ADM4850ARZ - 5V RS-485 Transceiver | Analog Devices
料号: ADM4850ARZ ✓ 量产中ADM4850ARZ 概述
An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into balanced differential signals for reliable communication over cables and multidrop buses. The differential signal architecture belongs to the broader interface IC hierarchy and supports noise-resistant industrial communication. The ADM4850 family also includes related half-duplex and full-duplex differential line transceivers designed for high-speed multipoint data links.
The ADM4850ARZ operates from a 5 V supply and is identified as a single-channel, half-duplex RS-422/RS-485 transceiver. Slew-rate limitation is the central feature for practical bus deployments because it reduces edge energy that can propagate as electromagnetic interference. The 115 kbps operating rate supports conventional industrial-control traffic where robust signaling and reduced EMI are more important than very high data throughput.
The device combines a differential line driver with a differential receiver so that a node can transmit and receive on the same bus pair. Communication direction is normally managed by an external control signal or host interface. In a multidrop network, multiple nodes can share the bus when only one transmitter is active at a time; bus contention remains a system-level concern that must be prevented by the controller and driver-enable logic.
Typical uses include industrial sensor networks, building automation equipment, factory data buses, process-control links, and embedded serial interfaces. The part is also appropriate for laboratory or instrumentation systems that require balanced differential signaling over cables longer or noisier than an ordinary point-to-point logic connection. Applications requiring full-duplex operation should instead select a suitable full-duplex member of the ADM485 family.
PCB implementation should preserve the differential route between the transceiver and the connector, minimize stub lengths, and provide a controlled return path for the common-mode reference. External termination, biasing, and protection components must be selected from the cable length, topology, and baud rate rather than copied blindly between unrelated designs.
This product page combines the manufacturer device information, distributor identification, package details, interface standards, and drop-in replacement information. It also adds application-focused engineering guidance and a parameter comparison intended to make PCB reuse and transceiver selection more explicit than a basic catalog listing.
直接替换替代料: ADM4850ARZ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ADM4850ARZ (相同外形与封装尺寸) ——差异在于 Package, Product Type, Maximum Data Rate, Slew Rate, Duplex Mode.
ADM4851AR
✅ 直接替换联系询价
查看数据手册 →ADM4855AR
✅ 直接替换联系询价
查看数据手册 →ADM4850ARZ 规格参数
| Product Type | Differential line transceiver |
| Supported Standards | EIA RS-485 and RS-422 |
| 电源电压 | 5 V |
| Maximum Data Rate | 115 kbps |
| Duplex Mode | Half-duplex |
| Signal Type | Balanced differential |
| Bus Architecture | Multipoint bus |
| Slew Rate | Limited |
| Transmitter Count | 1 |
| Receiver Count | 1 |
| 封装 | 8-pin SOIC |
| 安装类型 | Surface mount |
| Tube Quantity | 1 unit per tube |
| Reel Packaging | ADM4850ARZ-REEL7 |
| Datasheet Revision | Rev. F |
ADM4850ARZ 8-pin soic 引脚配置指南
ADM4850ARZ(8-pin soic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ADM4850ARZ.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADM4850ARZ 适用于 6 应用s: Industrial Sensor Bus, Building Automation Network, Process-Control Equipment, Factory Data Acquisition, Instrumentation and Test Equipment, Telecom Power and Monitoring.
Industrial Sensor Bus
The ADM4850ARZ fits industrial sensor and actuator networks that use balanced RS-485 signaling over extended cables. Its 115 kbps maximum rate is appropriate for moderate-rate telemetry, while slew-rate limitation reduces the high-frequency edge energy that can interfere with nearby equipment. The 5 V half-duplex transceiver supports a shared differential pair when only one node transmits at a time. Designers should implement direction control in the host controller, minimize cable stubs, and apply termination and protection according to the bus topology.
推荐
Building Automation Network
The ADM4850ARZ is suitable for building-automation controllers, room modules, and HVAC interface boards that distribute control commands over an RS-485 network. Its 115 kbps rate supports ordinary supervisory-control traffic without requiring a high-speed serial interface, and the slew-rate-limited driver helps reduce cable EMI in environments containing numerous control cables. Use a single active transmitter at a time and terminate only the physical ends of the bus. Surge protection and proper common-mode grounding are important when control lines pass between buildings or electrically separated equipment.
