Vishay Intertechnology

DG407DW - Dual 8:1 CMOS Analog Multiplexer | Vishay

料号: DG407DW ✓ 量产中
44 V Vdss 50 ohm Rds(on) 28-pin SOIC Package
最小起订量: 1 |

DG407DW 概述

The Vishay Intertechnology DG407DW is a dual 8:1 CMOS analog multiplexer that routes one of eight differential inputs to a common differential output in each section. Its stated characteristics include 50 ohm on-resistance, 15 pC charge injection, a 200 ns transition time, 0.2 mW low power dissipation, and a maximum supply rating of 44 V. The device is offered in a 28-pin SOIC package for surface-mount PCB assembly.

An analog multiplexer is an interface IC that connects multiple input channels to a shared signal path under digital control. The DG407DW belongs to the CMOS analog switch and multiplexer hierarchy, where low on-resistance preserves signal amplitude, low charge injection reduces switching errors, and short transition time supports higher-speed routing. Its dual differential architecture suits measurement systems requiring balanced input and output connections.

Key features include two independent 8-channel differential sections, 50 ohm on-resistance, 15 pC charge injection, and a 200 ns transition time. The 44 V maximum supply rating provides additional operating headroom in industrial and instrumentation environments, while the 0.2 mW power figure highlights suitability for battery-operated and remote equipment. Reduced glitching and improved data throughput are explicit design goals of the DG407 family.

The DG407 uses digital address and enable control to determine which differential input is connected to the output. Because it is a CMOS analog multiplexer rather than a digital logic device, its useful performance is governed by analog switching parameters such as on-resistance, off leakage, charge injection, and channel-transition behavior. Designers should evaluate those parameters against the bandwidth, source impedance, and acceptable settling error of the signal being routed.

Typical uses include high-speed data-acquisition systems, audio signal routing, automatic test equipment, avionics, remote instrumentation, and battery-powered measurement products. In each case, the two differential multiplexer sections can route balanced sources while reducing wiring complexity. The manufacturer datasheet identifies low power dissipation and low on-resistance as especially useful for portable and precision signal-chain systems.

PCB design should preserve the pin orientation, supply decoupling, and analog return paths recommended by the manufacturer. Input and output traces should be kept compact and away from high-energy switching nodes, while the address and enable traces should be routed to minimize coupling into the selected analog channel. System engineers should also account for charge injection and transition time when settling data after every address change.

This product page combines the DG407DW operating characteristics with application guidance, package details, and a structured comparison against identified ordering alternatives. It is designed to help engineers select the correct mux configuration, plan layout and signal conditioning, and assess replacement options without overlooking analog switching constraints.

直接替换替代料: DG407DW ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

DG407DW-E3

✅ 直接替换
📦 28-pin SOIC
Same dual 8:1, 50-ohm configuration and 28-pin SOIC footprint; ordering suffix differs by 0% in the stated electrical ratings.

📋 参考替代料(不在目录中)

DG407DW 规格参数

Multiplexer Configuration Dual 8:1 differential analog multiplexer
Number of Circuits 2 circuits
Number of Inputs per Circuit 8 differential inputs
On-Resistance 50 ohm
Charge Injection 15 pC
Transition Time 200 ns
Power Dissipation 0.2 mW
Maximum Supply Voltage 44 V
Supply Type Single-supply capable
Technology CMOS
封装 28-pin SOIC
安装类型 Surface mount

DG407DW 28-pin soic 引脚配置指南

DG407DW(28-pin soic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

DG407DW 的 28-pin soic 封装引脚图

暂无详细引脚数据: DG407DW.

请参阅 数据手册 以查看完整引脚配置。

典型应用

DG407DW 适用于 6 应用s: High-Speed Data Acquisition, Audio Signal Routing, Automatic Test Equipment, Remote Instrumentation, Avionics Signal Routing, Battery-Powered Sensor Interfaces.

📈

High-Speed Data Acquisition

The DG407DW fits multiplexed data-acquisition systems that route balanced sensor outputs into a shared measurement chain. Its two 8:1 differential sections can reduce the number of amplifiers and ADC input channels required when several correlated inputs must be sampled sequentially. The manufacturer datasheet specifies a 200 ns transition time, 50 ohm on-resistance, and reduced glitching, which provide a concrete starting point for timing and error budgets. The acquisition system should still allow adequate settling after each address change and validate the 15 pC charge injection against the selected amplifier and ADC acquisition window.

