LM2901VDG - 3-36V Quad Differential Comparator | onsemi
MPN: LM2901VDG ✓ AktifLM2901VDG Ringkasan
A comparator is an analog integrated circuit that evaluates two input voltages and produces a digital logic state indicating which input is higher. The LM2901 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its four channels are electrically independent, allowing a single package to implement four threshold, level-detection, sensing, or monitoring functions while sharing a common power supply and ground.
The LM2901VDG combines a 2 mV offset specification with 25 nA input-bias current, low supply-current drain, and a wide operating-supply range. Each open-collector output can interface with TTL, CMOS, and MOS logic. A 0.8 mA typical supply-current drain and supply-independent current consumption make the device suitable for systems where predictable current use is important across a broad supply range.
The V-suffix family is specified for extended temperature operation. The manufacturer datasheet identifies tested operating limits of 30 V for the relevant device family and describes single-supply or dual-supply operation. Because the outputs are open collector, external pull-up resistors are required when the outputs must drive a high logic level, and the pull-up voltage and sink-current capability must be checked against the connected logic load.
Typical uses include industrial voltage-threshold detection, low-level sensing, consumer equipment, automotive interface functions, and memory-control logic. Its four independent channels can monitor several control signals simultaneously, while the broad supply range permits operation from low-voltage single supplies to higher-voltage split rails. The same-package footprint also supports comparator consolidation when a board requires more than one sensing channel.
For PCB implementation, place bypass capacitance close to the supply and ground pins, route each high-impedance input away from switching nodes, and use the pull-up resistor to establish the required output rise time. Because open-collector outputs can pull only to a low state, omit pull-up resistors only when another device provides the required active pull-up. Check input common-mode limits, output timing, and absolute maximum voltage before connecting external signals.
This product page combines the manufacturer's device information with practical comparison, application, pinout, and PCB-design guidance. It helps engineers evaluate the LM2901VDG as a four-channel general-purpose comparator while preserving the distinction between verified electrical limits, device-family information, and design decisions that must be confirmed against the manufacturer datasheet.
Pilihan pengganti yang segera untuk LM2901VDG — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera LM2901VDG (sama faktor bentuk dan kaki) — berbeza dalam Comparator Type, Package, Output Type, Number of Channels, Input Bias Current.
LM2901DG
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM2901DR2G
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM2901VD
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM2901DR2
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM2901VDR
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LM2901VDG Penilaian maksimum & Ciri-ciri Elektrik
| Comparator Type | General-purpose differential comparator |
| Number of Channels | 4 channels |
| Single-Supply Voltage Range | 3 V to 36 V |
| Dual-Supply Voltage Range | ±1.5 V to ±18 V |
| Tested Maximum Supply Voltage | 30 V |
| Jenis Output | Open-collector, CMOS and TTL compatible |
| Input Offset Voltage | 2 mV |
| Input Bias Current | 25 nA |
| Supply-Current Drain | 0.8 mA typical |
| Gambaran Suhu Operasi | -40°C to +125°C |
| Kemasan | 14-SOIC, 0.154 inch / 3.90 mm width |
| Jenis Pemasangan | Surface mount |
| Manufacturer Description | Single-supply quad comparator |
Konfigurasi Pin LM2901VDG
| Pin 1 | OUT1 — Comparator 1 open-collector output |
| Pin 2 | IN1- — Comparator 1 inverting input |
| Pin 3 | IN1+ — Comparator 1 noninverting input |
| Pin 4 | GND — Ground reference |
| Pin 5 | IN2+ — Comparator 2 noninverting input |
| Pin 6 | IN2- — Comparator 2 inverting input |
| Pin 7 | OUT2 — Comparator 2 open-collector output |
| Pin 8 | OUT3 — Comparator 3 open-collector output |
| Pin 9 | IN3- — Comparator 3 inverting input |
| Pin 10 | IN3+ — Comparator 3 noninverting input |
| Pin 11 | VCC — Positive supply input |
| Pin 12 | IN4+ — Comparator 4 noninverting input |
| Pin 13 | IN4- — Comparator 4 inverting input |
| Pin 14 | OUT4 — Comparator 4 open-collector output |
Aplikasi Biasa
LM2901VDG patut untuk 6 aplikasis: Industrial Voltage-Level Detection, Automotive Low-Level Sensing, Consumer Equipment Threshold Monitoring, Power-Supply Rail Monitoring, Memory and Control Logic, Sensor Signal Conditioning.
Industrial Voltage-Level Detection
The LM2901VDG fits industrial threshold detection because it combines four differential comparator channels with a 3 V to 36 V single-supply range and a -40°C to +125°C operating specification. Each channel can compare a sensed voltage against an adjustable or fixed reference, producing an open-collector logic result for a controller input. The 2 mV offset target supports low-level decisions, while 25 nA input-bias current limits disturbance at high-impedance sensing nodes. Place pull-up resistors on all four outputs and keep input traces away from switching power stages to prevent false threshold transitions.
