DS90CR581MTD 24-Bit LVDS FPD Transmitter | TI
料号: DS90CR581MTD ✓ 量产中DS90CR581MTD 概述
An LVDS transmitter is a high-speed interface device that transmits balanced differential signals over a reduced-voltage physical layer. In the display hierarchy, the DS90CR581MTD is a display interface controller, an interface IC, and ultimately a semiconductor-level signal-conditioning device. Parallel CMOS pixel data enters the transmitter, an internal phase-locked loop derives the transmitted clock, and four differential LVDS lanes carry pixel information plus synchronized data-strobe information.
Key features include support for 24-bit color data, four LVDS outputs, transmission of a phase-locked clock in parallel, rising-edge data strobes, and a power-down mode. The narrow-bus architecture replaces many single-ended interconnects with fewer differential pairs, reducing board routing and cable demands. The internal PLL requires no external components according to the product documentation, simplifying system implementation. A 290 mV LVDS swing also supports low-EMI operation compared with larger single-ended transitions.
The DS90CR581MTD is positioned for legacy flat-panel LCD systems, including monitor and digital display controllers that provide TTL or CMOS pixel data and require conversion to an LVDS panel link. The transmitter handles 28 bits of source data, allowing the system to carry 24 color bits together with synchronization and control information. Its phase-locked transmit clock helps the receiving panel interface recover a stable timing reference.
Use the manufacturer datasheet pin-description table to assign PCB tracks because a complete 56-pin map is not reproduced on this page. Confirm panel-side clock polarity, lane mapping, and input data-strobe timing before releasing a layout. The 56-TSSOP package also requires careful power and ground-plane arrangement to prevent data corruption at high pixel-clock rates.
This page organizes the display-interface details, application fit, package information, and verified comparison points into a practical engineering reference for LCD panel-link designers.
直接替换替代料: DS90CR581MTD ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料DS90CR581MTD 规格参数
| Product Type | LVDS Transmitter |
| Application | 24-Bit Color Flat Panel Display Link |
| Input Data | 28 bits CMOS/TTL |
| Color Data Width | 24 bits |
| LVDS Data Streams | 4 |
| Maximum Data Rate | 140 MB/s |
| LVDS Output Swing | 290 mV |
| Clock Transmission | Phase-locked transmit clock transmitted in parallel |
| Data Strobe Edge | Rising edge |
| Power-Down Mode | Supported |
| PLL External Components | None required |
| LVDS Standard Compatibility | TIA/EIA-644 |
| Temperature Grade | Commercial |
| Package Type | 56-lead TSSOP |
| Package Shape | Rectangular |
| Terminal Form | Gull wing |
| 安装类型 | Surface mount |
DS90CR581MTD rectangular 引脚配置指南
DS90CR581MTD(rectangular 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: DS90CR581MTD.
请参阅 数据手册 以查看完整引脚配置。
典型应用
DS90CR581MTD 适用于 6 应用s: Legacy LCD Monitor Panel Interface, Industrial Flat-Panel Display Controller, TTL-to-LVDS Video Adapter, Digital Signage Panel Link, Medical Display Panel Interface, Test and Measurement Display Module.
Legacy LCD Monitor Panel Interface
The DS90CR581MTD fits an LCD monitor design in which the display controller still outputs parallel CMOS/TTL pixel data but the panel expects LVDS. The transmitter accepts 28 source bits, supports 24-bit color information, and produces four differential data streams with a nominal 290 mV swing. That arrangement reduces the number of panel interconnects compared with a wide parallel bus. The 140 MB/s maximum data rate must be checked against the target resolution and refresh rate, including timing margins for the selected panel timing controller.
Industrial Flat-Panel Display Controller
The DS90CR581MTD can bridge a legacy industrial display controller to an LVDS panel that requires low-EMI differential signaling. Its four-lane narrow-bus architecture helps reduce connector and cable requirements, while the transmitted phase-locked clock gives the panel interface a synchronized timing reference. For factory-floor equipment, confirm operating-temperature limits, panel timing, cable length, and grounding strategy before layout release. Commercial temperature grade is documented, and additional environmental qualification should be reviewed for the finished system.
TTL-to-LVDS Video Adapter
A TTL-to-LVDS adapter built around the DS90CR581MTD is useful when an existing video or graphics controller cannot directly drive a differential panel. The device converts 28 CMOS/TTL bits into four LVDS streams and provides a parallel phase-locked transmit clock. Its low-voltage differential output reduces EMI relative to a comparably wide single-ended link and limits the number of traces crossing between logic and panel sections of the board. Panel lane order, clock polarity, and data-strobe timing must be verified against both endpoint devices.
Digital Signage Panel Link
The DS90CR581MTD can support a digital-signage panel that retains a legacy parallel display interface but benefits from a lower-EMI connection to the panel electronics. Four LVDS outputs carry the pixel stream at up to 140 MB/s, and the 290 mV swing targets the TIA/EIA-644 signaling approach. Design the system so the controller timing matches the panel's accepted format, then validate the complete chain with long-cable and power-sequencing tests. Cable length and connector construction influence achievable data integrity more than the nominal swing alone.
Medical Display Panel Interface
The DS90CR581MTD may be used in a medical monitoring display when the display module retains a legacy TTL pixel interface and the system can supply a deterministic LVDS link. Differential signaling reduces common-mode noise and helps maintain image integrity in panels exposed to nearby switching or high-current circuitry. The transmitter itself does not provide medical certification, so the finished display requires appropriate validation. Review panel timing, isolation strategy, fault behavior, and EMI performance as part of the complete system assessment.
Test and Measurement Display Module
Instrumentation and test equipment can use the DS90CR581MTD when a legacy graphics engine requires conversion to an LVDS panel connection. The integrated four-channel transmitter reduces the component count compared with building a complete LVDS serialization path from discrete logic. The internal PLL requires no external components according to the manufacturer feature list, simplifying implementation. Keep the transmitter's clock and data routing isolated from high-current switching stages, and verify the panel's supported resolution, refresh rate, and synchronization inputs before selecting the module.
工程参考数据: DS90CR581MTD ——对比、设计指导和合规信息。
选型指南
设计说明
Route the four LVDS differential pairs as tightly coupled pairs with matched length and continuous reference planes beneath them. Keep the pairs away from switching-regulator inductors, crystal circuits, and high-current return paths. Because the device uses only a 290 mV nominal differential swing, unnecessary loop area and crosstalk can matter more than they would with a large-amplitude single-ended interface. Confirm the final stack-up and trace geometry against the manufacturer layout guidance.
Place bypass capacitors immediately across the device supply and ground pins, using the values and connection sequence specified in the manufacturer datasheet. Route the transmitter return current through the same reference plane as the outgoing LVDS pairs to limit loop impedance. If the panel link shares a board with switching converters or display backlight drivers, separate their high-current paths and verify supply noise at the transmitter with an oscilloscope under worst-case pixel activity.
Validate lane mapping, transmitted-clock polarity, and rising-edge data-strobe timing with the exact panel receiver rather than assuming compatibility from connector pin order alone. The four data streams and parallel phase-locked clock must meet the receiver's setup and hold requirements at the maximum supported data rate. Include eye-quality, jitter, and power-sequencing checks with representative cables and connectors because transmitter specifications alone do not guarantee end-to-end margin.
合规信息
The commercial-temperature classification and TIA/EIA-644 signaling compatibility are documented. RoHS, REACH, halogen-free, lead-free, and conflict-minerals statuses were not stated in the product information and remain unknown.