DP83865DVH/NOPB - 1GbE 8/8 Ethernet PHY | Texas Instruments
料号: DP83865DVH/NOPB ✓ 量产中DP83865DVH/NOPB 概述
An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts digital data into electrical signaling for a physical copper network and recovers incoming signaling into digital data. Within the product hierarchy, an Ethernet PHY is an interface IC connected between a network controller or processor and a magnetics-based Ethernet interface. The DP83865DVH/NOPB combines the higher-layer physical coding sublayer, medium-access control physical medium dependent sublayer, and copper PHY functions in one device.
The DP83865DVH/NOPB supports data rates up to 1 Gbit/s and uses an 8/8 transceiver arrangement for four transmit and four receive channels. It operates across a listed supply-voltage range of 1.71 V to 3.465 V and has a specified operating-temperature range of 0°C to +70°C. Its 128-pin PQFP package measures approximately 14 mm by 20 mm and uses surface-mount assembly.
At the device level, the DP83865 family combines 10BASE-T, 100BASE-TX, and 1000BASE-T support with an integrated 8/8 driver and receiver configuration. This integration allows a system designed around a single Ethernet PHY to support multiple copper Ethernet speed modes while limiting the number of discrete line-driver and receiver components required on the board.
Typical applications include industrial Ethernet gateways, network switches, routers, set-top equipment, embedded servers, printer controllers, and other systems that connect a digital processor to a 10/100/1000BASE-T network. In these designs, the PHY normally interfaces with an Ethernet magnetics module through transformer-coupled differential pairs, while a network controller or communications processor handles the MAC and protocol layers.
A critical layout requirement is a carefully controlled high-speed differential network between the PHY and Ethernet transformer. Keep the transmit and receive pairs routed with continuous impedance, minimize stub lengths, use symmetric routing, and place the magnetic device close to the network connector. Power and decoupling networks should likewise be arranged to isolate sensitive transceiver circuits from switching and high-current loads.
This product page organizes the DP83865DVH/NOPB specifications, verified drop-in replacement information, application guidance, and design considerations into an engineering-focused reference. It also distinguishes the original 128-PQFP device from the newer DP83867IRPAPR identified as a pin-compatible replacement, helping engineers evaluate whether the electrical and firmware requirements of an existing design permit a direct substitution.
直接替换替代料: DP83865DVH/NOPB ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: DP83865DVH/NOPB (相同外形与封装尺寸) ——差异在于 Operating Temperature Range, Product Type.
DP83867IRPAPR
✅ 直接替换联系询价
查看数据手册 →DP83865DVH/NOPB 规格参数
| Product Type | Gigabit Ethernet physical-layer transceiver |
| Supported Ethernet Protocols | 10BASE-T, 100BASE-TX, and 1000BASE-T |
| Maximum Data Rate | 1 Gbit/s |
| Driver and Receiver Configuration | 8/8 |
| Number of Transceivers | 1 |
| Supply Voltage Range | 1.71 V to 3.465 V |
| Alternate Listed Supply Voltage Range | 2.375 V to 3.465 V |
| 工作温度范围 | 0°C to +70°C |
| Package Type | 128-PQFP |
| Package Dimensions | 14 mm x 20 mm |
| 引脚数 | 128 pins |
| 安装类型 | Surface mount |
| Integrated Physical Functions | PCS, PMA, and PMD sublayers |
DP83865DVH/NOPB 14 mm x 20 mm 引脚配置指南
DP83865DVH/NOPB(14 mm x 20 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: DP83865DVH/NOPB.
请参阅 数据手册 以查看完整引脚配置。
典型应用
DP83865DVH/NOPB 适用于 6 应用s: Industrial Ethernet Gateway, Network Switch, Router, Embedded Server, Set-Top Box, Networked Printer Controller.
Industrial Ethernet Gateway
The DP83865DVH/NOPB fits an industrial Ethernet gateway that must support 10, 100, and 1000 Mbit/s copper links while controlling board area. Its 1 Gbit/s capability, integrated PCS, PMA, and PMD functions, and 8/8 transceiver arrangement provide one physical-layer solution for multiple Ethernet rates. The device’s 0°C to +70°C range suits commercial-temperature gateway designs, while systems requiring wider environmental limits should use a suitably rated PHY. Place the Ethernet magnetics close to the shielded connector and route the differential pairs as controlled-impedance lines.
推荐
Network Switch
A multiport network switch can use the DP83865DVH/NOPB when each copper port requires 10/100/1000BASE-T support and compact board construction. Its maximum 1 Gbit/s data rate and integrated medium-access-control physical functions eliminate the need for separate PMD devices on each port. The 128-PQFP footprint requires careful fanout and layer planning in a multilayer switch PCB. Maintain symmetry between each transmit and receive pair, minimize connector-to-PHY distance, and provide low-impedance supply connections with local high-frequency decoupling.