🎧

Audio Signal Routing

The DG407DW is appropriate for balanced audio routing in test and signal-routing equipment because the manufacturer datasheet identifies audio signal switching and routing as an intended use. Each differential section can connect one of eight balanced sources to a common output, helping preserve a symmetrical signal path through the board. The 50 ohm on-resistance should be compared with the source and load impedances to determine channel loss, while the 200 ns transition time supports switching well above ordinary audio frequencies. Confirm that audio amplitudes, bandwidth, and transient expectations remain within the device's stated operating limits.

🏭

Automatic Test Equipment

The DG407DW can reduce connection complexity in automatic test equipment by routing multiple balanced test channels through a shared measurement path. Its dual differential organization allows two groups of eight inputs to be selected independently, which is useful when a test system must compare paired signals or preserve differential excitation. The manufacturer datasheet lists ATE as an intended application and highlights low on-resistance, reduced glitching, and improved data throughput. Timing should nevertheless include source settling and measurement acquisition delays, and engineers should verify that every routed signal remains within the mux's common-mode and voltage limits.

🧩

Remote Instrumentation

The DG407DW suits remote and battery-operated instrumentation where numerous balanced inputs must be routed through a compact, low-power interface. The manufacturer datasheet identifies remote instrumentation and battery-operated applications, with low power dissipation listed as 0.2 mW and low on-resistance as 50 ohm. These characteristics allow multiple channels to be selected while limiting the load introduced by the multiplexing stage. Because the device is analog rather than a signal processor, appropriate front-end amplification and filtering remain necessary to control noise, offset, and the effects of the specified 15 pC charge injection.

✈️

Avionics Signal Routing

The DG407DW can be evaluated for avionics signal routing where multiple balanced channels require compact multiplexing and rapid selection. The manufacturer datasheet explicitly lists avionics among the DG406 and DG407 applications and identifies improved data throughput and reduced glitching as design objectives. The 28-pin SOIC package provides a defined surface-mount assembly format, while the two differential sections simplify paired-signal routing. Qualification for a specific airborne program requires separate review of operating temperature, supply tolerance, reliability documentation, and applicable aerospace procurement requirements.

🔋

Battery-Powered Sensor Interfaces

The DG407DW is useful in battery-powered sensor interfaces that must select among several differential sensor channels while conserving power. Its stated 0.2 mW power dissipation and 50 ohm on-resistance provide useful initial values for comparing the mux against longer sensor wiring and higher-power switching stages. The 15 pC charge injection should be included in the settling analysis when the selected source drives a high-impedance amplifier. Designers should also verify input common-mode range, leakage, and supply behavior at the lowest battery voltage to ensure reliable operation throughout the discharge cycle.

