onsemi

LM2901VDG - 3-36V Quad Differential Comparator | onsemi

料号: LM2901VDG ✓ 量产中
3 V to 36 V Vdss 25 nA Id 14-SOIC, 0.154 inch / 3.90 mm width Package
最小起订量: 1 |

LM2901VDG 概述

The onsemi LM2901VDG is a quad differential comparator containing four independent general-purpose comparator channels, each with CMOS, open-collector, and TTL-compatible output, in a 14-SOIC package. It operates from 3 V to 36 V in a single-supply configuration or from ±1.5 V to ±18 V in a dual-supply configuration, and its extended-temperature operating range is -40°C to +125°C.

A comparator is an analog integrated circuit that evaluates two input voltages and produces a digital logic state indicating which input is higher. The LM2901 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its four channels are electrically independent, allowing a single package to implement four threshold, level-detection, sensing, or monitoring functions while sharing a common power supply and ground.

The LM2901VDG combines a 2 mV offset specification with 25 nA input-bias current, low supply-current drain, and a wide operating-supply range. Each open-collector output can interface with TTL, CMOS, and MOS logic. A 0.8 mA typical supply-current drain and supply-independent current consumption make the device suitable for systems where predictable current use is important across a broad supply range.

The V-suffix family is specified for extended temperature operation. The manufacturer datasheet identifies tested operating limits of 30 V for the relevant device family and describes single-supply or dual-supply operation. Because the outputs are open collector, external pull-up resistors are required when the outputs must drive a high logic level, and the pull-up voltage and sink-current capability must be checked against the connected logic load.

Typical uses include industrial voltage-threshold detection, low-level sensing, consumer equipment, automotive interface functions, and memory-control logic. Its four independent channels can monitor several control signals simultaneously, while the broad supply range permits operation from low-voltage single supplies to higher-voltage split rails. The same-package footprint also supports comparator consolidation when a board requires more than one sensing channel.

For PCB implementation, place bypass capacitance close to the supply and ground pins, route each high-impedance input away from switching nodes, and use the pull-up resistor to establish the required output rise time. Because open-collector outputs can pull only to a low state, omit pull-up resistors only when another device provides the required active pull-up. Check input common-mode limits, output timing, and absolute maximum voltage before connecting external signals.

This product page combines the manufacturer's device information with practical comparison, application, pinout, and PCB-design guidance. It helps engineers evaluate the LM2901VDG as a four-channel general-purpose comparator while preserving the distinction between verified electrical limits, device-family information, and design decisions that must be confirmed against the manufacturer datasheet.

直接替换替代料: LM2901VDG ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: LM2901VDG (相同外形与封装尺寸) ——差异在于 Comparator Type, Package, Output Type, Number of Channels, Input Bias Current.

onsemi
Comparator Type: General Purpose
Package: 14-SOIC
Output Type: Open Collector
对比 LM2901VDG →
onsemi
Comparator Type: Quad differential voltage comparator
Package: 14-pin SOIC
Output Type: Open collector
对比 LM2901VDG →
onsemi
Comparator Type: Quad differential comparator
Package: 14-pin SOIC
Output Type: Open collector
对比 LM2901VDG →
onsemi
Comparator Type: 4-channel differential comparator
Package: 14-pin SOIC
Output Type: Open collector
对比 LM2901VDG →

LM2901DG

✅ 直接替换
onsemi
📦 14-SOIC
General Purpose · 4 · 3 V to 36 V · ±1.5 V to ±18 V · 1.3 us · Open Collector · CMOS, TTL · 1 mA

联系询价

查看数据手册 →

LM2901DR2G

✅ 直接替换
onsemi
📦 14-SOIC
Quad differential comparator · 4 channels · 3 V to 36 V · -40°C to +105°C · Open collector · CMOS and TTL · 14-pin SOIC · Surface mount

