ADM241LARZ - 5V 4/5 RS-232 Transceiver | Analog Devices
MPN: ADM241LARZ ✓ ActiveADM241LARZ Overview
An RS-232 transceiver is an interface IC that combines voltage-line drivers and receivers for bidirectional or multipoint serial communication. RS-232 belongs to the interface-IC hierarchy and uses positive and negative voltage levels to represent digital logic. The ADM241L family is designed for EIA-232-E and V.28 communication interfaces where separate ±12 V supplies are impractical. A single 5 V rail and onboard charge-pump circuitry simplify system power design.
The ADM241LARZ integrates four driver channels and five receiver channels, allowing one package to support several serial links or a mix of transmit and receive functions. Its 120 kB/s maximum data rate suits equipment-control, instrumentation, point-of-sale, industrial, and data-acquisition links that do not require the throughput of a high-speed LVDS interface. Onboard DC-DC converters produce approximately ±9 V output swing, while the small external capacitor requirement of 1 µF reduces board area.
Operationally, the device separates low-voltage logic signaling from the bipolar RS-232 interface. The four drivers translate logic-high and logic-low inputs into RS-232 levels, while the five receivers convert bipolar line voltages back into digital logic outputs. The receiver population is one channel higher than the driver population, allowing a design with four outgoing channels and five incoming channels. The transmitter and receiver enables provide local control over bus participation.
Typical uses include industrial control terminals, laboratory interfaces, POS systems, embedded service ports, and legacy peripheral connections. It is particularly useful when the equipment needs several RS-232 ports but has only a 5 V power rail. Compared with discrete RS-232 drivers and receivers, the integrated device reduces footprint, component count, and the chance of inconsistent charge-pump routing.
For layout, place the 1 µF charge-pump capacitors close to their designated pins and route the high-current loops with minimal area. Keep the logic side away from connector-side return paths, observe the supply and enable sequencing requirements, and test signal integrity with the actual cable and load. The WSOIC package also requires thermal consideration when several drivers operate continuously on bus-limited signals.
This product page consolidates the verified electrical facts, package information, replacement analysis, interface applications, and PCB-design guidance for the ADM241LARZ. It also distinguishes genuine pin-compatible alternatives from related interface ICs that use a different package or channel count.
Drop-in alternatives for ADM241LARZ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with ADM241LARZ (same form factor and footprint) — differing in Maximum Data Rate, Package, Supply Voltage.
ADM241LAR
✅ Drop-InContact for price
View Datasheet →MAX241CWI+
✅ Drop-In📋 Reference alternative (not in catalog)
ADM241LARZ Specifications
| Product Type | RS-232 transceiver |
| Number of Drivers | 4 |
| Number of Receivers | 5 |
| Supply Voltage | 4.5 V to 5.5 V |
| Maximum Data Rate | 120 kB/s |
| RS-232 Output Swing | Approximately ±9 V |
| External Charge-Pump Capacitor | 1 µF |
| Logic Levels | Single 5 V CMOS-compatible interface |
| Package | 28-lead WSOIC |
| Driver Enable Control | Yes |
| Receiver Enable Control | Yes |
| Integrated DC-DC Converter | Yes |
| EIA-232-E Compliance | Meets EIA-232-E specifications |
| V.28 Compliance | Meets V.28 specifications |
| RoHS Status | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
| Lead-Free Status | unknown |
ADM241LARZ 28-lead wsoic Pin Configuration Guide
Pin configuration for ADM241LARZ (28-lead wsoic package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for ADM241LARZ.
Refer to the datasheet for full pin configuration.
Typical Applications
ADM241LARZ is suitable for 6 applications: Industrial Control Terminals, Point-of-Sale Equipment, Laboratory Data Acquisition, Embedded Service Ports, Network Equipment Console, Instrumentation and Test Systems.
Industrial Control Terminals
The ADM241LARZ suits industrial terminals that must support several legacy serial links from a single 5 V rail. Four drivers and five receivers provide enough channels for equipment control, status reporting, and local diagnostics without requiring separate driver and receiver packages. Its 120 kB/s maximum data rate is sufficient for command traffic, while onboard DC-DC converters generate approximately ±9 V for the RS-232 side. The 28-lead WSOIC also helps limit board area. Place the required 1 µF charge-pump capacitors close to their pins and keep connector-side current paths compact to preserve signal quality.
Recommended
Point-of-Sale Equipment
Point-of-sale products commonly retain RS-232 connections for printers, scanners, scales, and customer displays. The ADM241LARZ consolidates four transmit and five receive channels into one 28-lead WSOIC while accepting a single 4.5 V to 5.5 V supply. The 120 kB/s data rate matches the transaction-oriented traffic commonly used by legacy peripherals. Integrated DC-DC conversion removes the need for a separate negative supply rail, while 1 µF charge-pump capacitors reduce board-space requirements. Validate driver loading, cable length, grounding, and connector protection with the complete peripheral set before production.
