ATF16V8CZ-12SC - 12ns 8-Macrocell EEPLD | Microchip
料号: ATF16V8CZ-12SC ✓ 量产中ATF16V8CZ-12SC 概述
An electrically erasable programmable logic device, or EEPLD, belongs to the programmable-logic hierarchy alongside PAL and GAL devices. Unlike a mask-programmed PLD, its fuse configuration can be changed by programming equipment. The ATF16V8CZ architecture supports registered, combinatorial, and complex-mode logic configurations selected through the device programming files, making it useful for consolidating multiple gates and flip-flops into one configurable logic component.
The ATF16V8CZ family provides 250 usable gates, eight outputs, and up to 16 input terms. Each output is allocated eight product terms. A maximum pin-to-pin propagation delay of 12 ns characterizes the -12 speed grade, allowing the device to address general-purpose industrial control, interface decoding, data routing, and compact control logic where moderate timing performance is sufficient.
The ATF16V8CZ incorporates a superset of common 16R8 and 20-pin combinatorial PLD architectures, helping simplify replacements when migrating older PAL-compatible designs. Its outputs support TTL-compatible interfacing, and its electrically erasable configuration allows design revisions without changing the PCB. A zero-power specification and low 25 µA standby current are useful where inactive-state power is important.
Typical uses include industrial control logic, consumer-equipment decoding, automotive interface functions, keyboard or display control, and compact combinational or registered logic networks. The 20-SOIC package provides a conventional surface-mount footprint for assembly and rework, although modern high-density designs may favor smaller programmable-logic devices when I/O count permits.
For reliable implementation, confirm the fuse map and pin assignments against the manufacturer datasheet before manufacturing. Configure the device with compatible programming software, validate every unused input state, and check timing against the full external path rather than only the stated pin-to-pin delay. The -12 speed grade should be selected when its 12 ns maximum propagation delay provides adequate timing margin.
This page combines device specifications, practical implementation guidance, application fit, and drop-in replacement analysis to support faster engineering evaluation. It also distinguishes electrically erasable logic from mask-programmed devices and helps designers assess whether the 16-input, 8-output architecture matches the required control system.
直接替换替代料: ATF16V8CZ-12SC ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ATF16V8CZ-12SC (相同外形与封装尺寸) ——差异在于 Architecture, Package.
ATF16V8CZ-12JC
✅ 直接替换联系询价
查看数据手册 →ATF16V8CZ-10JC
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
ATF16V8CZ-15JC
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →ATF16V8CZ-20JC
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
ATF16V8CZ-10SC
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
ATF16V8CZ-12SC 最大额定值与电气特性
| Device Type | Electrically erasable programmable logic device (EEPLD) |
| Architecture | 16V8 with 250 usable gates |
| 电源电压 | 5 V |
| Input Count | Up to 16 inputs |
| Output Count | 8 outputs |
| Macrocells | 8 macrocells |
| Maximum Pin-to-Pin Delay | 12 ns |
| Standby Current | 25 µA |
| Product Terms per Output | 8 product terms |
| Input Logic Compatibility | CMOS and TTL compatible |
| Output Logic Compatibility | CMOS and TTL compatible |
| Configuration Technology | Electrically erasable |
| Operating Modes | Registered, combinatorial, and complex modes |
| 封装 | 20-SOIC, 7.50 mm width |
| 安装类型 | Surface mount |
| Package Classification | Green package |
ATF16V8CZ-12SC green package 引脚配置指南
ATF16V8CZ-12SC(green package 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: ATF16V8CZ-12SC.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ATF16V8CZ-12SC 适用于 6 应用s: Industrial Control Logic, Automotive Interface Logic, Interface Signal Decoding, Consumer Equipment Control, Data Routing and Multiplexing, Legacy PAL-Compatible Consolidation.
Industrial Control Logic
The ATF16V8CZ-12SC fits compact industrial control logic where up to 16 inputs and 8 outputs can implement interlocks, sequencing, command decoding, and discrete state transitions. Its 12 ns maximum pin-to-pin delay supports moderate-speed combinational paths, while registered and complex modes accommodate clocked control functions. The 5 V supply and CMOS/TTL-compatible interfacing simplify connection to older logic families, although industrial temperature and transient requirements must be confirmed for the exact suffix. Verify timing margin against the master clock and ensure unused inputs are tied to defined levels before programming.
推荐
Automotive Interface Logic
The ATF16V8CZ-12SC can consolidate automotive accessory, switch, and signal-routing logic when the electrical environment and qualification requirements permit the selected device grade. Eight configurable outputs and up to 16 inputs are useful for decoding switches, generating control strobes, and implementing small state machines. The -12 speed grade provides a 12 ns maximum pin-to-pin delay, but automotive use requires review of temperature range, AEC-Q100 qualification, ESD protection, transient immunity, and supplier quality requirements rather than logic functionality alone.