联系询价

查看数据手册 →

LM2901VD

✅ 直接替换
onsemi
📦 14-SOIC
4-channel differential comparator · 3 V to 36 V · 25 nA typical · ±5.0 nA typical · Open collector · TTL compatible · Single or split supply · 4

联系询价

查看数据手册 →

LM2901DR2

✅ 直接替换
onsemi
📦 14-SOIC
Quad differential voltage comparator · 4 channels · 3 V to 36 V · 25 nA typical · Open collector · Single supply or split supply

联系询价

查看数据手册 →

LM2901VDR

✅ 直接替换
📦 14-SOIC
Cross-brand V-family option with the same four-channel 14-SOIC architecture and a 30 V rated supply; temperature limits require verification.

📋 参考替代料(不在目录中)

LM2901VDG 最大额定值与电气特性

Comparator Type General-purpose differential comparator
Number of Channels 4 channels
Single-Supply Voltage Range 3 V to 36 V
Dual-Supply Voltage Range ±1.5 V to ±18 V
Tested Maximum Supply Voltage 30 V
输出类型 Open-collector, CMOS and TTL compatible
Input Offset Voltage 2 mV
Input Bias Current 25 nA
Supply-Current Drain 0.8 mA typical
工作温度范围 -40°C to +125°C
封装 14-SOIC, 0.154 inch / 3.90 mm width
安装类型 Surface mount
Manufacturer Description Single-supply quad comparator

LM2901VDG 引脚配置

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
引脚 1 OUT1 — Comparator 1 open-collector output
引脚 2 IN1- — Comparator 1 inverting input
引脚 3 IN1+ — Comparator 1 noninverting input
引脚 4 GND — Ground reference
引脚 5 IN2+ — Comparator 2 noninverting input
引脚 6 IN2- — Comparator 2 inverting input
引脚 7 OUT2 — Comparator 2 open-collector output
引脚 8 OUT3 — Comparator 3 open-collector output
引脚 9 IN3- — Comparator 3 inverting input
引脚 10 IN3+ — Comparator 3 noninverting input
引脚 11 VCC — Positive supply input
引脚 12 IN4+ — Comparator 4 noninverting input
引脚 13 IN4- — Comparator 4 inverting input
引脚 14 OUT4 — Comparator 4 open-collector output

典型应用

LM2901VDG 适用于 6 应用s: Industrial Voltage-Level Detection, Automotive Low-Level Sensing, Consumer Equipment Threshold Monitoring, Power-Supply Rail Monitoring, Memory and Control Logic, Sensor Signal Conditioning.

🏭

Industrial Voltage-Level Detection

The LM2901VDG fits industrial threshold detection because it combines four differential comparator channels with a 3 V to 36 V single-supply range and a -40°C to +125°C operating specification. Each channel can compare a sensed voltage against an adjustable or fixed reference, producing an open-collector logic result for a controller input. The 2 mV offset target supports low-level decisions, while 25 nA input-bias current limits disturbance at high-impedance sensing nodes. Place pull-up resistors on all four outputs and keep input traces away from switching power stages to prevent false threshold transitions.

🚗

Automotive Low-Level Sensing

LM2901VDG can be used for automotive low-level sensing when the selected ordering code satisfies the vehicle's voltage, temperature, and qualification requirements. Four independent channels permit monitoring of multiple analog signals against separate reference levels, and the broad 3 V to 36 V operating range supports systems above conventional 5 V rails. The 25 nA input-bias current and 2 mV offset specification help preserve small-signal decisions, while the -40°C to +125°C range covers temperature conditions. Automotive qualification documentation must be confirmed before treating the device as AEC-Q100 qualified.

📱

Consumer Equipment Threshold Monitoring

The four-channel LM2901VDG consolidates several consumer-equipment threshold checks into one 14-SOIC device. It can monitor battery or signal levels, compare sensor outputs with reference voltages, and provide open-collector states that connect to CMOS, TTL, or MOS logic. Its 3 V minimum single-supply voltage supports low-voltage systems, and the typical 0.8 mA supply-current drain provides a predictable operating load. Because the output is open collector, the designer must add suitable pull-up resistors and verify that output rise time meets the receiving circuit's requirements.

