DS90CR581MTD 24-Bit LVDS FPD Transmitter | TI
부품 번호: DS90CR581MTD ✓ 활성DS90CR581MTD 개요
An LVDS transmitter is a high-speed interface device that transmits balanced differential signals over a reduced-voltage physical layer. In the display hierarchy, the DS90CR581MTD is a display interface controller, an interface IC, and ultimately a semiconductor-level signal-conditioning device. Parallel CMOS pixel data enters the transmitter, an internal phase-locked loop derives the transmitted clock, and four differential LVDS lanes carry pixel information plus synchronized data-strobe information.
Key features include support for 24-bit color data, four LVDS outputs, transmission of a phase-locked clock in parallel, rising-edge data strobes, and a power-down mode. The narrow-bus architecture replaces many single-ended interconnects with fewer differential pairs, reducing board routing and cable demands. The internal PLL requires no external components according to the product documentation, simplifying system implementation. A 290 mV LVDS swing also supports low-EMI operation compared with larger single-ended transitions.
The DS90CR581MTD is positioned for legacy flat-panel LCD systems, including monitor and digital display controllers that provide TTL or CMOS pixel data and require conversion to an LVDS panel link. The transmitter handles 28 bits of source data, allowing the system to carry 24 color bits together with synchronization and control information. Its phase-locked transmit clock helps the receiving panel interface recover a stable timing reference.
Use the manufacturer datasheet pin-description table to assign PCB tracks because a complete 56-pin map is not reproduced on this page. Confirm panel-side clock polarity, lane mapping, and input data-strobe timing before releasing a layout. The 56-TSSOP package also requires careful power and ground-plane arrangement to prevent data corruption at high pixel-clock rates.
This page organizes the display-interface details, application fit, package information, and verified comparison points into a practical engineering reference for LCD panel-link designers.
드롭인 대체품: DS90CR581MTD — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청DS90CR581MTD 사양
| Product Type | LVDS Transmitter |
| Application | 24-Bit Color Flat Panel Display Link |
| Input Data | 28 bits CMOS/TTL |
| Color Data Width | 24 bits |
| LVDS Data Streams | 4 |
| Maximum Data Rate | 140 MB/s |
| LVDS Output Swing | 290 mV |
| Clock Transmission | Phase-locked transmit clock transmitted in parallel |
| Data Strobe Edge | Rising edge |
| Power-Down Mode | Supported |
| PLL External Components | None required |
| LVDS Standard Compatibility | TIA/EIA-644 |
| Temperature Grade | Commercial |
| Package Type | 56-lead TSSOP |
| Package Shape | Rectangular |
| Terminal Form | Gull wing |
| 실장 유형 | Surface mount |
DS90CR581MTD rectangular 핀 구성 가이드
DS90CR581MTD(rectangular 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: DS90CR581MTD.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
DS90CR581MTD 적합 용도: 6 애플리케이션s: Legacy LCD Monitor Panel Interface, Industrial Flat-Panel Display Controller, TTL-to-LVDS Video Adapter, Digital Signage Panel Link, Medical Display Panel Interface, Test and Measurement Display Module.
Legacy LCD Monitor Panel Interface
The DS90CR581MTD fits an LCD monitor design in which the display controller still outputs parallel CMOS/TTL pixel data but the panel expects LVDS. The transmitter accepts 28 source bits, supports 24-bit color information, and produces four differential data streams with a nominal 290 mV swing. That arrangement reduces the number of panel interconnects compared with a wide parallel bus. The 140 MB/s maximum data rate must be checked against the target resolution and refresh rate, including timing margins for the selected panel timing controller.
Industrial Flat-Panel Display Controller
The DS90CR581MTD can bridge a legacy industrial display controller to an LVDS panel that requires low-EMI differential signaling. Its four-lane narrow-bus architecture helps reduce connector and cable requirements, while the transmitted phase-locked clock gives the panel interface a synchronized timing reference. For factory-floor equipment, confirm operating-temperature limits, panel timing, cable length, and grounding strategy before layout release. Commercial temperature grade is documented, and additional environmental qualification should be reviewed for the finished system.
TTL-to-LVDS Video Adapter
A TTL-to-LVDS adapter built around the DS90CR581MTD is useful when an existing video or graphics controller cannot directly drive a differential panel. The device converts 28 CMOS/TTL bits into four LVDS streams and provides a parallel phase-locked transmit clock. Its low-voltage differential output reduces EMI relative to a comparably wide single-ended link and limits the number of traces crossing between logic and panel sections of the board. Panel lane order, clock polarity, and data-strobe timing must be verified against both endpoint devices.
Digital Signage Panel Link
The DS90CR581MTD can support a digital-signage panel that retains a legacy parallel display interface but benefits from a lower-EMI connection to the panel electronics. Four LVDS outputs carry the pixel stream at up to 140 MB/s, and the 290 mV swing targets the TIA/EIA-644 signaling approach. Design the system so the controller timing matches the panel's accepted format, then validate the complete chain with long-cable and power-sequencing tests. Cable length and connector construction influence achievable data integrity more than the nominal swing alone.
Medical Display Panel Interface
The DS90CR581MTD may be used in a medical monitoring display when the display module retains a legacy TTL pixel interface and the system can supply a deterministic LVDS link. Differential signaling reduces common-mode noise and helps maintain image integrity in panels exposed to nearby switching or high-current circuitry. The transmitter itself does not provide medical certification, so the finished display requires appropriate validation. Review panel timing, isolation strategy, fault behavior, and EMI performance as part of the complete system assessment.
Test and Measurement Display Module
Instrumentation and test equipment can use the DS90CR581MTD when a legacy graphics engine requires conversion to an LVDS panel connection. The integrated four-channel transmitter reduces the component count compared with building a complete LVDS serialization path from discrete logic. The internal PLL requires no external components according to the manufacturer feature list, simplifying implementation. Keep the transmitter's clock and data routing isolated from high-current switching stages, and verify the panel's supported resolution, refresh rate, and synchronization inputs before selecting the module.
엔지니어링 참조 데이터: DS90CR581MTD — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
설계 노트
Route the four LVDS differential pairs as tightly coupled pairs with matched length and continuous reference planes beneath them. Keep the pairs away from switching-regulator inductors, crystal circuits, and high-current return paths. Because the device uses only a 290 mV nominal differential swing, unnecessary loop area and crosstalk can matter more than they would with a large-amplitude single-ended interface. Confirm the final stack-up and trace geometry against the manufacturer layout guidance.
Place bypass capacitors immediately across the device supply and ground pins, using the values and connection sequence specified in the manufacturer datasheet. Route the transmitter return current through the same reference plane as the outgoing LVDS pairs to limit loop impedance. If the panel link shares a board with switching converters or display backlight drivers, separate their high-current paths and verify supply noise at the transmitter with an oscilloscope under worst-case pixel activity.
Validate lane mapping, transmitted-clock polarity, and rising-edge data-strobe timing with the exact panel receiver rather than assuming compatibility from connector pin order alone. The four data streams and parallel phase-locked clock must meet the receiver's setup and hold requirements at the maximum supported data rate. Include eye-quality, jitter, and power-sequencing checks with representative cables and connectors because transmitter specifications alone do not guarantee end-to-end margin.
규정 준수 정보
The commercial-temperature classification and TIA/EIA-644 signaling compatibility are documented. RoHS, REACH, halogen-free, lead-free, and conflict-minerals statuses were not stated in the product information and remain unknown.