推荐产品汇总

DG406DW Vishay Intertechnology 用于: High-Speed Data Acquisition, Audio Signal Routing, Automatic Test Equipment, Remote Instrumentation, Avionics Signal Routing, Battery-Powered Sensor Interfaces DG405DW Related CMOS analog routing family member 用于: High-Speed Data Acquisition, Audio Signal Routing, Automatic Test Equipment, Remote Instrumentation, Avionics Signal Routing, Battery-Powered Sensor Interfaces
What is the DG407DW?
The DG407DW is a dual 8:1 differential CMOS analog multiplexer from Vishay Intertechnology. According to the manufacturer datasheet, each section selects one of eight differential inputs and connects it to a common differential output. The device is specified for 50 ohm on-resistance, 15 pC charge injection, a 200 ns transition time, and operation in a 28-pin SOIC package.
What are the key specifications of DG407DW that engineers should know?
The DG407DW provides two 8:1 differential switching sections with 50 ohm on-resistance, 15 pC charge injection, a 200 ns transition time, 0.2 mW power dissipation, and a 44 V maximum supply rating. According to the manufacturer datasheet, single-supply capability, reduced glitching, and improved data throughput are central features. These specifications make the device relevant to high-speed acquisition, audio routing, test systems, and remote instrumentation.
How many channels does the DG407DW have?
The DG407DW contains two independent 8:1 differential multiplexer circuits, giving it two selectable differential outputs and eight differential input channels per section. According to the manufacturer datasheet, the common DG406 and DG407 family also supports 16-channel single-ended routing through the DG406. The DG407 specifically uses differential input and output organization for balanced signaling.
Where can I download the DG407DW datasheet PDF?
The DG407DW manufacturer datasheet is available through the Vishay document linked on this page. The document covers the DG406 and DG407 high-performance CMOS analog multiplexers, including the DG407's differential architecture, electrical characteristics, pin information, and application guidance. Use the pin-description table and ordering information in that document when assigning PCB tracks and confirming package details.
Where can I find the DG407DW pinout?
The DG407DW pinout is defined in the pin-description table of the manufacturer datasheet for the 28-pin SOIC package. Use that table to identify the differential inputs, outputs, address controls, enables, supplies, and ground connections. The package drawing is also published in the same document and should be cross-checked against the PCB footprint before layout release.
Is DG407DW suitable for high-speed data acquisition?
The DG407DW is suitable for high-speed data-acquisition routing when the system can accommodate its specified 200 ns transition time and associated settling behavior. According to the manufacturer datasheet, high-speed data acquisition is an intended application, while reduced glitching and improved data throughput support accurate channel selection. Source impedance, amplifier bandwidth, and post-switch settling must still be evaluated in the complete signal chain.
Is DG407DW suitable for audio signal routing?
The DG407DW can be used for audio signal routing because the manufacturer datasheet identifies audio signal switching and routing as an intended application. Its differential sections support balanced signal paths, while the specified 50 ohm on-resistance limits amplitude loss in the selected channel. Check the actual source impedance, load impedance, and acceptable switching transient against the application bandwidth.
Can DG407DW operate from a single supply?
The DG407DW has single-supply capability, and the manufacturer datasheet lists a maximum supply rating of 44 V. Single-supply operation simplifies many instrumentation and acquisition designs by reducing the number of required rails. Confirm the minimum and maximum operating supply voltages and the input/output common-mode limits in the manufacturer datasheet before fixing the system power architecture.
What is the on-resistance of DG407DW?
The DG407DW has a specified on-resistance of 50 ohm. According to the manufacturer datasheet, this low-resistance characteristic supports accurate signal routing by limiting voltage attenuation through the closed switch. In practice, total source resistance, load impedance, and the selected channel's on-resistance variation should be considered when calculating signal gain and input-referred error.
How much charge injection does DG407DW produce?
The DG407DW has a specified charge injection of 15 pC. According to the manufacturer datasheet, reduced charge injection and glitching are important benefits of the DG407 family. Charge injection creates a transient voltage disturbance when control inputs change state, so evaluate it against the input capacitance, amplifier settling time, and acquisition timing requirements of the selected channel.
Can DG407DW replace DG407DW-E3?
The DG407DW and DG407DW-E3 identify the same DG407 electrical device family in the 28-pin SOIC package, with the suffix representing an ordering or delivery distinction rather than a different multiplex configuration. The manufacturer datasheet and distributor records identify both as 2-circuit, 8:1, 50-ohm switch ICs. Confirm the required ordering code, delivery format, and marking before treating either suffix as an interchangeable procurement item.
What is the best drop-in replacement for DG407DW?
The closest identified drop-in ordering option is DG407DW-E3 because it uses the same 28-pin SOIC footprint and the same dual 8:1, 50-ohm DG407 configuration. No independent cross-brand substitute with verified pin compatibility was identified in the cross-reference records. Because electrical similarity alone does not prove pin compatibility, validate control logic, supply limits, common-mode range, and timing against the manufacturer datasheet before substitution.
When should I choose DG407DW over a single-ended multiplexer?
Choose the DG407DW over a single-ended multiplexer when the signal source and destination require balanced differential connections. According to the manufacturer datasheet, its differential organization routes one of eight differential inputs to a common differential output in each section. This can reduce sensitivity to common-mode interference and simplify balanced instrumentation, provided the surrounding circuitry is designed for differential signaling.
Where can I buy DG407DW online?
Use the Request a Quote form on this page to request DG407DW availability, pricing, and lead time for your required quantity and packaging. The form is the appropriate channel for current commercial terms because market pricing and inventory can change. Provide the exact DG407DW ordering designation, target quantity, and delivery requirements in the request.
What is the price of DG407DW?
Current DG407DW commercial terms are available through the Request a Quote form on this page. Request a quote with your required quantity, packaging, and shipment destination so the response reflects the exact ordering code and current supply conditions. The page does not present a static price because that value can change without notice.
What is the lead time for DG407DW?
Request the current DG407DW lead time through the Request a Quote form on this page. Include the required quantity, approved package or delivery format, and target delivery date. Lead time depends on current inventory and order configuration, so it should be confirmed for the exact DG407DW designation before committing the project schedule.