推荐
Process-Control Equipment
The ADM4850ARZ can connect sensors, remote I/O, and control equipment to a process-control master through an RS-485 or RS-422 link. The half-duplex 115 kbps operation provides a practical balance between update rate, cable reach, and reduced electromagnetic emissions. Because the bus can represent a multipoint network, software and hardware should prevent simultaneous transmission, provide failsafe biasing where required, and use controlled termination. The differential interface also helps reject common-mode noise encountered near motors, contactors, and switching power equipment.
推荐
Factory Data Acquisition
The ADM4850ARZ is appropriate for factory data-acquisition nodes that collect measurements from distributed instruments over a wired bus. Its 5 V operation fits embedded controller boards, while the 115 kbps rate accommodates routine status and measurement traffic. The balanced line reduces susceptibility to differential noise compared with a single-ended interface, and slew-rate control limits harmful fast-edge energy. Layout should keep the differential pair continuous from the transceiver to the connector, avoid unnecessary test pads that create stubs, and separate the bus routing from switching-power paths.
推荐
Instrumentation and Test Equipment
The ADM4850ARZ can connect laboratory instruments, automated test fixtures, and service equipment over a balanced RS-485 or RS-422 link. The 115 kbps half-duplex rate is suitable for command and response traffic, while slew-rate limitation makes the interface practical where long test leads could otherwise radiate significant EMI. Keep the differential trace geometry consistent and provide a stable reference near the connector. External protection may be needed when leads connect to externally accessible equipment, and direction control should be deterministic to avoid bus contention during repeated automated test cycles.
推荐
Telecom Power and Monitoring
The ADM4850ARZ can be used in remote monitoring units, battery-powered field equipment, and telecom support modules that need a robust wired supervisory channel. The 5 V half-duplex interface operates at up to 115 kbps, allowing status and configuration data to share a multidrop RS-485 bus. Its differential signaling is well suited to installations with electrically noisy power systems, while controlled transition rates limit cable emissions. The completed design still needs careful grounding, surge protection, and bus-termination calculations based on cable length, propagation delay, and the number of connected nodes.
推荐
推荐产品汇总
工程参考数据: ADM4850ARZ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ADM4851AR | ADM4855AR | ADM489AR |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Product Family | ADM485 | ADM485 | ADM485 | ADM489 |
关键差异点
- Established 115 kbps half-duplex operating point (对比 ADM489AR)
- Slew-rate-limited differential output (对比 ADM4851AR)
- Single 5 V operating architecture (对比 ADM4855AR)
设计说明
Route the differential bus as a continuous pair from the ADM4850ARZ to the connector, with consistent spacing and a continuous reference plane. Avoid branch stubs because their reflections can degrade the 115 kbps signal. Place any protection components close to the connector and keep their return path to the transceiver ground low-inductance.
Do not enable more than one transmitter on a shared RS-485 bus at the same time. Bus contention can produce excessive current and unreliable communication. Use a defined direction-control signal, disable the driver promptly after transmission, and confirm failsafe behavior for the receiver when the bus is idle or disconnected.
Retain the ADM4850's slew-rate-limited drive characteristics because the 115 kbps operating rate is specifically suited to reducing fast-edge emissions on multipoint cables. Do not substitute a much faster edge-rate driver without re-evaluating EMI, reflections, and termination. Keep switching converters and high-current return paths away from the differential route and connector ground path.
Calculate termination and biasing for the completed network rather than applying them by default. Place termination at the physical ends of the bus, avoid duplicating termination at every node, and provide failsafe bias only once where appropriate. Account for connector stubs, cable type, node count, and propagation delay at the selected 115 kbps operating rate.
合规信息
The verified device information identifies EIA RS-485 and RS-422 compliance but does not provide explicit RoHS, REACH, halogen-free, or conflict-minerals declarations. AEC-Q100 is not applicable to this general-purpose interface IC.