INA132U/2K5 - 2.5 Gain Differential Amplifier | Texas Instruments
料号: INA132U/2K5 ✓ 量产中INA132U/2K5 概述
A difference amplifier is an analog signal-conditioning circuit that subtracts one input voltage from another and amplifies the result. The INA132U/2K5 belongs to the instrumentation-amplifier and precision-differential-amplifier hierarchy, where accurate gain and common-mode rejection are essential for converting small sensor outputs into signals suitable for analog-to-digital converters, control systems, and measurement equipment.
The integrated resistor network gives the /2K5 ordering option a fixed gain of 2.5, while laser trimming supports accurate gain and high common-mode rejection. The amplifier operates from a single 2.7 V to 36 V supply and can also be used with split supplies where the input and output voltages remain within the device's electrical limits. Its low-power design makes it suitable for battery-powered and industrial instrumentation systems.
The INA132U/2K5 accepts input signals through differential IN+ and IN− terminals and provides the amplified difference at OUT. A reference terminal permits the output to be shifted relative to a chosen voltage when the application cannot use a ground-centered signal. The internal architecture simplifies PCB design by reducing the number of external precision resistors normally required for a discrete difference amplifier.
Typical uses include bridge-transducer excitation and readout, precision current sensing, industrial process monitoring, battery-powered sensing, and low-level differential signal acquisition. Because the device has a fixed 2.5 gain, engineers should verify that the required signal gain, common-mode range, output swing, and supply voltage match before placing it in a new design.
Layout quality directly affects differential-signal performance. Route the IN+ and IN− paths as a closely matched pair, keep the reference and output nodes away from switching-current paths, and use a low-noise supply arrangement with local bypass capacitors. Confirm input and output common-mode limits at the operating temperature and check the final gain tolerance against the system measurement budget.
This page combines ordering information, technical limits, drop-in replacement analysis, comparison data, and application-specific design guidance. It is intended to help engineers identify whether the INA132U/2K5 provides the required gain, supply range, package, and replacement compatibility before committing a board layout.
直接替换替代料: INA132U/2K5 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: INA132U/2K5 (相同外形与封装尺寸) ——差异在于 Device Type, Operating Temperature Range.
INA132UA/2K5
✅ 直接替换📋 参考替代料(不在目录中)
INA132U/2K5 最大额定值与电气特性
| Device Type | Single-supply difference amplifier |
| Number of Circuits | 1 circuit |
| Fixed Gain | 2.5 V/V |
| Supply Voltage Range | 2.7 V to 36 V |
| Typical Total Supply Voltage | ±15 V |
| Minimum Total Supply Voltage | ±1.35 V |
| Maximum Total Supply Voltage | ±18 V |
| 工作温度范围 | -40 °C to +85 °C |
| 封装 | 8-pin SOIC |
| 安装类型 | Surface mount |
INA132U/2K5 8-pin soic 引脚配置指南
INA132U/2K5(8-pin soic 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: INA132U/2K5.
请参阅 数据手册 以查看完整引脚配置。
典型应用
INA132U/2K5 适用于 6 应用s: Bridge Transducer Signal Conditioning, Precision Shunt Current Sensing, Battery-Powered Sensor Interface, Industrial Process Monitoring, Low-Level Differential Signal Acquisition, Instrumentation Signal Conditioning.
Bridge Transducer Signal Conditioning
The INA132U/2K5 is well suited to bridge-transducer readout because its integrated resistor network provides a fixed gain of 2.5 and rejects common-mode voltage present on both bridge inputs. Connect the bridge excitation across the device supply arrangement and route IN+ and IN− as a matched pair to minimize added differential error. The 2.7 V to 36 V supply range supports low-voltage excitation as well as industrial systems. Before deployment, verify the bridge output at zero and full scale, check the output against the available supply headroom, and account for the amplifier's gain error in the measurement budget.
推荐
Precision Shunt Current Sensing
The INA132U/2K5 can amplify the small differential voltage generated by a current shunt while rejecting the larger common-mode voltage on the shunt nodes. Its 2.5 V/V fixed gain increases the measurement signal without requiring an external gain network. Use Kelvin routing from the shunt to IN+ and IN− so copper and connector resistance do not appear as sensed voltage. The single-supply operation supports compact battery-powered monitoring, but the system must preserve output headroom and remain within the input common-mode range during startup and fault conditions.
