INA132U/2K5 - 2.5 Gain Differential Amplifier | Texas Instruments
N.º de pieza: INA132U/2K5 ✓ ActivoINA132U/2K5 Descripción general
A difference amplifier is an analog signal-conditioning circuit that subtracts one input voltage from another and amplifies the result. The INA132U/2K5 belongs to the instrumentation-amplifier and precision-differential-amplifier hierarchy, where accurate gain and common-mode rejection are essential for converting small sensor outputs into signals suitable for analog-to-digital converters, control systems, and measurement equipment.
The integrated resistor network gives the /2K5 ordering option a fixed gain of 2.5, while laser trimming supports accurate gain and high common-mode rejection. The amplifier operates from a single 2.7 V to 36 V supply and can also be used with split supplies where the input and output voltages remain within the device's electrical limits. Its low-power design makes it suitable for battery-powered and industrial instrumentation systems.
The INA132U/2K5 accepts input signals through differential IN+ and IN− terminals and provides the amplified difference at OUT. A reference terminal permits the output to be shifted relative to a chosen voltage when the application cannot use a ground-centered signal. The internal architecture simplifies PCB design by reducing the number of external precision resistors normally required for a discrete difference amplifier.
Typical uses include bridge-transducer excitation and readout, precision current sensing, industrial process monitoring, battery-powered sensing, and low-level differential signal acquisition. Because the device has a fixed 2.5 gain, engineers should verify that the required signal gain, common-mode range, output swing, and supply voltage match before placing it in a new design.
Layout quality directly affects differential-signal performance. Route the IN+ and IN− paths as a closely matched pair, keep the reference and output nodes away from switching-current paths, and use a low-noise supply arrangement with local bypass capacitors. Confirm input and output common-mode limits at the operating temperature and check the final gain tolerance against the system measurement budget.
This page combines ordering information, technical limits, drop-in replacement analysis, comparison data, and application-specific design guidance. It is intended to help engineers identify whether the INA132U/2K5 provides the required gain, supply range, package, and replacement compatibility before committing a board layout.
Alternativas directas para INA132U/2K5 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con INA132U/2K5 (mismo factor de forma y huella) — difiere en Device Type, Operating Temperature Range.
INA132UA/2K5
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
INA132U/2K5 Valores máximos y características eléctricas
| Device Type | Single-supply difference amplifier |
| Number of Circuits | 1 circuit |
| Fixed Gain | 2.5 V/V |
| Supply Voltage Range | 2.7 V to 36 V |
| Typical Total Supply Voltage | ±15 V |
| Minimum Total Supply Voltage | ±1.35 V |
| Maximum Total Supply Voltage | ±18 V |
| Rango de temperatura de funcionamiento | -40 °C to +85 °C |
| Encapsulado | 8-pin SOIC |
| Tipo de montaje | Surface mount |
Guía de configuración de pines de INA132U/2K5 8-pin soic
Configuración de pines para INA132U/2K5 (encapsulado 8-pin soic). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para INA132U/2K5.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
INA132U/2K5 es adecuado para 6 aplicacións: Bridge Transducer Signal Conditioning, Precision Shunt Current Sensing, Battery-Powered Sensor Interface, Industrial Process Monitoring, Low-Level Differential Signal Acquisition, Instrumentation Signal Conditioning.
Bridge Transducer Signal Conditioning
The INA132U/2K5 is well suited to bridge-transducer readout because its integrated resistor network provides a fixed gain of 2.5 and rejects common-mode voltage present on both bridge inputs. Connect the bridge excitation across the device supply arrangement and route IN+ and IN− as a matched pair to minimize added differential error. The 2.7 V to 36 V supply range supports low-voltage excitation as well as industrial systems. Before deployment, verify the bridge output at zero and full scale, check the output against the available supply headroom, and account for the amplifier's gain error in the measurement budget.
Recomendado
Precision Shunt Current Sensing
The INA132U/2K5 can amplify the small differential voltage generated by a current shunt while rejecting the larger common-mode voltage on the shunt nodes. Its 2.5 V/V fixed gain increases the measurement signal without requiring an external gain network. Use Kelvin routing from the shunt to IN+ and IN− so copper and connector resistance do not appear as sensed voltage. The single-supply operation supports compact battery-powered monitoring, but the system must preserve output headroom and remain within the input common-mode range during startup and fault conditions.
