ATTINY13-20MU - 20MHz 8-Bit AVR MCU | Microchip Technology
料号: ATTINY13-20MU ✓ 量产中ATTINY13-20MU 概述
An 8-bit microcontroller is a programmable control IC that integrates a processor core, nonvolatile program memory, data memory, and peripherals on one semiconductor die. The ATtiny family belongs to the AVR architecture, a reduced-instruction-computer design suited to compact embedded control. Within the product hierarchy, ATTINY13-20MU is a microcontroller, embedded controller, programmable logic device, and semiconductor.
The principal device ratings are a 20 MHz maximum clock, 1 KB Flash organized as 512 × 16 bits, 64 bytes of EEPROM, and 64 bytes of SRAM. The Flash memory stores the application program, EEPROM provides nonvolatile data storage, and SRAM provides volatile working memory. The integrated ADC supports analog measurements, while the 2.7 V to 5.5 V supply range accommodates common low-voltage embedded systems.
The 20-QFN-EP 4 mm × 4 mm package provides a compact surface-mount footprint and an exposed thermal pad for heat transfer through the PCB. Compared with a larger leaded package, this arrangement supports dense layouts but requires careful land-pattern and paste-control implementation. The exposed pad must be connected according to the manufacturer's recommended footprint and thermal design.
Typical uses include battery-powered sensor nodes, compact LED controllers, simple motor or actuator controls, appliance interfaces, educational electronics, and small AVR-based control boards. The 1 KB program-memory limit makes code economy especially important, while the ADC allows an application to read analog inputs without adding a separate converter.
For a new PCB, follow the manufacturer datasheet for the exact QFN land pattern, exposed-pad connection, decoupling, programming pins, and operating-voltage limits. Because the part is only 4 mm × 4 mm, inspect the assembled board for solder bridges around closely spaced pads and confirm the programming interface remains accessible.
This page combines the exact ATTINY13-20MU specifications, a focused same-package replacement assessment, engineering design notes, and application guidance to support component selection, PCB design, firmware planning, and sourcing decisions.
直接替换替代料: ATTINY13-20MU ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ATTINY13-20MU (相同外形与封装尺寸) ——差异在于 Architecture, Flash Memory, Package.
ATTINY13A-MU
✅ 直接替换联系询价
查看数据手册 →ATTINY13-20MU 最大额定值与电气特性
| Microcontroller Type | 8-bit AVR microcontroller |
| 最大时钟频率 | 20 MHz |
| Flash Memory | 1 KB (512 × 16 bits) |
| EEPROM | 64 bytes |
| SRAM | 64 bytes |
| Operating Voltage | 2.7 V to 5.5 V |
| ADC | Integrated analog-to-digital converter |
| 封装 | 20-QFN-EP (4 mm × 4 mm) |
| 安装类型 | Surface mount |
| Architecture | AVR 8-bit RISC |
| Program Memory Type | Flash |
| Nonvolatile Data Memory | 64-byte EEPROM |
| Volatile Data Memory | 64-byte SRAM |
| 引脚数 | 20 pins |
| Package Body Size | 4 mm × 4 mm |
| Exposed Thermal Pad | Present |
| RoHS 状态 | Compliant |
ATTINY13-20MU 4 mm × 4 mm 引脚配置指南
ATTINY13-20MU(4 mm × 4 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: ATTINY13-20MU.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ATTINY13-20MU 适用于 6 应用s: Battery-Powered Sensor Nodes, Compact LED Control, Small Motor and Actuator Control, Appliance and User-Interface Controls, Educational AVR Projects, Arduino-Compatible Embedded Projects.
Battery-Powered Sensor Nodes
The ATTINY13-20MU fits compact battery-powered sensor nodes because its 2.7 V to 5.5 V operating range supports low-voltage supply designs and its integrated ADC can acquire analog inputs without a separate converter. The device provides 20 MHz processing, 1 KB of Flash, 64 bytes of EEPROM, and 64 bytes of SRAM for control logic, calibration values, and short-lived working data. In a periodic-sampling design, the MCU can wake an external sensor, read an analog value, update a small state machine, and return to sleep. Firmware should minimize RAM consumption and avoid libraries that consume most of the available 1 KB program space. Regulator quiescent current, sensor standby demand, and the ATtiny sleep mode will have a greater effect on total runtime than raw CPU speed.
推荐
Compact LED Control
The ATTINY13-20MU can control compact LED indicators, status lamps, and small lighting sequences where a full-sized MCU would add unnecessary cost and board area. Its 20 MHz clock provides ample execution speed for simple timing, button handling, and digital state updates, while 1 KB of Flash can hold a focused control program. The integrated ADC can support brightness adjustment through a divider or light sensor when analog input is needed. A surface-mount 20-QFN-EP 4 mm × 4 mm package permits placement close to the LED driver circuitry. Because only 64 bytes of SRAM are available, use compact state variables and avoid buffering multiple display frames. Drive the LED through an appropriate transistor or constant-current arrangement rather than placing excessive current on a GPIO.