⚡

Power-Supply Rail Monitoring

LM2901VDG is suitable for monitoring multiple power rails where the logic system needs to know whether each voltage remains above or below a threshold. Its 3 V to 36 V single-supply operation allows direct sensing in higher-voltage systems when the common-mode and absolute-maximum limits are respected. Four channels can supervise several rails without requiring four separate packages, reducing board area while retaining independent comparisons. A practical design should use filtered divider nodes at the inputs, account for comparator response time, and select pull-up values that balance current consumption against the required logic transition speed.

🖥️

Memory and Control Logic

The LM2901VDG fits memory and control-logic functions requiring four independent comparison decisions. It can evaluate address, enable, reset, or data-valid signals and translate analog threshold relationships into open-collector logic states. The quad architecture provides four channels in one 14-SOIC package, while the 3 V to 36 V range accommodates single- and dual-supply arrangements. Designers should account for propagation delay and input overdrive in timing analysis, connect unused channels to defined levels, and provide pull-up resistors wherever a logic-high output is required.

🧩

Sensor Signal Conditioning

LM2901VDG can convert a conditioned analog sensor signal into a logic decision when the signal can be compared against a reference within the input common-mode range. Its 2 mV offset target and 25 nA input-bias current are useful for high-impedance sensing networks, while four channels allow multiplexing-related comparisons without separate packages. The open-collector output can directly interface with suitable CMOS, TTL, or MOS logic after adding pull-up resistors. High-impedance traces should be short, guarded where practical, and physically separated from switching nodes to minimize injected noise and erroneous comparator transitions.