推荐
Battery-Powered Sensor Interface
The INA132U/2K5 fits low-power sensor interfaces because it operates from a single supply beginning at 2.7 V and integrates the precision gain-setting network. It can amplify a differential sensor output while operating from a compact 3.3 V rail, reducing the need for external resistors and associated board area. Power-system designers should still calculate operating current from the manufacturer specifications and verify shutdown behavior separately because the INA132 is intended for continuous low-power signal conditioning rather than duty-cycled operation.
推荐
Industrial Process Monitoring
Industrial process monitoring benefits from the INA132U/2K5's fixed 2.5 gain and integrated precision resistor network because sensor outputs can be conditioned close to the measurement source. The 2.7 V to 36 V supply range allows use in both compact instrumentation and higher-voltage industrial systems when the rails are otherwise suitable. Place the amplifier near the sensor connector, maintain symmetrical differential routing, and isolate it from motor-control and relay-switching nodes. Verify the process input range, sensor excitation requirements, and required analog-to-digital converter full-scale voltage before finalizing the signal chain.
推荐
Low-Level Differential Signal Acquisition
The INA132U/2K5 is useful when a small differential signal must be elevated before conversion or comparison, particularly when the source contains a much larger common-mode component. Its fixed 2.5 gain preserves a compact implementation while the internal precision network improves consistency between devices. Use short, matched traces and a stable reference arrangement to minimize offset and common-mode conversion. Confirm that the amplified signal remains inside the output swing, and account for the 2.5 multiplication when choosing downstream analog-to-digital converter ranges.
推荐
Instrumentation Signal Conditioning
The INA132U/2K5 provides a practical first stage for instrumentation signals that require differential sensing and fixed amplification. Its 8-pin SOIC package supports conventional surface-mount assembly, and the integrated gain network reduces component count compared with a discrete precision difference amplifier. Designers should assess offset, gain tolerance, common-mode rejection, and output range for each measurement class using the manufacturer limits. For high-gain or highly variable systems, a programmable or higher-gain instrumentation amplifier may offer more adjustment flexibility than this fixed 2.5-gain device.
推荐
推荐产品汇总
工程参考数据: INA132U/2K5 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | INA132UA/2K5 |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC |
| Device Type | Low-power, single-supply difference amplifier | Low-power, single-supply difference amplifier |
| Fixed Gain | 2.5 V/V | 2.5 V/V |
| Number of Circuits | 1 circuit | 1 circuit |
| Supply Voltage Range | 2.7 V to 36 V | 2.7 V to 36 V |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C |
| Mounting Type | Surface mount | Surface mount |
| Integrated Precision Resistor Network | Yes | Yes |
| Ordering Difference | INA132U/2K5 ordering code | INA132UA/2K5 ordering code; delivery format differs |
关键差异点
- Fixed 2.5 gain with integrated precision resistor network (对比 INA132UA/2K5)
- Single-supply operation across a wide voltage range (对比 INA132UA/2K5)
- Surface-mount instrumentation footprint (对比 INA132UA/2K5)
设计说明
Route IN+ and IN− as a closely matched differential pair and connect both amplifier inputs to the sensor or shunt with equal trace lengths and symmetric geometry. Current flowing through mismatched input resistance creates differential error even when the amplifier's common-mode rejection is high. Place the device near the source, minimize loop area, and keep switching-node copper and high-current return paths away from the differential inputs.
Place the supply bypass capacitor immediately adjacent to the amplifier's supply and ground pins, using the shortest electrical path available. Keep the supply return above or adjacent to the sensitive input traces rather than sharing a noisy return segment with relays, motors, or LEDs. Validate the input common-mode and output-swing limits with the actual 2.7 V to 36 V operating rail because the usable signal range is narrower than the supply range.
Do not select a different INA132 gain version solely because it uses the same 8-pin SOIC outline. The base INA132 and INA132UA/2K5 family ordering options can have different gain behavior, while INA143UA and AD8278ARZ may use different gain architectures. A physical footprint match does not guarantee signal-level compatibility; confirm the gain equation, common-mode range, output swing, supply limits, and reference-pin use before substitution.
合规信息
The manufacturer identifies the INA132U/2K5 as active, but specific environmental and material-compliance statements require confirmation from the current manufacturer documentation or declaration.