推荐
Small Motor and Actuator Control
The ATTINY13-20MU is suitable for small motors, solenoids, and actuator interfaces when the application requires simple sequencing rather than a high-performance real-time control loop. Its 8-bit AVR core and 20 MHz maximum clock can execute debounce logic, limit timing, state-machine transitions, and basic speed-control routines. The 1 KB Flash capacity favors concise firmware, and the 64-byte EEPROM can retain selected settings across power cycles. The MCU should not drive inductive loads directly; use a suitable transistor, flyback diode, and current-limiting arrangement. Validate stall current and switching transients against the chosen external hardware. If the design requires extensive motion tables or multiple control channels, the limited memory resources may become the deciding constraint.
推荐
Appliance and User-Interface Controls
The ATTINY13-20MU can serve as the controller for a compact appliance panel, keypad interface, or simple product configuration module. Its 20 MHz processing speed is more than adequate for debouncing switches, driving a small indicator set, and coordinating a fixed sequence of user actions. With 64 bytes of EEPROM, the device can retain a small number of configuration parameters, while 1 KB of Flash supports a narrowly defined control application. The 2.7 V to 5.5 V range permits use in low-voltage product electronics, although all external inputs must be compatible with the chosen operating voltage. A production design should include defined reset behavior, programming access, and debounce timing. The small memory footprint makes concise state handling and bounded data structures especially important.
推荐
Educational AVR Projects
The ATTINY13-20MU is well suited to educational AVR projects that teach embedded programming through compact hardware demonstrations. Students can experiment with GPIO control, timers, serial programming, and ADC-based measurements while using a device that exposes 1 KB of Flash, 64 bytes of EEPROM, and 64 bytes of SRAM. The 20 MHz clock supports responsive demonstrations without requiring a large microcontroller. Because memory is deliberately limited, the part teaches efficient coding, modular program structure, and careful register-level resource management. The 4 mm × 4 mm QFN package also introduces practical SMD assembly considerations, making it useful for reflow and inspection exercises. For breadboard-based instruction, a breakout board can simplify probing, but production artwork should follow the manufacturer footprint and exposed-pad guidance.
推荐
Arduino-Compatible Embedded Projects
The ATTINY13-20MU can serve as the core controller in small Arduino-compatible embedded projects when a compact AVR solution and modest processing requirements are sufficient. Its 8-bit architecture, 20 MHz clock, and integrated ADC support common tasks such as reading sensors, switching outputs, and running basic timing loops. The 1 KB program memory and 64 bytes of SRAM require carefully selected routines and lightweight libraries, so larger Arduino examples may not fit or execute as intended. Builders should use the exact device definition associated with ATTINY13-20MU in the programming environment and verify clock, fuse, and bootloader settings. A purpose-built breakout is convenient for prototyping, while a custom PCB should preserve the manufacturer QFN-EP land pattern, programming access, and exposed-pad thermal design.
推荐
推荐产品汇总
工程参考数据: ATTINY13-20MU ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ATTINY13A-MU |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 20-QFN-EP (4 mm × 4 mm) | 20-QFN-EP (4 mm × 4 mm) |
| Core Architecture | 8-bit AVR | 8-bit AVR |
| Maximum Clock Frequency | 20 MHz | 20 MHz |
| Flash Memory | 1 KB | 1 KB |
| EEPROM | 64 bytes | 64 bytes |
| SRAM | 64 bytes | 64 bytes |
| Operating Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| ADC | Integrated | Integrated |
关键差异点
- Exact 20 MHz performance and memory profile in a compact package (对比 ATTINY13A-MU)
- Integrated ADC reduces external analog-conversion hardware (对比 ATTINY13A-MU)
- Low-voltage operation supports compact embedded systems (对比 ATTINY13A-MU)
- Minimal package footprint supports dense PCB layouts (对比 ATTINY13A-MU)
设计说明
Use the manufacturer QFN-EP land pattern exactly and confirm whether the exposed pad is connected to ground, a supply rail, or left according to the recommended footprint. Place input and output decoupling capacitors close to their corresponding pins, and reserve short, directly routed programming signals. Inspect the 4 mm × 4 mm assembly for bridging between closely spaced terminals and avoid placing tall components where they can interfere with rework.
Design the supply rail for the selected operating range of 2.7 V to 5.5 V and account for startup, ADC reference stability, and external load current. Keep analog and digital return paths controlled so ADC readings are not unnecessarily disturbed by switching activity. A low-power design should also account for the MCU's operating mode, external sensor duty cycle, and regulator quiescent current rather than relying only on the 20 MHz clock rating.
Program-memory and RAM exhaustion are the principal practical constraints of this 1 KB Flash and 64-byte SRAM device. Avoid large frameworks and unused library functions, and test the final linked image before committing PCB production. Also verify clock and fuse settings, reset behavior, programming voltage, and pin functions against the manufacturer documentation. A same-footprint replacement cannot be approved solely from package dimensions.
The exposed pad provides the primary heat-spreading path, but its effectiveness depends on the PCB copper and assembly process. Use the manufacturer's recommended exposed-pad geometry and thermal-via arrangement rather than creating isolated vias outside the prescribed footprint. At low clock rates and low device utilization, thermal stress is generally modest, yet the exposed pad should still be soldered and connected as specified for mechanical and electrical consistency.
合规信息
The component listing explicitly identifies the ATTINY13-20MU as RoHS compliant; no additional compliance declarations are stated.