What are the key specifications of LM2901VDG that engineers should know?
The LM2901VDG is a four-channel general-purpose differential comparator rated for 3 V to 36 V single-supply operation and ±1.5 V to ±18 V dual-supply operation. According to the onsemi datasheet, it provides open-collector outputs compatible with CMOS and TTL, a 2 mV offset specification, 25 nA input-bias current, and a typical supply-current drain of 0.8 mA. It is packaged in 14-SOIC and operates from -40°C to +125°C.
What is the operating voltage of LM2901VDG?
The LM2901VDG operates from 3 V to 36 V with a single supply, or from ±1.5 V to ±18 V with dual supplies. The onsemi datasheet describes wide-range single- or dual-supply operation and identifies 30 V as a tested operating limit for the V-suffix device family. Engineers should also observe the absolute maximum ratings, which are distinct from the normal operating range, when evaluating transients and fault conditions.
Where can I download the LM2901VDG datasheet PDF?
The LM2901VDG datasheet can be accessed through the onsemi LM2901 product page at https://www.onsemi.com/products/standard-products/amplifiers-comparators/comparators/lm2901. The manufacturer describes the device as a quad, single-supply comparator with a 36 V rating. Use the manufacturer document for authoritative pin assignments, electrical limits, timing characteristics, and recommended application details before completing a production design.
Where can I find the LM2901VDG pinout?
The LM2901VDG uses a standard 14-SOIC comparator pinout: outputs occupy pins 1, 7, 8, and 14; noninverting inputs occupy pins 3, 5, 10, and 12; inverting inputs occupy pins 2, 6, 9, and 13; ground is pin 4; and supply is pin 11. Confirm the mapping in the onsemi datasheet when assigning PCB nets and before applying power.
What can replace the LM2901VDG?
The LM2901DG is a closely related onsemi drop-in candidate in the same 14-SOIC package, with no stated difference in the 3 V to 36 V supply range. The LM2901DR2G is another same-family option, while TI LM2901DR and LM2901VDR devices offer the same quad-comparator architecture in a 14-SOIC footprint. Verify temperature grade, offset, bias-current, timing, and absolute-maximum ratings for the selected replacement before production use.
Is LM2901VDG the same as LM2901DG?
No, LM2901VDG and LM2901DG are related LM2901-family devices, but their suffix-specific qualifications and ratings should be checked before substitution. Both are four-channel general-purpose comparators in 14-SOIC and support the same 3 V to 36 V single-supply range. The safer approach is to compare the suffix-specific temperature and electrical specifications in each manufacturer datasheet.
What is the best TI equivalent for LM2901VDG?
The TI LM2901DR and LM2901VDR are the closest TI quad-comparator candidates because both use a 14-SOIC footprint and implement four differential comparator channels. TI identifies the LM2901 as a 30 V quad differential comparator and describes the B-version family as a drop-in replacement for earlier LM2901 versions. Exact equivalence still depends on the required temperature grade, supply range, timing, and offset limits.
When should I choose LM2901VDG over LM2901DG?
Choose LM2901VDG when the design requires the V-suffix device family and its -40°C to +125°C operating-temperature specification. LM2901DG remains relevant for designs whose requirements match that part's grade. Because both use the same 14-SOIC footprint and four-channel architecture, selection should be based on verified suffix-specific temperature, offset, bias-current, supply-current, and qualification requirements rather than package availability alone.
LM2901VDG vs LM2901DR - which is better for industrial level detection?
LM2901VDG is the appropriate onsemi choice when its -40°C to +125°C range covers the industrial environment and the 2 mV offset and 25 nA bias-current targets are required. LM2901DR may suit designs covered by TI's own qualification limits. For industrial level detection, compare input common-mode range, response time, output sink current, supply variation, and channel-to-channel behavior as well as temperature coverage.
Is LM2901VDG suitable for automotive voltage-level sensing?
LM2901VDG can support voltage-level sensing when the system's voltage, temperature, noise, and qualification requirements match the device ratings. The part provides four differential comparator channels, a 3 V to 36 V operating range, and a -40°C to +125°C temperature specification. AEC-Q100 qualification is not established in the manufacturer information for this ordering code, so request the specific automotive qualification documentation before using it in an AEC-Q100 design.
Where can I buy LM2901VDG and what is the current lead time?
Use the Request a Quote form on this page to ask about LM2901VDG availability, current lead time, and order quantity. The form is the appropriate channel for a current commercial response because inventory and lead time can change independently of the device specifications. Package quantity requirements and production schedule should be stated in the same request to help determine the appropriate sourcing plan.
What is the price of LM2901VDG?
A current price for LM2901VDG should be obtained through the Request a Quote form on this page. The form supports an exact-order quotation for the onsemi LM2901VDG in its 14-SOIC configuration. Include the required quantity, production quantity, and packaging preference so the commercial response can reflect the appropriate manufacturing and fulfillment basis.
Is LM2901VDG in stock?
LM2901VDG stock should be confirmed through the Request a Quote form on this page rather than assumed from a catalog listing. Provide the required quantity, packaging preference, and target delivery date. The manufacturer device page identifies the LM2901 family as a 36 V quad comparator, while current inventory status remains a time-dependent commercial condition.
How does LM2901VDG compare with LM2901DR2G?
LM2901VDG and LM2901DR2G are same-family, four-channel comparator options associated with a 14-SOIC footprint. The principal engineering question is whether their suffix-specific temperature grade and electrical limits satisfy the application; the documented supply range is 3 V to 36 V for the LM2901VDG. Review offset voltage, input-bias current, response time, common-mode range, and output-current limits in the relevant datasheets before substitution.
What design considerations apply to LM2901VDG open-collector outputs?
Each LM2901VDG output requires an external pull-up resistor when driving a logic high because the output stage is open collector. Select the resistor to obtain the required logic voltage and acceptable rise time, then verify that the connected load and pull-up network remain within the output sink-current rating. According to the onsemi datasheet, the outputs are compatible with CMOS, TTL, and MOS logic interfaces.

