ADM241LARZ - 5V 4/5 RS-232 Transceiver | Analog Devices
料号: ADM241LARZ ✓ 量产中ADM241LARZ 概述
An RS-232 transceiver is an interface IC that combines voltage-line drivers and receivers for bidirectional or multipoint serial communication. RS-232 belongs to the interface-IC hierarchy and uses positive and negative voltage levels to represent digital logic. The ADM241L family is designed for EIA-232-E and V.28 communication interfaces where separate ±12 V supplies are impractical. A single 5 V rail and onboard charge-pump circuitry simplify system power design.
The ADM241LARZ integrates four driver channels and five receiver channels, allowing one package to support several serial links or a mix of transmit and receive functions. Its 120 kB/s maximum data rate suits equipment-control, instrumentation, point-of-sale, industrial, and data-acquisition links that do not require the throughput of a high-speed LVDS interface. Onboard DC-DC converters produce approximately ±9 V output swing, while the small external capacitor requirement of 1 µF reduces board area.
Operationally, the device separates low-voltage logic signaling from the bipolar RS-232 interface. The four drivers translate logic-high and logic-low inputs into RS-232 levels, while the five receivers convert bipolar line voltages back into digital logic outputs. The receiver population is one channel higher than the driver population, allowing a design with four outgoing channels and five incoming channels. The transmitter and receiver enables provide local control over bus participation.
Typical uses include industrial control terminals, laboratory interfaces, POS systems, embedded service ports, and legacy peripheral connections. It is particularly useful when the equipment needs several RS-232 ports but has only a 5 V power rail. Compared with discrete RS-232 drivers and receivers, the integrated device reduces footprint, component count, and the chance of inconsistent charge-pump routing.
For layout, place the 1 µF charge-pump capacitors close to their designated pins and route the high-current loops with minimal area. Keep the logic side away from connector-side return paths, observe the supply and enable sequencing requirements, and test signal integrity with the actual cable and load. The WSOIC package also requires thermal consideration when several drivers operate continuously on bus-limited signals.
This product page consolidates the verified electrical facts, package information, replacement analysis, interface applications, and PCB-design guidance for the ADM241LARZ. It also distinguishes genuine pin-compatible alternatives from related interface ICs that use a different package or channel count.
直接替换替代料: ADM241LARZ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ADM241LARZ (相同外形与封装尺寸) ——差异在于 Maximum Data Rate, Package, Supply Voltage.
ADM241LAR
✅ 直接替换联系询价
查看数据手册 →MAX241CWI+
✅ 直接替换📋 参考替代料(不在目录中)
ADM241LARZ 规格参数
| Product Type | RS-232 transceiver |
| Number of Drivers | 4 |
| Number of Receivers | 5 |
| 电源电压 | 4.5 V to 5.5 V |
| Maximum Data Rate | 120 kB/s |
| RS-232 Output Swing | Approximately ±9 V |
| External Charge-Pump Capacitor | 1 µF |
| Logic Levels | Single 5 V CMOS-compatible interface |
| 封装 | 28-lead WSOIC |
| Driver Enable Control | Yes |
| Receiver Enable Control | Yes |
| Integrated DC-DC Converter | Yes |
| EIA-232-E Compliance | Meets EIA-232-E specifications |
| V.28 Compliance | Meets V.28 specifications |
| RoHS 状态 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
| Lead-Free Status | unknown |
ADM241LARZ 28-lead wsoic 引脚配置指南
ADM241LARZ(28-lead wsoic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ADM241LARZ.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADM241LARZ 适用于 6 应用s: Industrial Control Terminals, Point-of-Sale Equipment, Laboratory Data Acquisition, Embedded Service Ports, Network Equipment Console, Instrumentation and Test Systems.
Industrial Control Terminals
The ADM241LARZ suits industrial terminals that must support several legacy serial links from a single 5 V rail. Four drivers and five receivers provide enough channels for equipment control, status reporting, and local diagnostics without requiring separate driver and receiver packages. Its 120 kB/s maximum data rate is sufficient for command traffic, while onboard DC-DC converters generate approximately ±9 V for the RS-232 side. The 28-lead WSOIC also helps limit board area. Place the required 1 µF charge-pump capacitors close to their pins and keep connector-side current paths compact to preserve signal quality.
推荐
Point-of-Sale Equipment
Point-of-sale products commonly retain RS-232 connections for printers, scanners, scales, and customer displays. The ADM241LARZ consolidates four transmit and five receive channels into one 28-lead WSOIC while accepting a single 4.5 V to 5.5 V supply. The 120 kB/s data rate matches the transaction-oriented traffic commonly used by legacy peripherals. Integrated DC-DC conversion removes the need for a separate negative supply rail, while 1 µF charge-pump capacitors reduce board-space requirements. Validate driver loading, cable length, grounding, and connector protection with the complete peripheral set before production.