Recommended
Laboratory Data Acquisition
The ADM241LARZ can connect laboratory instruments and fixture controllers that retain RS-232 command ports. Four drivers support outbound commands to several instruments, while five receivers can collect status or measurement data. A single 5 V rail simplifies adapter-board design, and the 120 kB/s rate is appropriate for short command-and-response transactions rather than continuous high-bandwidth transfer. Onboard DC-DC converters provide approximately ±9 V output swing without an external negative rail. Keep the analog or sensitive measurement circuitry separate from the charge-pump and connector return paths, and confirm grounding to avoid injecting interface transients into measured signals.
Recommended
Embedded Service Ports
The ADM241LARZ is useful in embedded systems that must service legacy RS-232 peripherals during installation, configuration, or field diagnostics. Its four driver channels can target several service connectors, and five receiver channels support incoming configuration or acknowledgment signals. Operating from 4.5 V to 5.5 V allows implementation beside common 5 V embedded logic. The 120 kB/s maximum rate is more than adequate for service commands, while onboard DC-DC converters eliminate a separate ±12 V source. Design the enable controls to prevent unnecessary transmitters from driving an inactive bus, and place protection components where they can clamp connector-side transients without adding excessive capacitance to the RS-232 outputs.
Recommended
Network Equipment Console
Network and communications equipment often retains an RS-232 console for installation, recovery, and configuration even when primary data transfer uses Ethernet. The ADM241LARZ provides a 5 V-compatible console subsystem with four drivers and five receivers in a 28-lead WSOIC. Its 120 kB/s rate supports terminal interaction and diagnostic commands, while integrated charge pumps supply the required bipolar RS-232 levels. The larger receiver count allows several console or status inputs to share one device. Keep the console channel physically segregated from switching power stages and high-speed interfaces, and verify the adapter-board grounding scheme to prevent console activity from disturbing the main system.
Recommended
Instrumentation and Test Systems
The ADM241LARZ can consolidate multiple RS-232 connections in instrumentation and automated test systems where the 5 V supply is available but bipolar line voltage is not. Four drivers can send commands to separate instruments, while five receivers can read independent status channels. The device's 120 kB/s maximum data rate suits supervisory and configuration traffic rather than high-volume sensor streaming. Its onboard DC-DC converters produce approximately ±9 V output swing, and the specified 1 µF capacitor arrangement limits external charge-pump component count. Use short, properly grounded interface wiring and verify that automated test commands cannot leave multiple transmitters active on the same bus.
Recommended
Recommended Products Summary
Engineering reference data for ADM241LARZ — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | ADM241LAR | MAX241CWI+ |
|---|---|---|---|
| Package | 28-lead WSOIC | 28-lead WSOIC | 28-pin WSOIC |
| Brand | Analog Devices | Analog Devices | Maxim Integrated |
| Transceiver Type | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver |
| Number of Drivers | 4 | 4 | 4 |
| Number of Receivers | 5 | 5 | 5 |
| Supply Voltage | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 5 V |
| Integrated DC-DC Converter | Yes | Yes | Yes |
Key Differentiators
- Consolidates multiple RS-232 channels in one package (vs MAX241CWI+)
- Higher documented maximum data rate within the related ADM241L options (vs ADM241LAR)
- Single-supply implementation with integrated level generation (vs MAX241CWI+)
Design Notes
Place the specified 1 µF charge-pump capacitors directly beside the pins identified in the ADM241L datasheet. Keep the associated switching-current loops compact and avoid routing them beneath the logic ground reference. Because the device generates approximately ±9 V internally, a small loop area helps contain switching noise and improves the likelihood that adjacent low-level logic remains undisturbed.
Do not enable multiple transmitters when they can drive the same RS-232 bus at the same time. The ADM241LARZ has four driver channels, and simultaneous active outputs can create contention even when the logical data appears idle. Review the enable-control truth table and firmware power-up sequence so unused or isolated channels enter a safe state before the system begins transmitting.
Use the pin-description table in the manufacturer datasheet when assigning nets, and treat the connector side as a bipolar RS-232 domain rather than a logic-level domain. Keep return-current paths continuous to the interface ground and separate them from sensitive measurement references. When substituting a compatible 28-pin device, verify enable polarity, charge-pump topology, timing, and output levels rather than relying on package position alone.
Compliance Information
The interface meets EIA-232-E and V.28 specifications according to the Analog Devices product page. Specific material-compliance declarations are not stated in the available manufacturer product information.