工程参考数据: DG407DW ——对比、设计指导和合规信息。

选型指南

Choose DG407DW when the design requires two independent groups of eight differential analog inputs and the source signals must share a differential output path. Its 50 ohm on-resistance, 200 ns transition time, 15 pC charge injection, and single-supply capability fit balanced measurement, audio-routing, test-equipment, avionics, and remote-instrumentation designs. DG407DW-E3 is the closest identified ordering option because it retains the same 28-pin SOIC footprint and stated electrical configuration; use it when its delivery code matches procurement requirements. If a design instead needs sixteen single-ended channels, the DG406 is functionally more appropriate but is not a pin-compatible drop-in substitute for DG407DW. No independent cross-brand drop-in option was verified, so a functional replacement should not be selected solely from similar multiplexer specifications. Confirm the complete pinout, common-mode limits, supply range, timing, and acquisition settling before finalizing a replacement.

与替代料对比

参数 本产品 DG407DW-E3
Package 28-pin SOIC 28-pin SOIC
Brand Vishay Intertechnology Vishay Intertechnology
Multiplexer Configuration Dual 8:1 differential Dual 8:1 differential
Number of Circuits 2 circuits 2 circuits
On-Resistance 50 ohm 50 ohm
Charge Injection 15 pC 15 pC
Transition Time 200 ns 200 ns
Power Dissipation 0.2 mW 0.2 mW
Maximum Supply Voltage 44 V 44 V
Supply Capability Single-supply capable Single-supply capable

关键差异点

  • Differential dual-section routing (对比 DG406DW)
  • Low stated on-resistance for signal preservation (对比 DG407DW-E3)
  • Fast channel transition and controlled charge injection (对比 DG407DW-E3)

设计说明

Treat each address transition as an analog settling event. The specified 200 ns transition time is not the complete acquisition delay: include amplifier recovery, the 15 pC charge injection transient, source impedance, and the selected channel's 50 ohm on-resistance in the system timing budget. For differential routing, keep the paired input and output traces closely coupled and provide equal-length paths where channel-to-channel skew would otherwise affect the result.

Use the manufacturer pin-description table to assign all 28 SOIC positions and cross-check the physical pin-1 orientation against the PCB footprint. Place the supply bypass capacitor close to the device's supply and ground pins, and keep high-impedance routing short to minimize leakage and induced error. Avoid placing switching-node copper directly beneath the analog output or control traces because coupling can appear as extra charge injection or channel-to-channel glitching.

Do not equate a 50 ohm on-resistance rating with a source-impedance requirement. The total channel resistance includes the selected switch resistance and all series source impedance, while off-channel leakage and input capacitance can affect the next conversion after switching. Also verify common-mode limits and supply polarity for both single-ended and differential operation; the 44 V maximum supply rating is an absolute limit, not a recommended operating point.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

Compliance status was not stated in the cited product and distributor information. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status from the current manufacturer documentation or declaration.

相关搜索

DG407DW datasheet DG407DW pinout DG407DW datasheet pdf DG407DW equivalent DG407DW replacement DG407DW cross reference DG407DW footprint DG407DW spice model DG407DW price DG407DW stock Vishay DG407DW DG407DW 50 ohm on resistance DG407DW 28 SOIC pinout DG407DW data acquisition application DG407DW vs DG406DW

相关元器件 & 术语

Vishay Intertechnology DG407DW DG407DW-E3 DG406DW DG405DW analog multiplexer analog switch CMOS differential multiplexer single-ended multiplexer interface IC on-resistance charge injection transition time 28-pin SOIC SOIC package family surface-mount package high-speed data acquisition automatic test equipment audio signal routing remote instrumentation avionics single-supply capability reduced glitching improved data throughput
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情