推荐
Laboratory Data Acquisition
The ADM241LARZ can connect laboratory instruments and fixture controllers that retain RS-232 command ports. Four drivers support outbound commands to several instruments, while five receivers can collect status or measurement data. A single 5 V rail simplifies adapter-board design, and the 120 kB/s rate is appropriate for short command-and-response transactions rather than continuous high-bandwidth transfer. Onboard DC-DC converters provide approximately ±9 V output swing without an external negative rail. Keep the analog or sensitive measurement circuitry separate from the charge-pump and connector return paths, and confirm grounding to avoid injecting interface transients into measured signals.
推荐
Embedded Service Ports
The ADM241LARZ is useful in embedded systems that must service legacy RS-232 peripherals during installation, configuration, or field diagnostics. Its four driver channels can target several service connectors, and five receiver channels support incoming configuration or acknowledgment signals. Operating from 4.5 V to 5.5 V allows implementation beside common 5 V embedded logic. The 120 kB/s maximum rate is more than adequate for service commands, while onboard DC-DC converters eliminate a separate ±12 V source. Design the enable controls to prevent unnecessary transmitters from driving an inactive bus, and place protection components where they can clamp connector-side transients without adding excessive capacitance to the RS-232 outputs.
推荐
Network Equipment Console
Network and communications equipment often retains an RS-232 console for installation, recovery, and configuration even when primary data transfer uses Ethernet. The ADM241LARZ provides a 5 V-compatible console subsystem with four drivers and five receivers in a 28-lead WSOIC. Its 120 kB/s rate supports terminal interaction and diagnostic commands, while integrated charge pumps supply the required bipolar RS-232 levels. The larger receiver count allows several console or status inputs to share one device. Keep the console channel physically segregated from switching power stages and high-speed interfaces, and verify the adapter-board grounding scheme to prevent console activity from disturbing the main system.
推荐
Instrumentation and Test Systems
The ADM241LARZ can consolidate multiple RS-232 connections in instrumentation and automated test systems where the 5 V supply is available but bipolar line voltage is not. Four drivers can send commands to separate instruments, while five receivers can read independent status channels. The device's 120 kB/s maximum data rate suits supervisory and configuration traffic rather than high-volume sensor streaming. Its onboard DC-DC converters produce approximately ±9 V output swing, and the specified 1 µF capacitor arrangement limits external charge-pump component count. Use short, properly grounded interface wiring and verify that automated test commands cannot leave multiple transmitters active on the same bus.
推荐
推荐产品汇总
工程参考数据: ADM241LARZ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ADM241LAR | MAX241CWI+ |
|---|---|---|---|
| Package | 28-lead WSOIC | 28-lead WSOIC | 28-pin WSOIC |
| Brand | Analog Devices | Analog Devices | Maxim Integrated |
| Transceiver Type | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver |
| Number of Drivers | 4 | 4 | 4 |
| Number of Receivers | 5 | 5 | 5 |
| Supply Voltage | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 5 V |
| Integrated DC-DC Converter | Yes | Yes | Yes |
关键差异点
- Consolidates multiple RS-232 channels in one package (对比 MAX241CWI+)
- Higher documented maximum data rate within the related ADM241L options (对比 ADM241LAR)
- Single-supply implementation with integrated level generation (对比 MAX241CWI+)
设计说明
Place the specified 1 µF charge-pump capacitors directly beside the pins identified in the ADM241L datasheet. Keep the associated switching-current loops compact and avoid routing them beneath the logic ground reference. Because the device generates approximately ±9 V internally, a small loop area helps contain switching noise and improves the likelihood that adjacent low-level logic remains undisturbed.
Do not enable multiple transmitters when they can drive the same RS-232 bus at the same time. The ADM241LARZ has four driver channels, and simultaneous active outputs can create contention even when the logical data appears idle. Review the enable-control truth table and firmware power-up sequence so unused or isolated channels enter a safe state before the system begins transmitting.
Use the pin-description table in the manufacturer datasheet when assigning nets, and treat the connector side as a bipolar RS-232 domain rather than a logic-level domain. Keep return-current paths continuous to the interface ground and separate them from sensitive measurement references. When substituting a compatible 28-pin device, verify enable polarity, charge-pump topology, timing, and output levels rather than relying on package position alone.
合规信息
The interface meets EIA-232-E and V.28 specifications according to the Analog Devices product page. Specific material-compliance declarations are not stated in the available manufacturer product information.