推荐
Interface Signal Decoding
The ATF16V8CZ-12SC is useful for decoding address, command, or control signals into internal enables and data-route controls. Sixteen input terms provide enough capacity for practical Boolean decoding, while eight product terms per output support more complex equations than basic gate equivalents. The device can replace multiple PAL-compatible logic sections and supports registered operation when downstream circuits require synchronized controls. Designers should simulate the complete input truth table and verify that every output's polarity, feedback path, and registered-state behavior match the intended architecture.
推荐
Consumer Equipment Control
The ATF16V8CZ-12SC can implement compact control logic for consumer products requiring mode selection, button decoding, display sequencing, or interlock functions. Its electrically erasable architecture allows the firmware-equivalent configuration to be revised during product development without replacing the device, and the 20-SOIC package supports conventional PCB assembly. The 25 µA standby specification helps when inactive-state consumption matters. For battery-operated products, calculate the complete system budget because standby current does not represent active dynamic current or leakage from external logic paths.
推荐
Data Routing and Multiplexing
The ATF16V8CZ-12SC can route control and status signals or implement small multiplexers where eight outputs select or qualify multiple 5 V logic signals. Its 16-input architecture permits several candidate inputs and control terms to feed each output equation, while the 12 ns speed grade addresses moderate propagation requirements. For clocked multiplexing, use the registered mode and include setup-time, clock-to-output, and interconnect delay in the timing analysis. Confirm the programmed fuse map and test all feedback and cascading paths, since these can affect both functional behavior and timing.
推荐
Legacy PAL-Compatible Consolidation
The ATF16V8CZ-12SC is appropriate for consolidating legacy 16R8 and many 20-pin combinatorial PLD functions into a single electrically erasable device. Its architecture forms a superset of common generic PLD arrangements, while the eight-macrocell structure supports combinational, registered, and complex configurations. This can simplify board assembly and permit design revisions through reprogramming. Migration still requires a detailed pin-by-pin comparison, logic-equation conversion, polarity review, and timing validation rather than assuming that every legacy fuse pattern transfers without review.
推荐
推荐产品汇总
工程参考数据: ATF16V8CZ-12SC ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ATF16V8CZ-12JC | ATF16V8CZ-10JC | ATF16V8CZ-15JC | ATF16V8CZ-20JC | ATF16V8CZ-10SC |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 20-SOIC | 20-SOIC - same | 20-SOIC - same | 20-SOIC - same | 20-SOIC - same | 20-SOIC - same |
| Device Architecture | ATF16V8CZ, 8 macrocells | ATF16V8CZ, 8 macrocells | ATF16V8CZ, 8 macrocells | ATF16V8CZ, 8 macrocells | ATF16V8CZ, 8 macrocells | ATF16V8CZ, 8 macrocells |
| Maximum Pin-to-Pin Delay | 12 ns | 12 ns | 10 ns | 15 ns | 20 ns | 10 ns |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Logic Compatibility | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible |
| Macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells |
| Input and Output Count | Up to 16 inputs and 8 outputs | Up to 16 inputs and 8 outputs | Up to 16 inputs and 8 outputs | Up to 16 inputs and 8 outputs | Up to 16 inputs and 8 outputs | Up to 16 inputs and 8 outputs |
| Standby Current | 25 µA | 25 µA | 25 µA | 25 µA | 25 µA | 25 µA |
| Temperature Classification | Commercial SC classification | Industrial J classification | Industrial J classification | Industrial J classification | Industrial J classification | Commercial SC classification |
关键差异点
- Matches the 12 ns timing grade in an alternate temperature classification (对比 ATF16V8CZ-12JC)
- Provides 2 ns lower propagation delay for tighter timing budgets (对比 ATF16V8CZ-10JC)
- Retains the commercial temperature class with faster timing (对比 ATF16V8CZ-10SC)
设计说明
Do not treat the 12 ns pin-to-pin figure as complete system timing. For a registered path, add input setup time, clock-to-output delay, board propagation, and receiver setup time; for a combinational path, include every cascaded output and feedback segment. Select the -10 grade if the calculated margin is insufficient, and confirm that the replacement retains the 20-SOIC footprint and programmed fuse map.
Budget active and standby current separately. The 25 µA standby figure applies to the stated low-power condition, not necessarily maximum dynamic current. At 5 V, 25 µA corresponds to 0.125 mW of standby power in the specified state. External pull resistors, input leakage, and attached logic can dominate the complete board's inactive consumption, so include them in the system power budget.
Place the 20-SOIC on a footprint matching the manufacturer's package drawing, including lead pitch, body width, and solder-land geometry. Keep clock and high-fanout output traces short, provide a direct ground-return path, and isolate noisy switching nodes from logic inputs. Check every unused pin's required state in the configuration file before releasing the PCB for fabrication.
Validate the electrical-erasable configuration after programming and include the device identifier, fuse checksum, and supply condition in the manufacturing record. A successful programming operation does not prove that output polarity, registered feedback, or product-term allocation matches the intended schematic. Run boundary-pattern tests on assembled boards to detect an incorrect fuse map or package orientation.
合规信息
The manufacturer product page identifies a green package but does not provide extractable RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations.