receiver or transceiver. Also verify the interface requirement is true RS-232 rather than TTL-level UART signaling. According to the Analog Devices datasheet, the drivers target EIA-232-E and V.28 levels; substituting a TTL-only driver would produce an unusable port.
Keep the supply within 4.5 V to 5.5 V and observe the device's specified absolute maximum rating of 5.5 V. The integrated charge-pump circuitry develops bipolar RS-232 transmitter levels from the single +5 V rail, so separate ±12 V supplies are unnecessary. Use local supply decoupling and route the ground return directly to the device; long or shared return paths can degrade transmitter levels and increase susceptibility to cable-induced transients.
Place the ADM234LANZ close to the external connector or protected board edge, and route every RS-232 output as a differential pair with a continuous reference ground. Avoid long unprotected stubs and sharp turns. Add the selected surge and ESD protection network at the connector boundary, and validate that its capacitance and clamp voltage remain compatible with the transmitter slew rate and data rate.
The ADM234LANZ uses a charge-pump design to create bipolar levels from +5 V, so pay attention to supply-current pulsations near the device. Keep the charge-pump supply path compact, provide effective local bypass capacitance, and avoid sharing narrow supply traces with switching regulators. If a system mixes this interface with sensitive analog circuitry, separate the RS-232 return path where possible and use star-point grounding to limit injected noise.
合规信息
The exact ADM234LANZ suffix and manufacturer environmental declarations should be confirmed from the official product documentation before production release. AEC-Q100 is not applicable to this industrial interface IC.