推荐
Router
The DP83865DVH/NOPB is appropriate for a router with a copper WAN or LAN interface supporting 10BASE-T, 100BASE-TX, or 1000BASE-T. Its integrated PCS, PMA, and PMD layers provide the physical Ethernet interface while the host processor handles routing and higher-level traffic management. The 1.71 V to 3.465 V listed supply range supports low-voltage system architectures. Use manufacturer reference layouts to control differential-pair impedance and keep the transformer and line-side protection components close to the external network connector.
推荐
Embedded Server
The DP83865DVH/NOPB can provide the physical layer for an embedded server or single-board computer that needs backward-compatible 10/100/1000BASE-T connectivity. The single integrated PHY avoids a separate physical-layer device for each supported copper speed, while the 8/8 driver-and-receiver configuration supports the device’s differential channels. In a dense embedded board, provide uninterrupted ground planes beneath the 128-lead footprint and route each high-speed pair away from clocks, switching regulators, and memory buses.
推荐
Set-Top Box
The DP83865DVH/NOPB is suitable for a set-top box requiring one or more copper Ethernet connections with automatic support for 10, 100, and 1000 Mbit/s. Its 1 Gbit/s maximum data rate accommodates local-network transfers, and the integrated PCS, PMA, and PMD blocks reduce the external component count associated with the Ethernet physical layer. The commercial 0°C to +70°C range matches many indoor set-top environments. Follow the manufacturer’s isolation, magnetics, and reference-layout guidance to preserve signal and surge-performance margins.
推荐
Networked Printer Controller
A networked printer controller can use the DP83865DVH/NOPB to connect a printer main board through copper Ethernet while retaining compatibility with slower 10BASE-T and 100BASE-TX networks. The device supports rates through 1 Gbit/s and consolidates the physical medium access, physical coding, and medium-dependent functions into one package. Because the 128-PQFP lead pitch limits routing flexibility, use a multilayer PCB with short escape traces, matched pair lengths, and a low-impedance ground reference beneath the PHY and magnetics area.
推荐
推荐产品汇总
工程参考数据: DP83865DVH/NOPB ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | DP83867IRPAPR |
|---|---|---|
| Package | 128-PQFP | 128-PQFP |
| Brand | Texas Instruments | Texas Instruments |
| Supply Voltage Range | 1.71 V to 3.465 V | 1.71 V to 3.465 V |
| Number of Pins | 128 pins | 128 pins |
关键差异点
- Broad copper Ethernet speed support in one physical-layer device (对比 DP83867IRPAPR)
- Established 8/8 driver-and-receiver configuration (对比 DP83867IRPAPR)
- Mechanical compatibility with a documented newer-family replacement (对比 DP83867IRPAPR)
设计说明
Route every differential Ethernet pair as a controlled-impedance transmission line with continuous reference planes, symmetrical geometry, and no unnecessary stubs. Follow the Texas Instruments DP83865 reference layout for pair breakout from the 128-PQFP, component placement, and separation between transmit and receive channels. Place the Ethernet magnetics close to the connector so the connector-to-PHY path remains short and protected from external cable transients.
Use a multilayer PCB with a continuous ground plane beneath the PHY and uninterrupted supply planes around the 128-lead footprint. Place required bypass capacitors at their designated power pins and keep their current loops compact. Separate noisy switching-regulator paths from the differential network and sensitive transceiver return-current paths. Confirm layer-stack impedance and component clearances against the manufacturer application guidance before fabrication.
A shared package and supply range do not by themselves prove that two Ethernet PHYs are interchangeable. When evaluating DP83867IRPAPR for a DP83865DVH/NOPB design, compare register addresses, initialization sequence, clock requirements, interrupt polarity, autonegotiation behavior, cable diagnostics, and the host-interface timing. Preserve the original footprint only after software and schematic checks confirm that the replacement is acceptable for the intended product.
Keep the PHY-to-magnetics copper section short and isolated from noisy digital and power-conversion circuitry. Use manufacturer-recommended magnetic-module and line-side protection arrangements, and maintain a low-impedance return path beneath each differential pair. Avoid routing Ethernet signals parallel to switching-node traces or high-current supply paths for extended distances, because inductive coupling can degrade the 1 Gbit/s signal margin.
合规信息
The DP83865DVH/NOPB is an Ethernet interface IC rather than an automotive-qualified device; no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement is included in the available product information.