ATF16V8CZ-12SC - 12ns 8-Macrocell EEPLD | Microchip
MPN: ATF16V8CZ-12SC ✓ 啟用中ATF16V8CZ-12SC 概覽
An electrically erasable programmable logic device, or EEPLD, belongs to the programmable-logic hierarchy alongside PAL and GAL devices. Unlike a mask-programmed PLD, its fuse configuration can be changed by programming equipment. The ATF16V8CZ architecture supports registered, combinatorial, and complex-mode logic configurations selected through the device programming files, making it useful for consolidating multiple gates and flip-flops into one configurable logic component.
The ATF16V8CZ family provides 250 usable gates, eight outputs, and up to 16 input terms. Each output is allocated eight product terms. A maximum pin-to-pin propagation delay of 12 ns characterizes the -12 speed grade, allowing the device to address general-purpose industrial control, interface decoding, data routing, and compact control logic where moderate timing performance is sufficient.
The ATF16V8CZ incorporates a superset of common 16R8 and 20-pin combinatorial PLD architectures, helping simplify replacements when migrating older PAL-compatible designs. Its outputs support TTL-compatible interfacing, and its electrically erasable configuration allows design revisions without changing the PCB. A zero-power specification and low 25 µA standby current are useful where inactive-state power is important.
Typical uses include industrial control logic, consumer-equipment decoding, automotive interface functions, keyboard or display control, and compact combinational or registered logic networks. The 20-SOIC package provides a conventional surface-mount footprint for assembly and rework, although modern high-density designs may favor smaller programmable-logic devices when I/O count permits.
For reliable implementation, confirm the fuse map and pin assignments against the manufacturer datasheet before manufacturing. Configure the device with compatible programming software, validate every unused input state, and check timing against the full external path rather than only the stated pin-to-pin delay. The -12 speed grade should be selected when its 12 ns maximum propagation delay provides adequate timing margin.
This page combines device specifications, practical implementation guidance, application fit, and drop-in replacement analysis to support faster engineering evaluation. It also distinguishes electrically erasable logic from mask-programmed devices and helps designers assess whether the 16-input, 8-output architecture matches the required control system.
直接替換替代品,適用於 ATF16V8CZ-12SC — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ATF16V8CZ-12SC (相同外形與佔位) — 差異在於 Architecture, Package.
ATF16V8CZ-12JC
✅ 直接替換聯絡詢價
查看資料表 →ATF16V8CZ-10JC
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ATF16V8CZ-15JC
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →ATF16V8CZ-20JC
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ATF16V8CZ-10SC
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ATF16V8CZ-12SC 最大額定值與電氣特性
| Device Type | Electrically erasable programmable logic device (EEPLD) |
| Architecture | 16V8 with 250 usable gates |
| 供應電壓 | 5 V |
| Input Count | Up to 16 inputs |
| Output Count | 8 outputs |
| Macrocells | 8 macrocells |
| Maximum Pin-to-Pin Delay | 12 ns |
| Standby Current | 25 µA |
| Product Terms per Output | 8 product terms |
| Input Logic Compatibility | CMOS and TTL compatible |
| Output Logic Compatibility | CMOS and TTL compatible |
| Configuration Technology | Electrically erasable |
| Operating Modes | Registered, combinatorial, and complex modes |
| 封裝 | 20-SOIC, 7.50 mm width |
| 安裝類型 | Surface mount |
| Package Classification | Green package |
ATF16V8CZ-12SC green package 腳位配置指南
ATF16V8CZ-12SC(green package 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: ATF16V8CZ-12SC.
請參閱 資料表 以查看完整腳位配置。
典型應用
ATF16V8CZ-12SC 適用於 6 應用s: Industrial Control Logic, Automotive Interface Logic, Interface Signal Decoding, Consumer Equipment Control, Data Routing and Multiplexing, Legacy PAL-Compatible Consolidation.
Industrial Control Logic
The ATF16V8CZ-12SC fits compact industrial control logic where up to 16 inputs and 8 outputs can implement interlocks, sequencing, command decoding, and discrete state transitions. Its 12 ns maximum pin-to-pin delay supports moderate-speed combinational paths, while registered and complex modes accommodate clocked control functions. The 5 V supply and CMOS/TTL-compatible interfacing simplify connection to older logic families, although industrial temperature and transient requirements must be confirmed for the exact suffix. Verify timing margin against the master clock and ensure unused inputs are tied to defined levels before programming.
推薦
Automotive Interface Logic
The ATF16V8CZ-12SC can consolidate automotive accessory, switch, and signal-routing logic when the electrical environment and qualification requirements permit the selected device grade. Eight configurable outputs and up to 16 inputs are useful for decoding switches, generating control strobes, and implementing small state machines. The -12 speed grade provides a 12 ns maximum pin-to-pin delay, but automotive use requires review of temperature range, AEC-Q100 qualification, ESD protection, transient immunity, and supplier quality requirements rather than logic functionality alone.