Disebarkan
Automotive Low-Level Sensing
LM2901VDG can be used for automotive low-level sensing when the selected ordering code satisfies the vehicle's voltage, temperature, and qualification requirements. Four independent channels permit monitoring of multiple analog signals against separate reference levels, and the broad 3 V to 36 V operating range supports systems above conventional 5 V rails. The 25 nA input-bias current and 2 mV offset specification help preserve small-signal decisions, while the -40°C to +125°C range covers temperature conditions. Automotive qualification documentation must be confirmed before treating the device as AEC-Q100 qualified.
Disebarkan
Consumer Equipment Threshold Monitoring
The four-channel LM2901VDG consolidates several consumer-equipment threshold checks into one 14-SOIC device. It can monitor battery or signal levels, compare sensor outputs with reference voltages, and provide open-collector states that connect to CMOS, TTL, or MOS logic. Its 3 V minimum single-supply voltage supports low-voltage systems, and the typical 0.8 mA supply-current drain provides a predictable operating load. Because the output is open collector, the designer must add suitable pull-up resistors and verify that output rise time meets the receiving circuit's requirements.
Disebarkan
Power-Supply Rail Monitoring
LM2901VDG is suitable for monitoring multiple power rails where the logic system needs to know whether each voltage remains above or below a threshold. Its 3 V to 36 V single-supply operation allows direct sensing in higher-voltage systems when the common-mode and absolute-maximum limits are respected. Four channels can supervise several rails without requiring four separate packages, reducing board area while retaining independent comparisons. A practical design should use filtered divider nodes at the inputs, account for comparator response time, and select pull-up values that balance current consumption against the required logic transition speed.
Disebarkan
Memory and Control Logic
The LM2901VDG fits memory and control-logic functions requiring four independent comparison decisions. It can evaluate address, enable, reset, or data-valid signals and translate analog threshold relationships into open-collector logic states. The quad architecture provides four channels in one 14-SOIC package, while the 3 V to 36 V range accommodates single- and dual-supply arrangements. Designers should account for propagation delay and input overdrive in timing analysis, connect unused channels to defined levels, and provide pull-up resistors wherever a logic-high output is required.
Disebarkan
Sensor Signal Conditioning
LM2901VDG can convert a conditioned analog sensor signal into a logic decision when the signal can be compared against a reference within the input common-mode range. Its 2 mV offset target and 25 nA input-bias current are useful for high-impedance sensing networks, while four channels allow multiplexing-related comparisons without separate packages. The open-collector output can directly interface with suitable CMOS, TTL, or MOS logic after adding pull-up resistors. High-impedance traces should be short, guarded where practical, and physically separated from switching nodes to minimize injected noise and erroneous comparator transitions.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk LM2901VDG — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | LM2901DG | LM2901DR2G | LM2901VD | LM2901DR | LM2901VDR |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments |
| Package | 14-SOIC | 14-SOIC - same | 14-SOIC - same | 14-SOIC - same | 14-SOIC - same | 14-SOIC - same |
| Comparator Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
Penyeberangsung Jelas
- Four independent comparator channels in one package (vsLM2901DR)
- Extended-temperature V-suffix operation (vsLM2901DG)
- Wide single-supply operating range (vsLM2901DR)
- Low bias current for high-impedance sensing (vsLM2901VD)
Catatan Desain
Keep the four input nets short and route them away from switching nodes, inductors, and high-current return paths. Comparator inputs can be sensitive to parasitic pickup even when the supply and ground arrangement is correct. Use a solid ground plane, provide local supply bypassing, and place the device near the sensed sources when the application involves high-impedance signals. Verify the final layout by checking output behavior near the intended threshold.
Add an external pull-up resistor to every output that must drive a logic-high state because the LM2901VDG uses an open-collector output stage. Select the resistor using the required rise time, the input capacitance of the receiving logic, and the maximum sink current. Ensure the pull-up voltage remains within the comparator output rating and the load current remains within the absolute maximum output-current limits shown in the manufacturer datasheet.
Do not treat the normal operating supply range as the absolute maximum rating. Separately review supply-voltage transients, differential input voltage, common-mode input limits, and output loading. Also avoid leaving unused comparator channels floating; connect each unused input to a defined potential and leave the corresponding output without a required load if the package function permits it.
Open-collector outputs can exhibit slow rising edges when the pull-up resistance is too high or the load capacitance is large. Use the pull-up value to establish a switching time compatible with the receiving circuit, and keep the output trace short. If the comparator drives a cable or isolated interface, add an appropriate driver rather than relying on the open-collector stage to provide long-distance signal integrity.
Maklumat Kesediaan
The manufacturer product page and available technical listings do not state the exact compliance status for this ordering code. Obtain the current onsemi declaration or material-declaration documentation before making a compliance claim.