LTC1064CJ - Quad Universal Filter Building Block | Analog Devices
料号: LTC1064CJ ✓ 量产中LTC1064CJ 概述
A switched-capacitor active filter is an analog filter that uses periodically switched capacitors and an external clock to create frequency-dependent behavior equivalent to resistive-capacitive networks. The LTC1064 belongs to the active-filter category, which is part of the broader signal-conditioning IC hierarchy for analog and mixed-signal systems. Its four building blocks can implement multiple second-order filter functions when paired with an external clock and three to five external resistors.
The four independently usable sections provide a practical way to build multichannel signal conditioning without requiring four separate monolithic filter packages. Low noise is valuable when processing weak sensor, audio, communications, or instrumentation signals, while the fast 140 kHz switching capability allows the device to cover a broad range of timing and frequency-response requirements. An external clock gives the system designer control over the switched-capacitor operating rate and filter response.
Each building block uses switched-capacitor techniques to establish its frequency response, but practical performance also depends on the external clock, resistor tolerances, capacitor selection, grounding, and the bandwidth of the signals being filtered. Because the architecture is universal, component values and topology determine whether a section performs low-pass, high-pass, band-pass, band-stop, or another supported second-order function. The four sections can also be combined for higher-order filtering when one section alone does not provide the required attenuation or roll-off.
Typical uses include antialiasing before switched-capacitor data converters, low-noise analog measurement chains, audio signal conditioning, communication-channel filtering, waveform shaping, and general-purpose active filtering. In a multichannel system, identical clocking and closely matched external networks can produce consistent channel behavior, although each section still requires careful component selection and layout.
For reliable implementation, follow the manufacturer datasheet for clock levels, resistor networks, bypass capacitance, grounding, and allowable signal amplitudes. Keep clock routing away from sensitive analog inputs, use a low-noise ground reference, and place filter components close to their associated pins. Validate gain, cutoff frequency, and stopband attenuation with the actual clock and source impedance rather than relying only on nominal calculations.
This page combines the manufacturer product information, package and operating characteristics, practical filter-design guidance, sourcing information, and verified drop-in replacement findings. It is designed to help engineers identify the correct LTC1064CJ ordering code, plan a working filter, and assess replacement options without treating merely similar filter ICs as PCB-compatible substitutes.
直接替换替代料: LTC1064CJ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
LTC1064MJ
✅ 直接替换📋 参考替代料(不在目录中)
LTC1064CJ 最大额定值与电气特性
| Product Type | Quad universal filter building block |
| Number of Filter Sections | 4 sections |
| Filter Architecture | Switched-capacitor active filter |
| Supported Response Functions | Low-pass, high-pass, band-pass, band-stop, and other second-order functions |
| Switched Frequency | 140 kHz |
| Noise Characteristic | Low noise |
| Speed Characteristic | Fast |
| External Clock Requirement | External clock required |
| External Resistors per Section | 3 to 5 resistors |
| Orderable Response Type | Universal |
| 封装 | CDIP-24 |
| Total Pin or Terminal Count | 24 terminals |
| Terminal Form | Through-hole |
| Temperature Grade | Industrial |
| Production Status | Production |
LTC1064CJ cdip-24 引脚配置指南
LTC1064CJ(cdip-24 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: LTC1064CJ.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LTC1064CJ 适用于 6 应用s: Antialiasing Filter for Data Converters, Low-Noise Instrumentation Signal Conditioning, Audio Band-Limiting and Equalization, Communication Channel Filtering, Waveform Shaping and Band-Stop Filtering, Multichannel Sensor Interface.
Antialiasing Filter for Data Converters
The LTC1064CJ suits antialiasing ahead of switched-capacitor data converters because each of its four universal sections can implement a second-order response with an external clock and three to five resistors. Configure low-pass sections according to the converter sampling architecture, then validate attenuation near Nyquist and stopband behavior with the actual clock and source impedance. The 140 kHz switched frequency supports filter timing above many low-rate converter applications, while the low-noise characteristic helps preserve weak analog signals before digitization.
推荐
Low-Noise Instrumentation Signal Conditioning
The LTC1064CJ is appropriate for instrumentation chains where sensor outputs require controlled band-limiting before amplification or measurement. Four low-noise universal sections can process multiple channels or cascade sections to obtain higher-order attenuation. Set cutoff frequency and gain through the external resistor networks, maintain a quiet ground reference, and use matched components when comparing channels. Because the switched-capacitor architecture accepts an external clock, designers can align filter operating conditions with the rest of the measurement system.
推荐
Audio Band-Limiting and Equalization
The LTC1064CJ can implement programmable-by-component low-pass, high-pass, band-pass, or band-stop sections for audio and communications signal conditioning. Its four independent sections allow several filter functions to coexist in one 24-pin CDIP package, reducing the number of separate active-filter packages. The low-noise architecture is useful when weak audio paths require filtering without adding unnecessary broadband noise. Verify audible-band attenuation, distortion, clock feedthrough, and stable passband response in the final analog layout.
推荐
Communication Channel Filtering
The LTC1064CJ is well suited to communication-channel filtering where multiple second-order stages define the occupied bandwidth and reject out-of-band energy. Four sections can each implement a different response or be combined for steeper attenuation. The external clock establishes the switched-capacitor operating condition, while three to five external resistors per section determine the frequency-selective network. Keep the clock away from sensitive inputs and account for source impedance, because both influence practical response and component selection.
推荐
Waveform Shaping and Band-Stop Filtering
The LTC1064CJ can create band-stop or other second-order responses for removing unwanted tones, harmonics, or out-of-band interference from an analog waveform. Each universal section can be configured separately, allowing one package to perform different shaping functions on multiple related signals. Confirm the required clock frequency and external network against the Analog Devices design guidance. Component tolerance and parasitic capacitance should be included in simulation because they can shift the realized cutoff frequency and attenuation.
推荐
Multichannel Sensor Interface
The LTC1064CJ supports multichannel sensor interfaces that require consistent filtering before conversion or control. Four universal building blocks can filter four inputs, or sections can be combined where one channel needs greater roll-off. Use a common clock and closely matched external networks when channel matching matters. The through-hole 24-pin CDIP package also supports conventional plated-through-hole PCB construction, while the low-noise characteristic helps preserve signals from sensitive sensor front ends.
推荐
工程参考数据: LTC1064CJ ——对比、设计指导和合规信息。
选型指南
设计说明
Route the external clock away from filter inputs, resistor-network nodes, and other high-impedance analog traces to minimize coupling into the stopped band. Place each filter network close to the pins it serves, use a common low-impedance ground reference, and keep ground returns short. Confirm the package-specific pin arrangement and recommended grounding topology against the manufacturer datasheet before releasing the PCB layout.
The switched-capacitor response depends on clock quality, source impedance, external resistor accuracy, and stray capacitance. Simulate the complete source and load network, then measure gain, cutoff frequency, stopband attenuation, and clock feedthrough in hardware. When comparing channels, use identical external values and layout symmetry to reduce gain and phase mismatches between the four sections.
Do not treat the four building blocks as four fixed low-pass filters. Each section requires the correct external topology, clock connection, and three to five resistors to implement the intended response. Also avoid selecting another LTC1064 suffix solely by its generic family description, because package and temperature-grade differences can prevent a direct substitution. Validate the exact ordering code and every terminal assignment.
合规信息
The LTC1064 family is listed as a production product, but no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration for the exact LTC1064CJ ordering code appears in the verified product information.