工程参考数据: LM2901VDG ——对比、设计指导和合规信息。

选型指南

Choose LM2901VDG when the design needs four independent general-purpose comparator channels, operation from a 3 V to 36 V single supply, open-collector outputs compatible with CMOS and TTL, and an extended-temperature range of -40°C to +125°C. It is particularly suitable for industrial voltage detection, low-level sensing, rail supervision, and control logic where the application can use the 2 mV offset and 25 nA input-bias characteristics. LM2901DG is a closely related onsemi option when its suffix-specific temperature and electrical ratings match the design. LM2901DR2G and LM2901VD may also fit the same 14-SOIC family architecture, but their ordering-code qualifications must be reviewed. For a cross-brand replacement, LM2901DR and LM2901VDR provide the same four-channel 14-SOIC format, but the 30 V family rating is lower than the 36 V single-supply rating associated with LM2901VDG. For any substitution, confirm common-mode range, absolute maximum ratings, response time, output sink current, offset, bias current, and automotive qualification requirements before releasing production artwork.

与替代料对比

参数 本产品 LM2901DG LM2901DR2G LM2901VD LM2901DR LM2901VDR
Brand onsemi onsemi onsemi onsemi Texas Instruments Texas Instruments
Package 14-SOIC 14-SOIC - same 14-SOIC - same 14-SOIC - same 14-SOIC - same 14-SOIC - same
Comparator Channels 4 channels 4 channels 4 channels 4 channels 4 channels 4 channels

关键差异点

  • Four independent comparator channels in one package (对比 LM2901DR)
  • Extended-temperature V-suffix operation (对比 LM2901DG)
  • Wide single-supply operating range (对比 LM2901DR)
  • Low bias current for high-impedance sensing (对比 LM2901VD)

设计说明

Keep the four input nets short and route them away from switching nodes, inductors, and high-current return paths. Comparator inputs can be sensitive to parasitic pickup even when the supply and ground arrangement is correct. Use a solid ground plane, provide local supply bypassing, and place the device near the sensed sources when the application involves high-impedance signals. Verify the final layout by checking output behavior near the intended threshold.

Add an external pull-up resistor to every output that must drive a logic-high state because the LM2901VDG uses an open-collector output stage. Select the resistor using the required rise time, the input capacitance of the receiving logic, and the maximum sink current. Ensure the pull-up voltage remains within the comparator output rating and the load current remains within the absolute maximum output-current limits shown in the manufacturer datasheet.

Do not treat the normal operating supply range as the absolute maximum rating. Separately review supply-voltage transients, differential input voltage, common-mode input limits, and output loading. Also avoid leaving unused comparator channels floating; connect each unused input to a defined potential and leave the corresponding output without a required load if the package function permits it.

Open-collector outputs can exhibit slow rising edges when the pull-up resistance is too high or the load capacitance is large. Use the pull-up value to establish a switching time compatible with the receiving circuit, and keep the output trace short. If the comparator drives a cable or isolated interface, add an appropriate driver rather than relying on the open-collector stage to provide long-distance signal integrity.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The manufacturer product page and available technical listings do not state the exact compliance status for this ordering code. Obtain the current onsemi declaration or material-declaration documentation before making a compliance claim.

相关搜索

LM2901VDG datasheet LM2901VDG pinout LM2901VDG datasheet pdf LM2901VDG specifications LM2901VDG 3-36V comparator LM2901VDG 14-SOIC LM2901VDG equivalent LM2901VDG replacement LM2901VDG vs LM2901DR LM2901VDG price LM2901VDG stock onsemi LM2901VDG LM2901VDG voltage level detection LM2901VDG automotive sensing

相关元器件 & 术语

onsemi LM2901VDG LM2901DG LM2901DR2G LM2901VD LM2901DR LM2901VDR quad differential comparator comparator analog integrated circuit mixed-signal semiconductor open-collector output TTL-compatible output CMOS-compatible output single-supply operation dual-supply operation input offset voltage input bias current supply-current drain common-mode input voltage range 14-SOIC SOIC package family surface-mount package RoHS REACH industrial voltage detection automotive low-level sensing
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情