Recomendado
Battery-Powered Sensor Interface
The INA132U/2K5 fits low-power sensor interfaces because it operates from a single supply beginning at 2.7 V and integrates the precision gain-setting network. It can amplify a differential sensor output while operating from a compact 3.3 V rail, reducing the need for external resistors and associated board area. Power-system designers should still calculate operating current from the manufacturer specifications and verify shutdown behavior separately because the INA132 is intended for continuous low-power signal conditioning rather than duty-cycled operation.
Recomendado
Industrial Process Monitoring
Industrial process monitoring benefits from the INA132U/2K5's fixed 2.5 gain and integrated precision resistor network because sensor outputs can be conditioned close to the measurement source. The 2.7 V to 36 V supply range allows use in both compact instrumentation and higher-voltage industrial systems when the rails are otherwise suitable. Place the amplifier near the sensor connector, maintain symmetrical differential routing, and isolate it from motor-control and relay-switching nodes. Verify the process input range, sensor excitation requirements, and required analog-to-digital converter full-scale voltage before finalizing the signal chain.
Recomendado
Low-Level Differential Signal Acquisition
The INA132U/2K5 is useful when a small differential signal must be elevated before conversion or comparison, particularly when the source contains a much larger common-mode component. Its fixed 2.5 gain preserves a compact implementation while the internal precision network improves consistency between devices. Use short, matched traces and a stable reference arrangement to minimize offset and common-mode conversion. Confirm that the amplified signal remains inside the output swing, and account for the 2.5 multiplication when choosing downstream analog-to-digital converter ranges.
Recomendado
Instrumentation Signal Conditioning
The INA132U/2K5 provides a practical first stage for instrumentation signals that require differential sensing and fixed amplification. Its 8-pin SOIC package supports conventional surface-mount assembly, and the integrated gain network reduces component count compared with a discrete precision difference amplifier. Designers should assess offset, gain tolerance, common-mode rejection, and output range for each measurement class using the manufacturer limits. For high-gain or highly variable systems, a programmable or higher-gain instrumentation amplifier may offer more adjustment flexibility than this fixed 2.5-gain device.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para INA132U/2K5 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | INA132UA/2K5 |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC |
| Device Type | Low-power, single-supply difference amplifier | Low-power, single-supply difference amplifier |
| Fixed Gain | 2.5 V/V | 2.5 V/V |
| Number of Circuits | 1 circuit | 1 circuit |
| Supply Voltage Range | 2.7 V to 36 V | 2.7 V to 36 V |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C |
| Mounting Type | Surface mount | Surface mount |
| Integrated Precision Resistor Network | Yes | Yes |
| Ordering Difference | INA132U/2K5 ordering code | INA132UA/2K5 ordering code; delivery format differs |
Diferenciadores clave
- Fixed 2.5 gain with integrated precision resistor network (frente a INA132UA/2K5)
- Single-supply operation across a wide voltage range (frente a INA132UA/2K5)
- Surface-mount instrumentation footprint (frente a INA132UA/2K5)
Notas de diseño
Route IN+ and IN− as a closely matched differential pair and connect both amplifier inputs to the sensor or shunt with equal trace lengths and symmetric geometry. Current flowing through mismatched input resistance creates differential error even when the amplifier's common-mode rejection is high. Place the device near the source, minimize loop area, and keep switching-node copper and high-current return paths away from the differential inputs.
Place the supply bypass capacitor immediately adjacent to the amplifier's supply and ground pins, using the shortest electrical path available. Keep the supply return above or adjacent to the sensitive input traces rather than sharing a noisy return segment with relays, motors, or LEDs. Validate the input common-mode and output-swing limits with the actual 2.7 V to 36 V operating rail because the usable signal range is narrower than the supply range.
Do not select a different INA132 gain version solely because it uses the same 8-pin SOIC outline. The base INA132 and INA132UA/2K5 family ordering options can have different gain behavior, while INA143UA and AD8278ARZ may use different gain architectures. A physical footprint match does not guarantee signal-level compatibility; confirm the gain equation, common-mode range, output swing, supply limits, and reference-pin use before substitution.
Información de cumplimiento
The manufacturer identifies the INA132U/2K5 as active, but specific environmental and material-compliance statements require confirmation from the current manufacturer documentation or declaration.