推薦
Interface Signal Decoding
The ATF16V8CZ-12SC is useful for decoding address, command, or control signals into internal enables and data-route controls. Sixteen input terms provide enough capacity for practical Boolean decoding, while eight product terms per output support more complex equations than basic gate equivalents. The device can replace multiple PAL-compatible logic sections and supports registered operation when downstream circuits require synchronized controls. Designers should simulate the complete input truth table and verify that every output's polarity, feedback path, and registered-state behavior match the intended architecture.
推薦
Consumer Equipment Control
The ATF16V8CZ-12SC can implement compact control logic for consumer products requiring mode selection, button decoding, display sequencing, or interlock functions. Its electrically erasable architecture allows the firmware-equivalent configuration to be revised during product development without replacing the device, and the 20-SOIC package supports conventional PCB assembly. The 25 µA standby specification helps when inactive-state consumption matters. For battery-operated products, calculate the complete system budget because standby current does not represent active dynamic current or leakage from external logic paths.
推薦
Data Routing and Multiplexing
The ATF16V8CZ-12SC can route control and status signals or implement small multiplexers where eight outputs select or qualify multiple 5 V logic signals. Its 16-input architecture permits several candidate inputs and control terms to feed each output equation, while the 12 ns speed grade addresses moderate propagation requirements. For clocked multiplexing, use the registered mode and include setup-time, clock-to-output, and interconnect delay in the timing analysis. Confirm the programmed fuse map and test all feedback and cascading paths, since these can affect both functional behavior and timing.
推薦
Legacy PAL-Compatible Consolidation
The ATF16V8CZ-12SC is appropriate for consolidating legacy 16R8 and many 20-pin combinatorial PLD functions into a single electrically erasable device. Its architecture forms a superset of common generic PLD arrangements, while the eight-macrocell structure supports combinational, registered, and complex configurations. This can simplify board assembly and permit design revisions through reprogramming. Migration still requires a detailed pin-by-pin comparison, logic-equation conversion, polarity review, and timing validation rather than assuming that every legacy fuse pattern transfers without review.
推薦
推薦產品摘要
工程參考資料,適用於 ATF16V8CZ-12SC — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ATF16V8CZ-12JC | ATF16V8CZ-10JC | ATF16V8CZ-15JC | ATF16V8CZ-20JC | ATF16V8CZ-10SC |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 20-SOIC | 20-SOIC - same | 20-SOIC - same | 20-SOIC - same | 20-SOIC - same | 20-SOIC - same |
| Device Architecture | ATF16V8CZ, 8 macrocells | ATF16V8CZ, 8 macrocells | ATF16V8CZ, 8 macrocells | ATF16V8CZ, 8 macrocells | ATF16V8CZ, 8 macrocells | ATF16V8CZ, 8 macrocells |
| Maximum Pin-to-Pin Delay | 12 ns | 12 ns | 10 ns | 15 ns | 20 ns | 10 ns |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Logic Compatibility | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible |
| Macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells |
| Input and Output Count | Up to 16 inputs and 8 outputs | Up to 16 inputs and 8 outputs | Up to 16 inputs and 8 outputs | Up to 16 inputs and 8 outputs | Up to 16 inputs and 8 outputs | Up to 16 inputs and 8 outputs |
| Standby Current | 25 µA | 25 µA | 25 µA | 25 µA | 25 µA | 25 µA |
| Temperature Classification | Commercial SC classification | Industrial J classification | Industrial J classification | Industrial J classification | Industrial J classification | Commercial SC classification |
主要差異化特點
- Matches the 12 ns timing grade in an alternate temperature classification (對比ATF16V8CZ-12JC)
- Provides 2 ns lower propagation delay for tighter timing budgets (對比ATF16V8CZ-10JC)
- Retains the commercial temperature class with faster timing (對比ATF16V8CZ-10SC)
設計說明
Do not treat the 12 ns pin-to-pin figure as complete system timing. For a registered path, add input setup time, clock-to-output delay, board propagation, and receiver setup time; for a combinational path, include every cascaded output and feedback segment. Select the -10 grade if the calculated margin is insufficient, and confirm that the replacement retains the 20-SOIC footprint and programmed fuse map.
Budget active and standby current separately. The 25 µA standby figure applies to the stated low-power condition, not necessarily maximum dynamic current. At 5 V, 25 µA corresponds to 0.125 mW of standby power in the specified state. External pull resistors, input leakage, and attached logic can dominate the complete board's inactive consumption, so include them in the system power budget.
Place the 20-SOIC on a footprint matching the manufacturer's package drawing, including lead pitch, body width, and solder-land geometry. Keep clock and high-fanout output traces short, provide a direct ground-return path, and isolate noisy switching nodes from logic inputs. Check every unused pin's required state in the configuration file before releasing the PCB for fabrication.
Validate the electrical-erasable configuration after programming and include the device identifier, fuse checksum, and supply condition in the manufacturing record. A successful programming operation does not prove that output polarity, registered feedback, or product-term allocation matches the intended schematic. Run boundary-pattern tests on assembled boards to detect an incorrect fuse map or package orientation.
合規資訊
The manufacturer product page identifies a green package but does not provide extractable RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations.