ATF16V8CZ-12SC - 12ns 8-Macrocell EEPLD | Microchip
부품 번호: ATF16V8CZ-12SC ✓ 활성ATF16V8CZ-12SC 개요
An electrically erasable programmable logic device, or EEPLD, belongs to the programmable-logic hierarchy alongside PAL and GAL devices. Unlike a mask-programmed PLD, its fuse configuration can be changed by programming equipment. The ATF16V8CZ architecture supports registered, combinatorial, and complex-mode logic configurations selected through the device programming files, making it useful for consolidating multiple gates and flip-flops into one configurable logic component.
The ATF16V8CZ family provides 250 usable gates, eight outputs, and up to 16 input terms. Each output is allocated eight product terms. A maximum pin-to-pin propagation delay of 12 ns characterizes the -12 speed grade, allowing the device to address general-purpose industrial control, interface decoding, data routing, and compact control logic where moderate timing performance is sufficient.
The ATF16V8CZ incorporates a superset of common 16R8 and 20-pin combinatorial PLD architectures, helping simplify replacements when migrating older PAL-compatible designs. Its outputs support TTL-compatible interfacing, and its electrically erasable configuration allows design revisions without changing the PCB. A zero-power specification and low 25 µA standby current are useful where inactive-state power is important.
Typical uses include industrial control logic, consumer-equipment decoding, automotive interface functions, keyboard or display control, and compact combinational or registered logic networks. The 20-SOIC package provides a conventional surface-mount footprint for assembly and rework, although modern high-density designs may favor smaller programmable-logic devices when I/O count permits.
For reliable implementation, confirm the fuse map and pin assignments against the manufacturer datasheet before manufacturing. Configure the device with compatible programming software, validate every unused input state, and check timing against the full external path rather than only the stated pin-to-pin delay. The -12 speed grade should be selected when its 12 ns maximum propagation delay provides adequate timing margin.
This page combines device specifications, practical implementation guidance, application fit, and drop-in replacement analysis to support faster engineering evaluation. It also distinguishes electrically erasable logic from mask-programmed devices and helps designers assess whether the 16-input, 8-output architecture matches the required control system.
드롭인 대체품: ATF16V8CZ-12SC — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATF16V8CZ-12SC (동일 폼 팩터 및 풋프린트) — 차이점: Architecture, Package.
ATF16V8CZ-12JC
✅ 드롭인가격 문의
데이터시트 보기 →ATF16V8CZ-10JC
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ATF16V8CZ-15JC
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →ATF16V8CZ-20JC
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ATF16V8CZ-10SC
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ATF16V8CZ-12SC 최대 정격 & 전기적 특성
| Device Type | Electrically erasable programmable logic device (EEPLD) |
| Architecture | 16V8 with 250 usable gates |
| 공급 전압 | 5 V |
| Input Count | Up to 16 inputs |
| Output Count | 8 outputs |
| Macrocells | 8 macrocells |
| Maximum Pin-to-Pin Delay | 12 ns |
| Standby Current | 25 µA |
| Product Terms per Output | 8 product terms |
| Input Logic Compatibility | CMOS and TTL compatible |
| Output Logic Compatibility | CMOS and TTL compatible |
| Configuration Technology | Electrically erasable |
| Operating Modes | Registered, combinatorial, and complex modes |
| 패키지 | 20-SOIC, 7.50 mm width |
| 실장 유형 | Surface mount |
| Package Classification | Green package |
ATF16V8CZ-12SC green package 핀 구성 가이드
ATF16V8CZ-12SC(green package 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: ATF16V8CZ-12SC.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ATF16V8CZ-12SC 적합 용도: 6 애플리케이션s: Industrial Control Logic, Automotive Interface Logic, Interface Signal Decoding, Consumer Equipment Control, Data Routing and Multiplexing, Legacy PAL-Compatible Consolidation.
Industrial Control Logic
The ATF16V8CZ-12SC fits compact industrial control logic where up to 16 inputs and 8 outputs can implement interlocks, sequencing, command decoding, and discrete state transitions. Its 12 ns maximum pin-to-pin delay supports moderate-speed combinational paths, while registered and complex modes accommodate clocked control functions. The 5 V supply and CMOS/TTL-compatible interfacing simplify connection to older logic families, although industrial temperature and transient requirements must be confirmed for the exact suffix. Verify timing margin against the master clock and ensure unused inputs are tied to defined levels before programming.
추천
Automotive Interface Logic
The ATF16V8CZ-12SC can consolidate automotive accessory, switch, and signal-routing logic when the electrical environment and qualification requirements permit the selected device grade. Eight configurable outputs and up to 16 inputs are useful for decoding switches, generating control strobes, and implementing small state machines. The -12 speed grade provides a 12 ns maximum pin-to-pin delay, but automotive use requires review of temperature range, AEC-Q100 qualification, ESD protection, transient immunity, and supplier quality requirements rather than logic functionality alone.
추천
Interface Signal Decoding
The ATF16V8CZ-12SC is useful for decoding address, command, or control signals into internal enables and data-route controls. Sixteen input terms provide enough capacity for practical Boolean decoding, while eight product terms per output support more complex equations than basic gate equivalents. The device can replace multiple PAL-compatible logic sections and supports registered operation when downstream circuits require synchronized controls. Designers should simulate the complete input truth table and verify that every output's polarity, feedback path, and registered-state behavior match the intended architecture.
추천
Consumer Equipment Control
The ATF16V8CZ-12SC can implement compact control logic for consumer products requiring mode selection, button decoding, display sequencing, or interlock functions. Its electrically erasable architecture allows the firmware-equivalent configuration to be revised during product development without replacing the device, and the 20-SOIC package supports conventional PCB assembly. The 25 µA standby specification helps when inactive-state consumption matters. For battery-operated products, calculate the complete system budget because standby current does not represent active dynamic current or leakage from external logic paths.
추천
Data Routing and Multiplexing
The ATF16V8CZ-12SC can route control and status signals or implement small multiplexers where eight outputs select or qualify multiple 5 V logic signals. Its 16-input architecture permits several candidate inputs and control terms to feed each output equation, while the 12 ns speed grade addresses moderate propagation requirements. For clocked multiplexing, use the registered mode and include setup-time, clock-to-output, and interconnect delay in the timing analysis. Confirm the programmed fuse map and test all feedback and cascading paths, since these can affect both functional behavior and timing.
추천
Legacy PAL-Compatible Consolidation
The ATF16V8CZ-12SC is appropriate for consolidating legacy 16R8 and many 20-pin combinatorial PLD functions into a single electrically erasable device. Its architecture forms a superset of common generic PLD arrangements, while the eight-macrocell structure supports combinational, registered, and complex configurations. This can simplify board assembly and permit design revisions through reprogramming. Migration still requires a detailed pin-by-pin comparison, logic-equation conversion, polarity review, and timing validation rather than assuming that every legacy fuse pattern transfers without review.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATF16V8CZ-12SC — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATF16V8CZ-12JC | ATF16V8CZ-10JC | ATF16V8CZ-15JC | ATF16V8CZ-20JC | ATF16V8CZ-10SC |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 20-SOIC | 20-SOIC - same | 20-SOIC - same | 20-SOIC - same | 20-SOIC - same | 20-SOIC - same |
| Device Architecture | ATF16V8CZ, 8 macrocells | ATF16V8CZ, 8 macrocells | ATF16V8CZ, 8 macrocells | ATF16V8CZ, 8 macrocells | ATF16V8CZ, 8 macrocells | ATF16V8CZ, 8 macrocells |
| Maximum Pin-to-Pin Delay | 12 ns | 12 ns | 10 ns | 15 ns | 20 ns | 10 ns |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Logic Compatibility | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible |
| Macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells |
| Input and Output Count | Up to 16 inputs and 8 outputs | Up to 16 inputs and 8 outputs | Up to 16 inputs and 8 outputs | Up to 16 inputs and 8 outputs | Up to 16 inputs and 8 outputs | Up to 16 inputs and 8 outputs |
| Standby Current | 25 µA | 25 µA | 25 µA | 25 µA | 25 µA | 25 µA |
| Temperature Classification | Commercial SC classification | Industrial J classification | Industrial J classification | Industrial J classification | Industrial J classification | Commercial SC classification |
주요 차별점
- Matches the 12 ns timing grade in an alternate temperature classification (vs ATF16V8CZ-12JC)
- Provides 2 ns lower propagation delay for tighter timing budgets (vs ATF16V8CZ-10JC)
- Retains the commercial temperature class with faster timing (vs ATF16V8CZ-10SC)
설계 노트
Do not treat the 12 ns pin-to-pin figure as complete system timing. For a registered path, add input setup time, clock-to-output delay, board propagation, and receiver setup time; for a combinational path, include every cascaded output and feedback segment. Select the -10 grade if the calculated margin is insufficient, and confirm that the replacement retains the 20-SOIC footprint and programmed fuse map.
Budget active and standby current separately. The 25 µA standby figure applies to the stated low-power condition, not necessarily maximum dynamic current. At 5 V, 25 µA corresponds to 0.125 mW of standby power in the specified state. External pull resistors, input leakage, and attached logic can dominate the complete board's inactive consumption, so include them in the system power budget.
Place the 20-SOIC on a footprint matching the manufacturer's package drawing, including lead pitch, body width, and solder-land geometry. Keep clock and high-fanout output traces short, provide a direct ground-return path, and isolate noisy switching nodes from logic inputs. Check every unused pin's required state in the configuration file before releasing the PCB for fabrication.
Validate the electrical-erasable configuration after programming and include the device identifier, fuse checksum, and supply condition in the manufacturing record. A successful programming operation does not prove that output polarity, registered feedback, or product-term allocation matches the intended schematic. Run boundary-pattern tests on assembled boards to detect an incorrect fuse map or package orientation.
규정 준수 정보
The manufacturer product page identifies a green package but does not provide extractable RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations.